Portable Satellite Meter - V8 Finder by GTMedia for Free Satellite TV

[@CanuckHam]

I just got one of these! They work really well! I have a portable setup now using a small shaw dish and a tripod and one of these handhelds. I was watching a football game while out camping on a rainy day.

[@NorthcoasterHobby]

Sounds like a good portable setup. I just put out a video about going off-grid with free satellite TV. Thanks for watching!📡 kzbin.info/www/bejne/bqmrZGSabb5patU

[@DJSubAir]

I like your push on connector idea too, typically though I leave a short coax jumper with a barrel on the end and only ever change the barrel that wears out.

[@glennchamberlain5056]

Great video. I picked one of these up this summer. Was getting frustrated with the low signal when I was sure I had the dish aimed properly. Will try the blind scan like you suggested next time. Had it working other times with no issue. I have a portable set up with a tripod and an old shaw dish and also have a 90 cm dish that I swap back and forth just to see what I can get. I can’t leave it setup as our townhouse condo corp has a rule about installing a dish. I am basically practicing setting up the dish and finding channels so I can take it camping to supplement OTA reception. The fun is in the hunt!

[@NorthcoasterHobby]

Searching out new channels is definitely the best part of the hobby! Thanks for watching!📡📡

[@tomthumb5688]

Hi For those that are going to use a motor ( seals) yes they work and work well the only drawback is the motor…runs the battery down quickly . The best way is unfortunately to drag out a tv and hard wired to wall plug satellite receiver . You can try running a hdmi cable from meeter to hardwired satellite receiver if video comes up.

[@NorthcoasterHobby]

Great point!

[@fixingandmore4776]

Thank you for this helpful video. Can you tell me why after adding new transponder like you explained from minute 9 in this video and after press SAVE (( It is not saving )) !! When I shift to another Satellite from satellite list all new transponders gone !!! May I know why? Thank you

[@NorthcoasterHobby]

I'll look into this.

[@fixingandmore4776]

@@NorthcoasterHobby Waiting for you. Thank you.

[@DJSubAir]

I wonder if I should purchase this to coincide with my superbuddy meter to do blind scans after aiming with the superbuddy

[@NorthcoasterHobby]

I tend to use my SatHero 400 meter more, but this one is a good secondary satellite meter for me. Especially for the portability, with vehicle charger included, etc.📡

[@DJSubAir]

@@NorthcoasterHobby thank you :) have a good day

[@NorthcoasterHobby]

@@DJSubAir You’re welcome, thanks for watching!📡

[@edwardchamberlain7858]

Hey Robbie, thank you so much. If it wasn't for your instructional videos I would never figure this thing out. Can you please tell me the polarity of the AC adapter. I've misplaced the original and there are no specs for it in the manual.

[@NorthcoasterHobby]

Thanks for watching my channel. Glad the videos are helpful. My first name is Patrick. You were probably thinking of Robbie Strike (a great channel for satellite and tech stuff). The adapter is 12V 1.5 amp, polarity is center positive. Thanks again for watching!

[@edwardchamberlain7858]

Thanks for getting back to me "Patrick", Sorry about the mixup. I found the original adapter, and have now started labeling them. Something I should have been doing many years ago.

[@hrh2092]

Does anyone know what is "Loop Search" all about? What does it do really? How does it help?

[@SteveStoltz]

I just got one of these last week. I recently bought an fta setup and dragging a TV and receiver out to where the dish is every time I want to try a different satellite was impracticable. Its well worth the money in time saved in my opinion.

[@NorthcoasterHobby]

Yes, I agree. Worth it for sure. Thanks for watching!

[@alikara7231]

Why is 30 West Hispasat satellite not on the list? 2021 updated software installed. After 24W, it switches to 37.5W satellite. Is there a solution to this?

[@NorthcoasterHobby]

You can add in a satellite.

