OIL & FILTER change CASE IH 75C, Ordeal NOT Ideal!

[@GradyDougless]

Thanks for doing this video! It has halved my time to change the oil. I had some tools that eliminated your bracket removal, I’ll try to send pics

[@TheLovelyPlace]

@@GradyDougless awesome! I would like to learn more about the tool you used. Thanks!

[@dalesiebert7093]

I own a 75c C also. I just changed the oil today for the first time. " Ordeal not ideal" is a complete understatement. Had the Italian engineer been standing next to me with wrenches in my hand, it would not have been a pretty picture. I took the same route you took, never again. Yes, you do need to remove the loader and toolbox. You do not have to remove the fuel filters but do not remove the side cover bracket. Next, release the electrical connection and tube that run vertically in front of the oil filter. The FILTER WRENCH YOU NEED is a cap type 93mm, 15 flute made by PT part number W54107 sold at Auto Zone for $4.00. This wrench will not fit the filter that comes on the new tractor, but fits the CaseIH replacement perfectly. It is still a very tight fight, but the hydraulic hose and the bracket will flex just enough to pull the filter out and get it back in. I must stress, again, do not remove the side panel bracket, unless the engineer is near, then by all means insert it. The oil plugs are 12mm and yes, the wrench will need to be cut to fit behind the hydraulic oil filter. Thank you so much for the video. P.S. I will never buy a Ferrari after this debacle.

[@TheLovelyPlace]

@@dalesiebert7093 lol!! Thanks man! I appreciate all of the info. Yes a Ferrari is officially off of my list now too.

[@LouisPellerin]

I have a 2014 75c and to remove the first fuel glass see thru bowl i use a 16 inch long nose plier and unscrew from underneath the tractor.Once loose,complete the unscrewing by hand and remove bowl from underneath.THe oil filter is removed by ratchet oil filter strap and it is still a VERY tight spot with that wire right next to it.I see with all those years gone by that case has NOT relocated nor made it easier for us owners.Thank you for your time and video.

[@TheLovelyPlace]

@@LouisPellerin thanks for that info. I was wondering how far this issue went back. Yeah you would think by now there would’ve been enough complaints from the service department at all of these dealerships that they would’ve done something about that. Thanks for watching the channel. Hope you guys have a merry Christmas.

[@joewilkie365]

I have my eye on a 2014 75C 1500 hours real nice shape This might be the reason it’s for sale?

[@ryang362]

Thanks for the 75C maintenance videos, they make my life easier! Note that it is actually the temperature gauge you are referring to as the oil pressure gauge.

[@TheLovelyPlace]

@@ryang362 lol after I learned that I felt a bit silly. I appreciate you watching g and I’m glad the video helped.

[@jloden8873]

Just did all 3 filters talked to the Case tec first he told me to fill the filters all way up gave a little more advice I didn't follow nor will mention he said the way they do it well after the filters went on I open blead screw pumped 300 times non stop took about 10 minutes turned over mabe 9 times and started . This works

[@TheLovelyPlace]

@@jloden8873 great job! You got this!

[@martyh299]

Sean, we had an International 140 and Ford 8n during my tractor days. I believe I could have changed the oil, oil filter, air filter and hydraulic fluid in both tractors in the time it took you to do this service. Man, you had every right to get aggravated! I just hope when the next video comes up you have the no oil pressure figured out. God was definitely with you on this one! God bless!

[@TheLovelyPlace]

Hey Marty, yes God was absolutely with me and always is with us! that was a rough one. Lol I appreciate you hanging through it.

[@andybeshear5921]

I completely filled, sealed & pressurized the fuel tank with an air compressor. With the bleed screw open, fuel ran through the system and most the air was pushed out the bleed screw. Then I cranked the starter to finish bleeding the system. The tractor started and ran. The entire fuel system holds around a gallon. Reattaching the loader on un level ground was my ordeal.

[@rickydean6544]

Wow have more patience than I have. On that 12mm allen wrench just cut it to fit between that hydro filter and oil plug. Good job, love your videos.

[@TheLovelyPlace]

Thank you, sir. I don’t know about patience but, long suffering yes! Ha ha.

[@OldAcres8690]

If I remember correctly that is a T60 socket i will have to check when I get home. I took the plug to the parts house to match the plug.

[@terrancesnyder9323]

Good morning & God bless you all

[@TheLovelyPlace]

God bless you and thank you!!

[@case85xtfan33]

The (oil gauge)as you call it is actually the coolant temperature gauge low oil pressure is only a little light directly opposite the low temperature on the temp gauge above the glow plug light hope this helps

[@TheLovelyPlace]

Thanks yes figured that out afterwards. Can’t take back video evidence of ignorance. lol.

[@justin9055]

Same set up on my New Holland 55 (basically same as your 75c both made by CNH). Instead of buying a new allen wrench I took one that was slightly to big and shaved it down slightly with a grinder with a sanding disc til she fit. Better than wasting the day for me running 45 minutes to town. Gotta wonder what these egineers are thinking when they design these tractors/ engines.

[@the_farmerYT]

Had this problem changine thr oil filter today, it was a living nightmare, still have to put the new one on, case has an unbelievable design, I honestly wonder how the case dealership would deal with this 😂 Edit: I forgot to mention that when taking off the oil filter and putting it back on, which i just got done, I had to take off the hydrolic line, and had to put it back on . . . why did case ever design this!?

[@fowlerweb]

Is there a relocation kit available to move the oil filter to another location? I'm looking at getting a used 2021 Case 75A full cab loader. Thanks for your videos.

[@TheLovelyPlace]

A relocation kit would be nice but I don’t think they have one. However, I think that the A model may be located in a different place. I appreciate your comment.

[@OldAcres8690]

I agree.

[@dfrepair1576]

Was a new holland service manager mechanic. Fuel filters are not worth messing with pay for one injector with debris. Get yourself a strap filter wrench with a ratchet . Do not stab with screwdriver makes it worst to take off.

[@dfrepair1576]

Check to see if you can purchase a remote oil filter relocation kit

[@OldAcres8690]

Can you get that from a dealer?

[@TheLovelyPlace]

I may need to stay in touch with you. lol. Thanks for the input!

[@isaacp4727]

Buddy! You have saved my ass and patience with this video. Thank you from the bottom of my wallet. 😉

[@TheLovelyPlace]

That’s really cool to hear, dude! Please explain I’m curious how it affected your choices. Do you already have a case? Were you doing service or were you contemplating a tractor to purchase?

[@isaacp4727]

I'm owner operator of a ranch in canada. I bought a case 75c last year. I've always done things myself, from cars to renovations. So when I saw ur video i figured, heres another jack of all trades, he's probably got some good tips. Pro tip though, turn the wheels all the way to the right when ur working it gives you alot more room. 😉