This short video explains NMEA 2000 and shows the setup of a basic NMEA 2000 network.
Пікірлер: 50
@handrepairman2 ай бұрын
That was great ! Five-star video. Thanks for the knowledge!
@zash0085 жыл бұрын
The single best cost to reward ratio on an upgrade a boat owner will ever see. Easiest upgrade to install you will ever see also!
@williamhalling77443 жыл бұрын
FYI, the power cable should always be connected as close to the center of the backbone as possible.
@jamesm73463 жыл бұрын
Good job guys, you answer bunch of questions for me thanks
@TheGPSStore11 жыл бұрын
Great question. The HDS does require its own power source. There are units that will power from the NMEA 2000 backbone but most MFD displays require their own power.
@Grunnsetning11 жыл бұрын
You need a NMEA 2000 starter kit and a cable that will send the info from the motor to the network. Lowrance has one for yamaha for example. 120-37 is the number.
@christiantroulliet63379 жыл бұрын
I am installing a lowrance hds7 Gen 2 Touch GPS to a Motor guide XI5 trolling motor via the nmea 2000 do I need to run extra wires or is there a certain connector that I have to order
@salvatoresimonetti92808 жыл бұрын
thank you very good explanation
@anguslf24 жыл бұрын
Hi doctor, do you know why everyone pronounce NMEA as "NEMA" ???? this really confuse me
@Philiphfisch9 жыл бұрын
Clear and intresting video!
@cpobyrne13 жыл бұрын
very helpful - thanks. does the network consume any power when the instruments are switched off?
@cindewalker26434 жыл бұрын
What kind of equipment do I need too purchase for my HDS-8 GENERATION 1 to get the satilite to operate and to get the maxim capabilities with out breaking me? Thank u very much! I’ve bought the. Cable kit
@RichieLott6 жыл бұрын
Good info for folks just starting up. Works FLAWLESSLY with most any later model Garmin GPS map plotter head/mfd. Don't really understand why it couldn't be USB or cat 5 cable, but I get that it's cleaner and a single power cord
@100krypton3 жыл бұрын
Can I use a 2000 to 0182 nmea adapter to plug into a C70 PLOTTER?
@Etrain0314411 жыл бұрын
Thanks for putting this video together. Does the HDS also need a power source, separate from the power to the NMEA? Or does the power that supports the backbone also supply power to all devices connected to the NMEA backbone?
@colbybud3 жыл бұрын
lowrance needs seperate power
@RobaloBill10 жыл бұрын
I understand that there is a connection on the Yamaha 150 4 stoke that will link to this NMEA2000 system. I have the exact configuration, but would like to see the data on my Garmin 740s. Some research indicates I need a Garmin Yamaha engine interface cable. This cable should feed all the data I need. However there is some controversy as to whether or not fuel consumption is part of this data stream. Would I need to add the Garmin GFS 10 fuel sensor?
@geomatrix545210 жыл бұрын
Hi Scott. Great explanation of how to build a NMEA 2000 network. How would I use the Furuno BBWGPS NavNet GPS Receiver to provide data directly to my PC and MaxSea Time Zero?
@bill507410 жыл бұрын
Great video !!! I am going to install this NMEA 2000 system on my bass boat that has an HDS 8 Gen2 at the console and an HDS7 Gen 2 on the front deck. Is the Lowrance system as easy as this Garmin ? Also would you suggest the Point 1 antenna or the LGC 4000 ? Thanks, Bill
@scottheffernan944510 жыл бұрын
Hi Geo Matrix, First we need to know if you have used the BBWGPS with a Navnet. If so you will not be able to use it with the PC. If not, then you will have to connect it through an RS232 port, assuming your PC still has one.
@TheSailingChannel9 жыл бұрын
Can you create a Garmin T-Connector backbone at the helm where the connectors will be exposed to weather? I.E., are they weatherproof or does the backbone need to be in a weather-protected space?
