Offset Printing on the Heidelberg KORD in Super Shop 9

[@kdwslc]

Thank you for posting! That press was a huge part of my life in high school!

[@hotpuppy1]

It's been 27 years since I ran one of those. I was 21 and the guy who taught me could run 4 color stuff on it (one color at a time). The machine and he was THAT good!

[@robovermars1309]

So did I. Great press.

[@fernandovalencia3542]

Same here I learned on this press in 79. The veterans taught me well. I remember I hung a plate faster than this guy. ROOKIE.

[@brakojojo8656]

it register very well. i want to no the cost the kord machine

[@mohamedlaminecherrad4027]

That's my machine offset i work in it we have the same category of Kord and cors just size paper maximal what chenge

[@orokrakib8230]

Press it in any country

[@moun2k]

Hi, everybody, i'm searching for Heidelberg KORS or KORD Operation Manual, i just found one but incomplete, it only contains 57 pages. It will be very helpful for me. Thank you.

[@davidrowley3060]

Do theses machines need packing behind the plates. Was common practise when I ran offset.

[@stephenrichendefer8782]

More accurately, you had to mic the packing to meet the requirements of the press (for the K series and others). If running 4 color process you could vary some of the packing thickness to make up for image shrinkage. If you were careful in the amount of water running via the dampening system you could drastically reduce the amount of shrinkage or stretch.

[@inkitsolutionsltdkenya2258]

must it that one must follow CMYK when printint fullcolour

[@hotpuppy1]

Yes, if careful setup. However, start with PERFECTLY clean rollers and run yellow ink first

[@stephenrichendefer8782]

You most certainly can start with yellow. Yellow shows up as black when viewed via a blue filter. Makes getting true yellow much easier the running yellow later on in the chain.

[@nortonnewmann3711]

I always ran CMYK on the KORD 64 in mid '70s. I ran a 40" 5 color 'Berg CMYK + varnish in late '90s. But... We used a densitometer and colorbars to check laydown density. There is a spectral difference when using dry trap vs wet trap on a multi-color press. Been a long time...

[@shakeelnazeer8200]

Hey sir kia hal hain umeed hain ap fit fat ho ge so sir meri ap se request hain k please handelbarg 2 coler machine ko chalane ki full tareqa kar bata de

[@LightRoseArt]

Bayli Robinson Period.3 #25 this is neat!!..I'm nervous though to use this big tool..! O_O

[@cesarmata7367]

is perfect registry if printing 4 colors ????

[@hotpuppy1]

Yes, if your setup is careful.

[@joseoliveira7369]

Estou vendendo uma Kord 64x46 e uma guilhotina Catu 82 de boca mais 3 facas

[@arthurbuenvenida3479]

I'm operator also Heidelberg G.TO and SOLNA

[@ROCKO633]

this print machine is super small,...the new man roland 900xxl is massive 64inch,..

[@sunglobal9901]

hi

[@santoshmishra5560]

vi

[@orokrakib8230]

I want a job. Someone will benefit me. I'm a messen man

[@alvivathi5731]

FAIL YOU START WORK AFTER 5 MIN

[@evercastroaza8145]

Ese nobato ni sabe poner una placa

[@tinytasks4862]

Terrible industry to be in. 11 Years was enough for me!!!!

[@stephenrichendefer8782]

I worked in the printing industry for 25 years running everything from Multi 1250's to a KORS and loved it.