[@nickmalinski8011]

I have directv can never find the signals for fta have lots of dishes lol really want some fta is ses 101 the same satellite my directv uses 99 101 103 is 101 and 103 ses? I have no luck getting 97w etc thinking about a ku band motor I have a 39" dish also do I have to use it for 99 fta? How many channels can a shaw dish get on 97w

[@NorthcoasterHobby]

The 39' dish will work great for free satellite TV. DirecTV channels are all encrypted pay channels. You should pick up 99W with it no problem. if your dish is off even a fraction of an inch (a few mm) you will lose signal. Here is a video I made about 97 W a while back: kzbin.info/www/bejne/eHS2aYislLN2fsU

[@ima4916]

Is KaKu band, I believe they are encripted

[@iceman382]

Can you tune in a satellite and see the video as well as "signal strength" and "quality" at the same time? I find that fine tuning a satellite with the ability to see the TV picture as well as signal strength and quality at the same time helps immensely.

[@NorthcoasterHobby]

I just had a chance to look into this. Pressing the ‘Info’ button when you’re watching a TV channel on the meter brings up transponder information, as well as signal strength and quality, but it takes up most of the screen and you can only see the edges of the channel. There doesn’t seem to be any other way to make more of the channel visible and view this information. I also have a SatHero 400HD that allows you to see the channel with the signal strength and quality flanking the channel on the sides. Allows a clear view of the channel and the signal information.📡📡

[@davidakingbade2874]

@@NorthcoasterHobby HI NH, Can you do a review of your sathero HD finder compared to gtmedia finder. Thanks man

[@NorthcoasterHobby]

@@davidakingbade2874 I plan on doing that soon.

[@davidakingbade2874]

@@NorthcoasterHobby Great. Looking forward to watch it.

[@randallhutton5842]

Will these work with the dish sats of 110 and 119 on the western arc or the 61 and 71 pn the eastern arc?

[@NorthcoasterHobby]

Yes, they should work with any satellite.

[@pedrocavasos100]

Hello NCH how are you doing today ....I have the same meter it was complicated at first but finally figured it out also I have a amiko mini 265 but I think I installed the wrong update because all my North American sats disappeared and a bunch of European sats popped up any suggestions thanks

[@NorthcoasterHobby]

You might have to enter the NA satellites manually. That’s what I do on all my receivers. I think a lot of satellite receiver updates are really meant for Europe viewers. This meter is pretty decent for the price. Thanks for watching!

[@W.S.H.B]

Hey just got finished watching your video on the handheld sat finder device and wanted to know if you could receive FTA channels on this device. I also noticed in the video that there was a radio feature, does it also receive satellite stations,fm,am?

[@NorthcoasterHobby]

It’s made for receiving FTA satellite TV and radio channels. You can also listen and watch on it. It does not receive FM or AM signals, however. Thanks for watching!

[@randywood8658]

How can you unlock paid channels or can you😊

[@NorthcoasterHobby]

You’re asking the wrong person.☺️

[@randywood8658]

@@NorthcoasterHobby oh ok 👍 I understand

[@MakgataBrummer]

Where can I get this one I m situated in Limpopo province my nearest town is Burgersfort?

[@NorthcoasterHobby]

amzn.to/45JNSs1

[@JohnAbblah]

Pls mine has the 13v18v blue light on what do I do

[@NorthcoasterHobby]

@@JohnAbblah That’s what it’s supposed to do. It’s for polarity switching. 13V for vertical and 18V horizontal.

[@DJSubAir]

Does it do h.265?

[@NorthcoasterHobby]

Hi DJ, sorry for the delay. I wanted to test this out myself. I scanned in the HEVC channels on 116.8 West KU Band, and the sound comes through but no picture, so I’d say it won’t decode the video signal on H.265 channels.

[@PezCandyDispensers]

Do you need to pay for satellite to get the channels?

[@NorthcoasterHobby]

There are no subscription fees. Just the cost of the equipment.

[@akhlaqhongkong6439]

Best video ever I learn a lot becuse already got from long time a go but don't know how to used.thanks a alot god bless you

[@NorthcoasterHobby]

You’re welcome, thank you for watching!

