No Effects in your Audio Interface? No problem.

Рет қаралды 2,829

Күн бұрын

Пікірлер: 27

@MikeBrayton 7 ай бұрын

Love this concept. It never occurred to me. I've always just put a reverb on the channel itself at 100% wet, then removed it later. Problem I have is I need compression when I sing. So I just get my buffer size as low as possible, enable that button, I forgot what it's called, that turns off all your high latency effects, and put cubas's compressor and roomworks SE directly on the channel with the reverb mix at like 20%. Or sometimes I just use the mono delay. It works well. This does require a more modern computer though with the proper power.

@mansosound 10 ай бұрын

yes thanks, and its amazing how cubase changed (pre/post) that lil 'fader slider' to that lil 'half moon' after the SX version, NOT! Now I alway's have to think. When opdates are not always better

@DesperadoStudios 9 ай бұрын

It’s not that you avoid the latency by using this technique, the latency is still the same. It’s just that when the signal pass through a 100% wet effect the latency acts as a predelay and you can’t hear it. You could put the effect as an insert on the record channel as well, set it to 100% wet, push the monitorbutton and the channelfader would then act as a “reverb amount fader” just like the send level does in your example. But the signal goes in to your interface, gets recorded and are sent back out to the headphones in both scenarios so the latency is the same, just masked by the reverb.

@Meresatgurupyare 3 ай бұрын

Thanks Man, you made a very to the point video much needed on this topic, I haven't however tried that yet but thanks for creating this video, I will try to this

@jakeah1175 Ай бұрын

Amazing skill at explaining - thanks!

@You4Final 10 ай бұрын

That´s great... I have an RME UCX with DSP FX inside, but I really don´t like them. With this solution I´m far more happy! Thanks a lot

@yantra6365 8 ай бұрын

Nice one Steve, you are doing a great job on this channel. Its easy to understand your posts, great use of graphics and entertaining and informative at the same time.

@Featherlightstudio 8 ай бұрын

Thanks brother, I appreciate it man. Love the stuff your building over at Yantra as well my friend!

@yantra6365 8 ай бұрын

Maybe down the road you can do a “Am I Committed?” Episode, talking about committing eq, compression, fx etc while recording vs after the fact in your daw or hardware setup, might be a good one for ya! :)

@yantra6365 8 ай бұрын

@@Featherlightstudio thanks Steve, sometimes the efforts of an artist goes unnoticed, until its noticed of course :)

@Featherlightstudio 8 ай бұрын

@@yantra6365 Great suggestion!

@LeopardBull5trik3 10 ай бұрын

Excellent video Steve, thank you 🙏

@fernandoortegacomposer 10 ай бұрын

AMAZING TRICK! Thanks a million...

@KenFoxmusic 9 ай бұрын

what if you have a focusrite clarett+ and there is no "Direct Monitor" option? lol

@Featherlightstudio 9 ай бұрын

Works the same you just have more mix options with the Focusrite Control Software that controls your Clarett+

@FRANKRICECOLD209 6 ай бұрын

So It Would Not Work With Auto Tune Pitch Correction Plugin ? Thanks And One More Question What If You Audio Interface Does NOT Have a Direct Monitoring Button And The Direct Monitoring Button Is Grayed Out ? I Have Been Trying To Figuer This Out Foreve

@Featherlightstudio 6 ай бұрын

Most smaller interfaces have either a Direct monitor button OR and Mix knob that does the same thing but gives you more mix control. Or they have a software control panel that allows more flexible routing options but produces the same result.