NO MORE WATER IN THE BILGE ! Installing a dripless Shaft Seal

[@tetraskele9621]

Wonderful to see a woman doing this sort of engineering. Bravo! I am installing a PYI PSS tomorrow, so thanks for the inspiration! Dorian (Coos Bay, OR)

[@boatlover8856]

Great video ladies!! WTG taught me a lot

[@dreamwavemarine9346]

🙋🏻‍♂️. I own a boat repair business in Los Angeles CA. I’m also rebuilding a Catalina 38. I love networking with new boaters and helping them on their journeys. I started with little to no support a few years back and know how, up and down owning a boat can be.

[@AdventuresofHappyOurs]

Great job! I plan to replace my old PSS shaft seals as they are coming up on 17 years old. You video will help! Thanks.

[@LandandSeawithKee]

Awesome good luck hope it goes smoothly!

[@andrewlawrence9920]

My PSS seal on my Contessa 26 I bought two months ago is drip drip dripping. I burped her and because I was on a mooring I went"Shit " as water flooded out. I was thinking, "Oh my god why can't I just change to an old stuffing box so I could fix her while on water." Now, I got her back and breathed a sigh of relief when the water stopped and the dripping got lower, it worked that was good, but through the night I woke every time the bilge pump went off , she went off about eight times a day. Now, I must mention, there was no solar on the boat when I bought her and the battery was showing 11.30 so she was dead and I had to leave my pretty contessa for another three weeks before I would be back on board. So, I bought a new battery ,a deep cycle and a trickle solar panel. Ok she should be fine. . According to PSS I need to use a bit of rag and or 8oo sandpaper to clean the surfaces. Ok so I am going to do that this weekend, but I am going to put her on the hard for antifouling and I am going to put on the maintenance kit that Pss sells where the rubber puts pressure back on the seal. Ok, so how do I know which one to get? Ok so measure the shaft diameter and the other diameter is that it?, and can I do this on the water as I wont be on the hard until october 2022? I mean it's a little scary . I remember Tania who sailed around the world in her contessa fixed her stuffing box on water in mid flight. (I mean is there a serial number to find what kit to get or do I have to take an inaccurate mm size when leaning into my engine... Your video was a little godsend in some ways. Reading Tom Davi's reply just made me get more nervous.

[@MrYas10]

Great job with professionality .. All thanks for u

[@markmuller8829]

Great job, you killed it. Well done. Wow, what a pain that access to your engine is underneath your galley cabinetry! Hopefully, you won't need to go there again any time soon...

[@LandandSeawithKee]

Thanks Mark! I mean I didn’t have to remove it I do regular maintenance through the cubby doors and it isn’t too bad but I’m glad I took it apart to get a good look at everything otherwise I wouldn’t have found chafed exhaust hose!

[@shaynablum-hodes1798]

wow thanks for inspiration trying to do mine tomorrow

[@dreamwavemarine9346]

Looks great! Good job💪.

[@speedygonsalous9793]

Great job. Where did you haul out? I’m at Pedder bay but need to replace my Dripless shaft seal in Spring.

[@stefanhellemar4501]

Good work, i need to do this x2

[@GHanBax]

Does the shaft seal need to be water fed? Or is that as is and just used the hose as a vent?

[@matthewsilva8225]

Your maintenance videos are the best. I am doing this project this winter. My concern is getting that coupling back on the shaft. What exactly do you mean by bash.. and how did you get a piece of wood and a hammer in there to bash it on? I can't seem to find any videos of the coupling being actually put back on the shaft. Thanks!

[@LandandSeawithKee]

Hi Matthew I warmed up my coupling and the shaft was quite cold as it was early spring which helped. I lined up the shaft in the coupler and then use a wood block from outside on the end of the shaft and bashed it with a rubber mallet and tap it into place! I did small taps and went back and forth to make sure the key hole lined up.

[@matthewsilva8225]

@@LandandSeawithKee Did you have a machinist measure the inside diameter of the coupler against the diameter of the shaft? Or did you just reuse the coupler because it all seemed snug? I am assuming you haven't had any issues to date.