[@lentomies]

Hello NorthCoaster, Firstly, I want to extend my heartfelt gratitude for your educational and enjoyable videos. Your contributions to the community are invaluable, and I appreciate the time and effort you put into creating such content. Now, onto my question: I recently watched your video on the V8 Finder by GT Media and am considering purchasing a meter to locate KU and C-band satellites. I have a specific scenario in mind and would love to know if the V8 Finder can meet my needs. Let's say my dish is aimed to receive signals from 97 West, but it's not perfectly aligned yet. Does the V8 Finder offer a spectrum display that can help me gauge whether I'm getting closer or further away from the satellite? I didn't see this feature demonstrated in your video, so I'm leaning towards the idea that it might not have it. If you could provide some insights or even a demonstration, it would be incredibly helpful. Thank you once again for your time, and I hope you have a fantastic weekend!

[@NorthcoasterHobby]

Thank you for the kind comments, and for watching my videos. I will check into this and get back to you.

[@NorthcoasterHobby]

I had a look back- I outline the spectrum display at 9:46 in the video.

[@taganize]

@@NorthcoasterHobby How the heck did I miss that? SORRY! I got to ask will the spectrum still work as your panning the skies slowly for satellites? Or do you have a video demonstrating how this feature is used outside to detect a satellite not yet connected to? I need a device that can do this to make life easier.

[@NorthcoasterHobby]

@@taganize No need for apologies. I personally prefer using a strong transponder on the satellite installation screen (with signal meter) to adjust a dish. Once that is locked, a blindscan usually brings in the other transponders.

[@taganize]

@@NorthcoasterHobby Thanks again for your response! I really appreciate your support! I am writing to express my interest in the spectrum analyzer you have presented, specifically its utility in assisting with satellite dish alignment. My experience with aligning a dish to locate, for example, the 97 West satellite was laborious and time-consuming, taking up two weekends of trial and error. Despite having a general understanding of the direction in which my dish needed to be pointed, I found myself scanning horizontally and vertically in the cold weather of January, with limited success and frozen fingers. My primary concern is to understand how effective the spectrum analyzer is in expediting this process. From what I gather, the device should display fluctuations in signal strength as one moves (pans) the dish in the vicinity of the targeted satellite. These fluctuations could serve as invaluable indicators, suggesting whether one is close to aligning with the satellite or needs to adjust the dish's elevation. I have seen online demonstrations where individuals were able to locate their desired satellites in a matter of minutes, specifically less than five minutes. Such efficiency is highly impressive and desirable. Therefore, I am keen to know if the spectrum analyzer you are offering can provide similar capabilities. Accurate and quick alignment is crucial, as even slight deviations in elevation can make a significant difference in signal reception. Once a viable signal is obtained, I understand that the subsequent steps, such as fine-tuning and scanning, become relatively straightforward. However, the initial alignment is often the most challenging part, and any tool that can simplify this process would be of great value. I look forward to your response and any additional information you can provide about the spectrum analyzer's capabilities in aiding satellite dish alignment.

[@RobertoCarlos-ux6mg]

What is the name of this connector please

[@NorthcoasterHobby]

Which connector? The push on RF connector? I made a video about it: kzbin.info/www/bejne/i2KuqHmul7WeiM0

[@lawrencejd8935]

Is this device came with remote control?

[@NorthcoasterHobby]

There is no remote control.

[@lawrencejd8935]

@@NorthcoasterHobby so can we add one? As universal remote

[@NorthcoasterHobby]

@@lawrencejd8935 No.

[@DXingSlovenija]

I wish theese would do analog as well (but sadly analog was gone before theese started to exists :( ) BTW: is the software updatable and open source? Also can you somehow hook a smart card to this to watch encrypted content? Also does it have some compass or similar to help you align to satelite (point the dish the right way)

[@NorthcoasterHobby]

No compass on it that I can see. My channel focuses on free unencrypted satellite TV channels only.

[@k.z.9250]

Where it get. Is it available on ind.

[@NorthcoasterHobby]

I bought mine on eBay.

[@wassi512]

price kaya hae aur magwana ho o kaisay milaygha

[@NorthcoasterHobby]

amzn.to/45JNSs1

[@AgbonahMatthew]

Please I need this finder

[@NorthcoasterHobby]

@@AgbonahMatthew amzn.to/45JNSs1

[@Muzovugift]

Can gt media work in Africa

[@NorthcoasterHobby]

It should.

