Good job! Found the solution to my engine hours display by watching your video - Thanks
@p-jjohansson25194 ай бұрын
Thank you, just the info I needed :)
@brianw96342 жыл бұрын
Well done! Great explanation of the engine NMEA connection. You said that you were not able to get the data on the Garmin screen? It should be able to connect to the NMEA bus and play along with the Lowrance and Yamaha. Just do what I do in the airplane... keep pushing buttons until you figure it out. In all seriousness, make sure that you have updated the software on the units. My experience with Garmin is that when there's an update, you want it on there yesterday. As for your mentality on engine maintenance, you are very wise! As a civilian pilot and military aircraft mechanic, you're treating your boat like an airplane. If people did that with their cars and boats, they would not break down nearly as often as they do (most don't even check tire pressures on the car or trailer). I call it keeping the big bad wolf away by being proactive. Well done, sir! I'm subscribing!
@sixfivefishing15282 жыл бұрын
Thank you Brian W. And welcome to the channel.
@scotwcates7 ай бұрын
There are a few interface cables on Amazon some ranging from 35 to 90 dollars I have the f70, they all seem the same not sure which one to get thx
@sixfivefishing15287 ай бұрын
If you have a Yamaha, I got the lowrance Yamaha interface cable.
@elprincipekalvyn19097 ай бұрын
hey i have a question can i connect the interface cable from the motor directly to the gps to the nema 2000 plug in or do i need a command link getaway
@sixfivefishing15287 ай бұрын
I am not sure. But I think you will need a Network Port Expander.
@IvanMoreno-gt8xw9 ай бұрын
Hello any idea on what the problem was connecting to the garmin, I have the same problem not getting any of the motor readings. Thanks for the video very well explained
@sixfivefishing15289 ай бұрын
I never looked into the issue Ivanmoreno. I works great on my lowrance units so I never looked back.
@beyondupnorth2 жыл бұрын
So a outboard motor I face cable needs to be purchased for my 2021 Yamaha 50? Then I need 2 T for drop cables to the engine and the Garmin Echomap? And a 3rd T for the backbone power supply? The a male and female termination resisters, one for each end?
@sixfivefishing15282 жыл бұрын
You are correct beyondupnorth. I used the lowrance interface cable.
@uuurban12 жыл бұрын
Hello, I also want to connect a yamaha 150f detl 2016, but the service technician mentioned to me that I need an adapter for the yamaha engine. As I see it, you mounted it without a jumper and everything works?
@sixfivefishing15282 жыл бұрын
Urban Cunder apologize for not responding to your message until now. Yes, mine works great!!
@Brooklynfishing Жыл бұрын
Helo thanks so you only run o e wire only ,,nothing else i have a garmin 94sv thanks
@sixfivefishing1528 Жыл бұрын
Yes, wire from my engine and you have to run a power wire at the console or the battery it self.
@vedrandujmovic42052 жыл бұрын
How is that you don’t have Yamaha gauges or display? And how you reset oil change reminder?
@sixfivefishing15282 жыл бұрын
Thanks for watching verdant dujmovic. Unfortunately, my zx190 doesn’t come equipped with a Yamaha gauge. I Suspect this is how they kept the price low. This is why I installed a nmea 2000. I don’t have a oil change reminder. I just write the hour on my oil filter at the time I change but I change my before a 100 hours.
@bluexpress242 Жыл бұрын
Did you have any problems getting data on the Lowrance? I just installed the system on a Yamaha to Lowrance and I can’t get anything.
@sixfivefishing1528 Жыл бұрын
Bluexpress2242 no I don’t have any issues. Check the power wire.
@bluexpress242 Жыл бұрын
@@sixfivefishing1528 Thanks will do.
@Ceegar1112 жыл бұрын
Ed, what power source did you hook the NEMA 2000 up to ? they say not to the starting battery ? Thano you Don
@sixfivefishing15282 жыл бұрын
Hi D hardy. I use my auxiliary switch that power my Graphs. I found that to work for me.
@ericbrownbassfishing8303 жыл бұрын
Hey Ed,. I ended up finding a couple after I saw you yesterday at P-Flat. It was a grind tho. Seems like all they wanted was MM on the DS.💯
@sixfivefishing15283 жыл бұрын
What’s up Eric! Yeah they finicky like that. DS is all they want sometime. But I do catch’em on a SH from time to time.
@pacificformula Жыл бұрын
Can you connect this direct to the lowrance or do you need a HUB?
@sixfivefishing1528 Жыл бұрын
Thanks for watching. Yes, or any unit that supports a NMEA 2000.
@pacificformula Жыл бұрын
@@sixfivefishing1528 your welcome & thx for the info!
@troydunn042 жыл бұрын
Great video, however it is a water impeller not propeller.
@sixfivefishing15282 жыл бұрын
Troy, thanks for watching and the correction.
@fishingfool26442 жыл бұрын
Thank you for the info. Just waiting on my cable now.
@sixfivefishing15282 жыл бұрын
Your welcome fishing fool. Hope you love it like I do. And thanks for watching.
@leepierce3256 Жыл бұрын
great video, thanks for sharing!
@sixfivefishing1528 Жыл бұрын
Your welcome Lee pierce.
@cinqzero2839 Жыл бұрын
Great video. Thanks!
@sixfivefishing1528 Жыл бұрын
Glad you liked it!
@bubbasmith70492 жыл бұрын
Great video!
@NYStrucking2 жыл бұрын
Does it read fault code?
@sixfivefishing15282 жыл бұрын
I’m not sure about fault code. If I had to guess, I would say no.
@JR-nw3kj9 ай бұрын
Nice job!
@sixfivefishing15289 ай бұрын
Thanks JR
@Jhwright0711 ай бұрын
Great job!
@sixfivefishing152811 ай бұрын
Thank you for watching jhwright07.
@justinabbott1155 Жыл бұрын
Did you use the screws that came in the box to flush mount it? I just bought this unit and thought it would have bolts and wing nuts for mounting.
@sixfivefishing1528 Жыл бұрын
Thanks for watching Justin Abbott. My lowrance come pre-mounted when bought the boat.
@jeffghigo8128 Жыл бұрын
Nice job wearing that up. I have a question for your power cable did you hook the positive and -2 your ignition switch switch or directly to the battery not sure what to do there thank you.
@sixfivefishing1528 Жыл бұрын
Jeff Ghigo. Tanks for watching. My boat came pre wired with a power to my auxiliary switch wires ran. So I just hook up to that wire and I could power off and on with my auxiliary switch. That how I power mine. Hope this was helpful. And sorry it told me 2 days to get you an answer.