lol 19:22, while you are saying that, there's a screw stuck in the graphic card.
@pavloskaramanis22072 жыл бұрын
Thank you for your video! I got the MC1 for my 970 Evo Plus 2TB, desktop w/2 fans front & 1 rear. Without cooling, the controller reached 94C with Crystal Mark. With the MC1 it went down to 65, same room temp. Very impressive!!
@stevienashville534111 ай бұрын
For the first step of installation which side of the sdd did u have facing up I can’t tell which side should be facing down against the thermal and which side should be facing up?
@pavloskaramanis220711 ай бұрын
The side with the factory sticker should be up, it is the side you see after you place the ssd to the base of the MC1@@stevienashville5341
@mihaitechtips69986 ай бұрын
The reason the MC1 PRO is taller is because it will allow double sided drives with chips on both sides , amazing video experiment that you have done
@BillyBobDingledorf Жыл бұрын
Don't unplug your power supply. Doing so will remove the ground from the motherboard. If you must unplug, run a ground strap from the case to a ground.
@JayzBeerz3 жыл бұрын
This is great as long as your motherboard doesn't have a heat shield installed already.
@overclockersclub2 жыл бұрын
Right, you might have to use one or the other.
@thierrybo6304 Жыл бұрын
I was disappointed when i wanted to use my motherboard heatsink. It was designed for a 22110 m2 drive and the head of the screw prevented me to apply it on the drive.
@JayzBeerz Жыл бұрын
@@thierrybo6304 just move the post dude.
@High.on.Life_DnB3 жыл бұрын
If you're considering one of these for your PS5, don't get the MC1 Pro version, it won't fit and you can't get the cover back on.
@billanten78623 жыл бұрын
I just did and it fits you just have to put the cover to the holes on one side and just push down the other side with your fingers and then just put the screw and turn it , the cover is flexible and holds well enough.
@adamsam93322 жыл бұрын
@@billanten7862 no dont do that if you force it the cover will touch the cooler and it will increase the heat
@Stance19882 жыл бұрын
@@adamsam9332 Durh, the cover already increases the heat, it makes it an oven. Dont use that junk.
@BeamerTime354 Жыл бұрын
Have 2 drives with the mc1 pro on both and never any problems. Well worth the $15.
@dezmondwhitney1208 Жыл бұрын
This was Thorough. Excellent. Many Thanks.
@theovandenberg46823 жыл бұрын
Very thorough test, thanks for that. Is there a fastener poking out of the cooling fins on the side of your graphics card?
@overclockersclub3 жыл бұрын
Wow!!! Yes it is! I’ve been looking for that for over a week and couldn’t figure out what happened to it! Thanks so much!
@overclockersclub3 жыл бұрын
It took me a moment to figure out what you were talking about. Then I looked on the end and, ooooohhhh…
@theovandenberg46823 жыл бұрын
@@overclockersclub Yes like you mentioned in the review: Be careful with fallen fasteners.
@overclockersclub3 жыл бұрын
@@theovandenberg4682 I’ll make sure to point that out in the next review and give you credit!
@causticlaurent2 жыл бұрын
Congrats for your detailled test :)
@TurkOglu19902 жыл бұрын
While sandwiching the drive, to set it good on can u slide alittle to line up wont thay harm the stickyness of the cooler? Hope u understand what i say sir.
@Pyromaster_2 жыл бұрын
Very informative!
@drkelvinchua4517 Жыл бұрын
Thank you very much for such a detailed video. It is really helpful!
@Bretzelbueb2 жыл бұрын
Im a liitle bit confused by that screw in your graphics card. The Video was pretty interesting.
@niyamimbi11792 жыл бұрын
Thanks for the vid. Nitpicking abit here, though: if youre using C as temp on the benchmark, why not change it on the ambient thermometer as well(or the other way around?
@RudikArt3 жыл бұрын
thanks a lot for detail review!
@abacaxiveer3 жыл бұрын
Eh, cool! :). Are these likely useable with a PCIe adapter card for M.2 drives?
@overclockersclub2 жыл бұрын
Should be ok but it might depend on what is in the next slot.
@spaceman79152 жыл бұрын
10:58 & 18:52 why is there a screw in your video card cooler fin? LOL
@overclockersclub2 жыл бұрын
Yeah - I was looking for that screw. Then someone pointed it out in the comments (scroll down a little). Yep - found it!
@laurelhardytv3588 Жыл бұрын
Can i put it on a Asrock B550M HDV?.
@klipk7296 Жыл бұрын
tbh I'm surprised the factory/motherboard heatsink did so well, they make very little effort to increase surface area on those
@iflewover Жыл бұрын
Just what I needed, thanks. I want to know how much is the deference between the Bequiet heatsink and stock m.2, cause I want to get one for my PS5. It performed really well.
@Gogargoat Жыл бұрын
What's that screw doing in the rear fins of the graphics card? visible at 18:55
@Arcadia-Pearljam3 жыл бұрын
I lost 10 degrees with the MC1 Pro on my B450
@overclockersclub3 жыл бұрын
Impressive!
@brnerproduction47393 жыл бұрын
Thank you for this helpfull video!