@DVincenzi53 жыл бұрын
Is it possible to share radar and sonar between a garmin 741xs and a garmin 742 xs and or a 942 xs using the nema 2000?
@Etrain0314411 жыл бұрын
Thank you. I sure wish the NMEA powered everything. I have a 21 foot Nitro with 4 batteries currently in the boat. Do you believe I need a fifth battery to support an HDS 10 gen + HDS 12 Touch + Sonic Hub? I fish maybe 10 hours at time (per trip) between recharging opportunities. thank you again
@Fischize10 жыл бұрын
Question: if I have a Lowarnce HDS-8 on the consol, can I use a Garmin on the front deck? If I understand the video, as long as I have a separate power source for the Garmin, the unit will work as long as I use the back-bone.
@svargo19127 жыл бұрын
hi I am trying to hook up my nmea the yellow power cable has 3 wires. one is a silver looking wire with no insulation around it what ad where does that go
@AlexanderKanaev4 жыл бұрын
the "silver" (bare) cable is used to ground the nmea2K network. Connect it to the "minus", same place as the black cable
@SonnyReeves6 жыл бұрын
How important are the terminator end caps? I know they have a 100ohm resistor. Can another device be added instead of a terminator?
@thecaptain87736 жыл бұрын
If you are trying to save a few bucks, best if you just find another interest. Boat the proper way that is fun is expensive. Boating the cheap way always leads to tears and more aggravation than its worth. Trust me, I've tried it both ways.
@p.m.dokman25516 жыл бұрын
kun je een marifoon horizon gx2200 ook met neme 2000 aansluiten in opgaaf staat alleen neme 0183 ???
@davidmaschke88016 жыл бұрын
Thank you for this. Can the backbone make a 90 degree turn?
@ralphbell17865 жыл бұрын
They make L-shaped connectors for tight turns, cable will bend to make gradual turns.
@CUBURANYC11 жыл бұрын
tnx for video, q: How do I connect my engine data with 740s....what cable do I need tnx
@CUBURANYC11 жыл бұрын
Tnx!!
@bigrick97764 жыл бұрын
If I was looking to just read what my fuel tank was doing with just my Echo Map Plus 74cv, do I need all the parts listed in the video ? I found the Garmin GFS 10 but still not 100% on what would be needed. That's the only component I want to add to my chartplotter. Basically want to replace the analog fuel gauge.
@neillee37935 жыл бұрын
Is there enough power in the NMEA to run 2 Lowrance HDS units, Radar, transducer, Sonic Hub, Point1 antenna?
@TheGPSStore5 жыл бұрын
The power for the HDS units, Radar and SonicHub come from their own power cables, not the NMEA 2000 network. The transducer will get power from the HDS and the point one antenna will get power from the NMEA 2000 network.
@neillee37935 жыл бұрын
@@TheGPSStore Thank you.
@StevenDeLisa8 жыл бұрын
cool stuff, btw your site should accept paypal credit and regular payable FYI...
@dirkbuys94983 ай бұрын
Nice, but anyone can plug in a cable. Now plug in the power and show how to configure the screen.
@Etrain0314411 жыл бұрын
I was thinking the same thing. I will give you uyd
@felixr33187 жыл бұрын
why terminator
@Tooslowww9 жыл бұрын
Looking to communicate with Suzuki 2009 NMEA backbone and connect to new Garmin. The Suzuki has blue connections that does not connect to the Garmin how do I convert to the new connections? Is this the part number I need ? NVX12705 MAN#: 000-0127-05
@Etrain0314411 жыл бұрын
I will give you guys a call tomorrow afternoon.
@p.m.dokman25516 жыл бұрын
i means name 0183 en name 2000 off course
@anchorsandpilots68506 жыл бұрын
This whole system is a USB wanna be that seems to be a major failure... I don’t see the point
@gerardcollins17674 жыл бұрын
just very expensie bus bar, every thing needs garmin cables at rip off prices.
@TheGPSStore11 жыл бұрын
Give us a call at 1-800-477-2611 and talk to one of our experts.