THERMISTOR || NTC 5D-15 NEGATIVE TEMPERATURE COEFFICIENT
Пікірлер: 26
@JaykeSapalaran-iq3qs Жыл бұрын
One of the best Great video tutorial 👍♥️🇵🇭 Thank you for sharing your knowledge ♥️
@electroncomstudio6370 Жыл бұрын
Thank you Sir
@Sohagroyofficial2 жыл бұрын
Best of luck 👍. Carry on
@fritzj68032 ай бұрын
Great tutorial. My NTC thermistor is marked differently with the number 16 in the middle and 2011 underneath. There's no letter "D". I'm trying to figure out how many ohms is marked on it?
@zaidanbaa18 ай бұрын
Thanks for this video❤
@electroncomstudio63707 ай бұрын
Thanks for watching
@solo95768 ай бұрын
Thank you.
@ThomasBurns Жыл бұрын
Thanks for this video! Does "8L10 10002" mean it acts like a 8 ohm resistor at room temperature? What does the "L" mean?
@MENASI-VISIO11 күн бұрын
L it's a tolerance at 15%
@itsme_sauravraj7 ай бұрын
how do i know at what resistance what will be temperature? are there any graph?
@opravduchytradomacnost Жыл бұрын
Thank you, now I missing answer for the diameter differences, why some are bigger?
@colin5064 Жыл бұрын
Hi, l enjoyed the video clear explanation of NTC type however l have a PTC Thermistor in a circuit which is a blue ceramic disc type. I cannot understand what the item reference markings are referring to,it is marked PTC C 840 which l conclude to be Positive Temp Coefficient / Ceramic. then there is a further reference number 0317 underneath the C840. Do you have any help to offer as to the meaning of these ref numbers marked on this item.
@electroncomstudio6370 Жыл бұрын
Thanks for watching. I guess 0317 figure underneath the C840 does not affect your design though I'm not sure. C840 is necessary as it is the type of Thermistor set as standard and it has an equivalent Electrical Specifications. You may also find C830, C850, C860.
@riteshkukreti91919 ай бұрын
Sir NTC or PTC me koi particular value hoti h ya kisi bhi value ka lga sakte h
@sublimeelectrons86996 ай бұрын
sir what if my NTC 100D-9 has cracked a little bit but it still decreases resistance based on the test procedure you showed. Should I still replace it?.. By the way fuse got busted and 2 diodes IN4007 got shorted on the bridge, is it logical to conclude that this NTC is affected due to too much heat apparently from excessive current?please reply..😊
@walker55able2 жыл бұрын
Thank you I have changed 2 in a power supply
@electroncomstudio63702 жыл бұрын
Congratulations. Great job.
@midrone4349 Жыл бұрын
Ohh, then You are taking chances. There may be 3 options for the correct - as I wrote about.
@yohanrathnayaka80968 ай бұрын
Thank sir
@electroncomstudio63707 ай бұрын
Thank you for watching
@user-up9co6wo3g7 ай бұрын
okay lang po palitan ang value ng thermistor or hindi
@jhoelito158 ай бұрын
tks 1000
@electroncomstudio63707 ай бұрын
Thank you for watching
@noslidemais Жыл бұрын
@robaduba80954 ай бұрын
Pwede po ba eh check yan sir kahit naka connect pa po sa board niya?
@electroncomstudio63704 ай бұрын
Thank you for watching. Yes you can but make sure your device is not connected to power, that there is no presence of voltage for safety.