[@danutaish]

My old Easy sat finder performs a lot better. I would not recommend the GT brand. It takes twice as long to find satellites it is a nice video I like the TV feature

[@NorthcoasterHobby]

Thanks for the feedback, and for watching.

[@danutaish]

I got it working now. I had to reinstall the firmware it looks like the numerous problem I had with the device is fixed. It was auto rebooting. 3 LNBs 95w ku galaxy19 and 103w 😁😁😁 I also added 87w ,125w in early December

[@NorthcoasterHobby]

@@danutaish Good to hear!

[@capajserbia235]

Can it play tv channels?Main stuf you cant see in this video.

[@NorthcoasterHobby]

Yes it can, it has a built in TV screen. I won't show copyrighted material in my videos, though.

[@lacey397]

I just got the same one in the mail looks like it's really good...it was 71.00

[@NorthcoasterHobby]

Good price, hope it serves you well! Thanks for watching!📡

[@dogdazetravellergarrett1367]

Appreciate the video tutorial..... Thanks 👍

[@NorthcoasterHobby]

@@dogdazetravellergarrett1367 you’re welcome!

[@tomthumb5688]

Another up date on gtmedia gt combo been playing around with the gt share apk and over all works good but it is WiFi so sometimes one might have issues just like fpv on drones when it comes to WiFi it depends on connection, works on Samsung-lg- iPad it may not work on older tv boxes . Works ok

[@NorthcoasterHobby]

Thanks for the update!📡📡

[@mheyeng]

nice sir...can i have your satelite meter sir?🙏🙏🙏

[@NorthcoasterHobby]

Sorry I need it!😄

[@mheyeng]

if ever you will buy a new one sir..

[@selamdehane7899]

Hello I found your video while I was trying to figure out how to get a specific channel to watch here in the United States. Can you please help me with this? I am willing to pay you for your time. Thank you!

[@NorthcoasterHobby]

What channel are you looking for?

[@ken2400]

I just used mine today.

[@NorthcoasterHobby]

Nice. Sure beats dragging a TV and receiver outside! It’s handy to have.

[@hassnainalam8337]

Kia price hai

[@NorthcoasterHobby]

About $76 USD

[@brahimfadili-mr8wc]

how much please

[@NorthcoasterHobby]

Check eBay or Amazon for current prices.

[@thrillington2008]

I might get this with my tax refund. My interest of getting a v8 finder has resurfaced recently.

[@WolfCaesar-w6x]

516 Zieme Passage

[@planca3430]

if your dish is aimed correctly im sure your meter is giving you all this info but not when your dish is not aimed right. that is my problem my dish still needs fine tuning. ive found its not as easy as it seems. shooting a gun with a scope is much easer than aiming a dish.

[@NorthcoasterHobby]

I replied to your other comment.👍

[@wassi512]

plz tell me

[@NorthcoasterHobby]

amzn.to/45JNSs1

[@prashantmulay7033]

Mrp

[@NorthcoasterHobby]

I paid $87 USD.

[@hrh2092]

There are different brands, GTMEDIA, CENPEK, etc. Is there any difference or anyone will do?

[@NorthcoasterHobby]

I like this device, it does a pretty decent job however, the signal metre is not particularly accurate. It seems to read low, usually the signal level tops out in the low to mid 70s, even if the signal reads much stronger on my set top box receiver. It’s still does a decent job of aiming a satellite, though I am personally a big fan of the SatHero portable satellite metres- however, they seem to be harder to find these days.

[@hrh2092]

@@NorthcoasterHobby This is by the way original finder 1, there is now a finder 2, a finder max, and a finder pro.

[@syedmudasir693]

Hi

[@NorthcoasterHobby]

Hello

[@Alterego808080]

Thanks, due to your video and seeing that it reads the signal low (not exact) I have cancelled my order of this device. Thank you!

[@NorthcoasterHobby]

@@Alterego808080 Glad my video was helpful. That issue aside, I find this meter to be useful.

[@Alterego808080]

@@NorthcoasterHobby Thank You Sir :) I have ordered one again 🤣It seems like a proper tool when I saw your video one more time. Best regards and greetings from Denmark!

[@NorthcoasterHobby]

@@Alterego808080 👍