[@jellysmith4350]

Thanks for the video. I'd have really liked an expanded section on how you removed the coupling using your bolt trick! Where did you learn how to do that? Is there some place you can send me, to learn more?

[@keannarink9412]

Hi John I had someone recommend using a socket and some bolts on a Catalina Facebook forum so don’t have any specific links but it was pretty straight forward. Spray some PB blaster or other kind of penetrating oil around shaft. Use good quality fine threaded stainless steel bolts and go around tightening in a circle!

[@jellysmith4350]

@@keannarink9412 thanks so much! Bit daunting, but let's see how it goes...if nothing else, I find taking things apart, a great way to learn how everything works. And a great way to break things, of course 😅

[@TroyaE117]

These bellow-like shaft seals are fine until they perish. Give me an orthodox stuffing box any day.

[@2299jsimon]

Well done...

[@chupapimunano.1740]

Where can i buy this shaft seal online¿

[@gregoryclark3870]

well done 😊

[@lausagne4764]

great video, thanks a lot

[@tomdavis3038]

When it wears you’ll wish you had a standard stuffing box. I’ve seen 2 yachts sink due to failed dripless seals. There’s a difference between dripless and maintenance free. You’d also be surprised how many engines are either misaligned or the builder used junk cheap engine mounts Cheers

[@j.saavedra1502]

I have the same PYI shaft seal on my Pearson 33-2 running a Yanmar 2GM20 diesel. it's been operating reliably since it was installed in 2007. if you like the maintenance hassle of a traditional stuffing box, you should stick with that.

[@andrewlawrence9920]

@@j.saavedra1502 My PSS seal on my Contessa 26 I bought two months ago is drip drip dripping. I burped her and because I was on a mooring I went"Shit " as water flooded out. I was thinking, "Oh my god why can't I just change to an old stuffing box so I could fix her while on water." Now, I got her back and breathed a sigh of relief when the water stopped and the dripping got lower, it worked that was good, but through the night I woke every time the bilge pump went off , she went off about eight times a day. Now, I must mention, there was no solar on the boat when I bought her and the battery was showing 11.30 so she was dead and I had to leave my pretty contessa for another three weeks before I would be back on board. So, I bought a new battery ,a deep cycle and a trickle solar panel. Ok she should be fine. . According to PSS I need to use a bit of rag and or 8oo sandpaper to clean the surfaces. Ok so I am going to do that this weekend, but I am going to put her on the hard for antifouling and I am going to put on the maintenance kit that Pss sells where the rubber puts pressure back on the seal. Ok, so how do I know which one to get? Ok so measure the shaft diameter and the other diameter is that it?, and can I do this on the water as I wont be on the hard until october 2022? I mean it's a little scary . I remember Tania who sailed around the world in her contessa fixed her stuffing box on water in mid flight. (I mean is there a serial number to find what kit to get or do I have to take an inaccurate mm size when leaning into my engine... Your video was a little godsend in some ways. Reading Tom Davi's reply just made me get more nervous.

[@SoItGoesCAL34]

You mentioned a vent. I'm confused... isn't the nipple connected to a water hose to lubricate the shaft? Where does the water come from? A water hose? HELP. We bought a bought (owner died) and the hose is not connected.

[@LandandSeawithKee]

On most sailboats this is just a vent led above the water line to burb air out. On powerboats this needs to be connected to a water source for cooling.

[@sailinggreenpearl2571]

Great video, i have to do mine, thx

[@sreynolds3705]

Great video! Thanks. Just changed mine this winter. Deja Vu

[@LandandSeawithKee]

Thanks :) such a nice upgrade from the leaky stuffing box!

[@SteveWrightNZ]

Dont use stainless bolts on driveshafts. They are brittle and will snap off without warning. You want about grade 5 fine, and torque/turn them into their elastic region.

Hello you! I am from Vietnam, can you help me buy gearbox for my boat

[@Arg-hs6vf]

감사합니다 잘보고갑니다 korea

[@daviddiscenza3187]

Undo bolts, remove boat.

[@stevenmarrone1526]

Want a sailing partner?

[@williamturner1517]

Pay attention, Steve.

[@ronm3380]

@@williamturner1517 haha Steve was the one always looking out the window at school dreaming.