@stevienashville534111 ай бұрын
For the first step of installation which side of the ssd(mine is 980 pro) do u have facing up I can’t tell which side should be facing down against the thermal and which side should be facing up? The side that says 980 pro or the other side of ssd that says Samsung ssd
Жыл бұрын
Whats with the screw stuck between graphic card cooler? 😂
@jaimiepotts3 жыл бұрын
I'm currently looking for a cooler for the SSD on the rear of my motherboard. Space is tight so the more low profile the cooler is the better. Would you be able to tell me the total thickness of the coolers when they are fully assembled with an SSD inside of them? I've been trying to find the dimensions online but can't find anything reliable
@nicolajsvendsen5562 жыл бұрын
Thank you for the info
@kimuranaito1493 Жыл бұрын
The 1st one was PRO...then the other one should be NOOB🤣
@rigidhammer7376 Жыл бұрын
what software you use to test?
@ReodorF1 Жыл бұрын
I see everyone are keeping the sticker on the ssd wouldnt it be better taking it of before installing the cooler?
@thierrybo6304 Жыл бұрын
I read many comments saying the stickers are not only just stickers for warranty, apparently some (most ?) of them do some light heatsink
@klipk7296 Жыл бұрын
They aren't normal stickers, they are usually thermally conductive so they can spread heat
@astigrockonph2 жыл бұрын
I got mine for cheap 2 dollars china brand. Almost the same performance, mine is max temp 51° room temp 27°c. I tasted multiple times but i came to the most effective one. Putting thermal pad to the controller chip and leave the nand flash chip vacant and not touching the heat sink. I actually test that the controller is hotter than the nand flash so i didn't need to put the thermal pad and heat sink on the ssd.
@BillyBobDingledorf Жыл бұрын
SSDs like to be warm, but not hot. Don't over cool. If you have a relatively powerful SSD, the factory heatsink is sufficient. If it doesn't come with a heatsink, something like the MC1 is plenty. Yes, there are users that are constantly moving huge amounts of data and are stressing the SSD for hours. These folk want the best cooling they can get. For the rest of us, including gamers and non-pro video editors, basic cooling is just fine. If you're a light user or have a moderate SSD, no heatsink needed. Seriously, don't over cool. You'll shorten the life of your SSD. There are conditions where the SSD is boxed in, with no airflow (e.g. PS5), where anything you can do to give it some cooling is a good thing.
@Khoragg2 жыл бұрын
If i use one for a second ssd in the m2 slot beneath my graphics card it probably won't fit being so high ye? Like the card will not click in cuz of the height of the ssd with the cooler? Did some1 try that? Guess thats why there's no factory cap there in the second slot. Edit: i use msi X470 pro carbon motherboard, my 2nd slot is not beneath the gpu but like exactly under it.
@pedroferrr141211 ай бұрын
I have two WD_black SN770 2TB installed in my system. The one connected to the cpu, was using the MB Heatsink, just like the one in the video. But it was reaching 89ºc in the nand, when copying. The other one connected to chipset, is using one from a Chinese manufacture, the cost me 15€, and the max temp is 66ºc. So i bought another one, and the temp changed to 66ºc max, idle is 56ºc. The funny thing, not so funny is that the one connected to the ChipSet is faster than the one connected to the CPU, even that the speed of the bus is the same in both 4x PCIE 4.0, and the GPU is at 16x 4.0.. I don´t understand how, it should be the opposite.
@mohamedsamir5644 Жыл бұрын
Can this be intalled in alaptop? Or it will be too big for space inside?
@overclockersclub Жыл бұрын
Not really - I have not seen any laptop where this heatsink would fit.
@winkawak Жыл бұрын
will this mc1 pro fit the mini itx mobo strix z690i?
@sw09312 жыл бұрын
very useful video
@krisg822 Жыл бұрын
19:25 talk about loosing parts....there us a screw in your graphic cards heatsink - where it's not supposed to be 🤣🤣
@kevindewilde79703 жыл бұрын
I use the mc1 for the ps5
@keancv2 жыл бұрын
Love the video, gave you a thumbs up. As politely as possible, there are ssd coolers like yours that have their own laptop fan. What you have is good but not really a permanent solution
@High.on.Life_DnB3 жыл бұрын
In my old desktop when I turned off the PSU the light from the GPU would stay lit for about 25 seconds or so, but with the PSU off, then pushing the on button on the desktop makes the light disappear almost instantly letting me know there shouldn't be any power left in the system.
@spilergameplayasmrgamingmo9936 Жыл бұрын
Szép teszt GG test nice bro
@andreyvesnin82092 жыл бұрын
Thank you for your test, it is exatly what i was looking for. Goog luck! Thumb up and subscribe from me!
@k03nk3.r3 жыл бұрын
Can I use a heatsink like the mc1 for the standard ssd in my ps5?
@kennyc57953 жыл бұрын
I think so but not the pro
@kiemferiway73753 жыл бұрын
What is the sizes on this heatsink cooler? L/W/H in mm please.
@kiemferiway73753 жыл бұрын
I am asking because I was wondering if it will fit in the PS5 console.
@overclockersclub3 жыл бұрын
www.bequiet.com/en/accessories/2252
@overclockersclub3 жыл бұрын
www.bequiet.com/en/accessories/2251
@Wakabatan3 жыл бұрын
@@kiemferiway7375 BeQuiet made a post on their KZbin channel stating that the MC1 would be compatible with PS5! kzbin.infoUgyx6ny0d3QhlMLMX-Z4AaABCQ