In this video I replace the oil pan gasket on a 1996 gmc Sierra 1500 5.0. Thanks for watching! If you have any questions let me know.
Пікірлер: 95
@therealjpoe233 жыл бұрын
Lucky you. Late 97 & 98 and up has the full bellhousing covering the Torque Converter. You had just enough room to get the pan clear. 🎯🏆
@chousubow2 жыл бұрын
Great video, I also need to change out the oil pan gasket on my 92 c1500 2wd Silverado, as it's leaking from the rear corner at the oil pan rubber seal. I was happy to see that I won't have to lift the engine up to remove the pan, I'm encouraged to get it done now. Thanks for making the video!
@nathanbishop19992 жыл бұрын
It’s a job but it can be done in a day. If you get stuck feel free to ask me any questions. Glad you liked the video!
@chousubow2 жыл бұрын
Thank You!
@keithwatson82288 ай бұрын
I just did mine. I was able to take only the passenger side of the exhaust apart since I recently changed to gasket on that side. I just moved the flywheel cover over enough to get to the nuts, and maneuver it to free the pan. I did the reverse to get it all back on. The worst part of the whole job was lining up the holes with the brackets on the outside of the pan, the pan itself, the gasket, and the block to get the bolts started. I figured the brackets are probably there to give an even pressure across the entire pan. So I couldn't discard it. Once I got that in, the rest was actually quite simple. Chevy's are awesome.
@djmidnight73662 жыл бұрын
Hey nice video you got straight to the point Good judgment
@nathanbishop19992 жыл бұрын
Thank you! I will be doing more work on the truck. I work 70 hours a week so I squeeze KZbin in when I can lol. Everything in life is pretty simple to work on you just have to take it step by step. I just take things apart and figure out how to put them back together
@ricardojohnsonthon75473 жыл бұрын
I like your closing comments.
@nathanbishop19993 жыл бұрын
Thanks! I’m slowly getting better at making videos. I like to be honest, I’m mechanically inclined but this project defiantly took a long time and required a lot of patience. I didn’t have any information on how to do it I just went under there and started taking stuff apart
@creativeminds9973 Жыл бұрын
Is there any more bolts that have to come off the pan where that cross member is blocking?
@drummmmerfish10 ай бұрын
at 5:30 to pull the pan out freely you need to pull out the wiring harness directly under the pan to make it easier. then put it back when you reassemble. also, when taking out the pan bolts, put a rag over the cross member. this is because there's a hole there and if you drop a bolt (like i did) you will have to fish it out.
@ivanrodriguez92702 жыл бұрын
Oh boy! So I have to replace the oil pump on mine but I have a 4x4 and the differential is on the way 😓 went to a shop and got a $400 quote to change my oil pump and put new gaskets! It looks like im gonna have a busy weekend!
@nathanbishop19992 жыл бұрын
You’ll get it done, it’s definitely easier with a 2wd truck. Good luck!
@javiersolis145622 күн бұрын
Wow that cheap ..
@cj81722 жыл бұрын
Love the vids on the truck. Two questions, is it totally leak-free after doing it? And will you be dropping the trans pan and changing the filter sometime soon? If you do please video it. Main reason I'm mentioning the trans pan and filter is because the trans crossmember is in the way of the rear pan bolts.
@nathanbishop19992 жыл бұрын
No leaks at all afterwards, I took the time to clean the metal surfaces where the gasket is placed. I actually just had the transmission rebuilt soon after this video was made so I will not be doing the transmission anytime soon, unless I buy another truck similar.
@ralphmitchell34352 жыл бұрын
On my 98 even with the crossmember you can still get to the rear trans pan bolts wit a socket extension.
@cristhegearmonkey10 ай бұрын
I got a 95 c1500 pickup. I'm pretty sure I have just enough clearance as well does the gasket seat properly any leaks? Seems like it'd be difficult tryna cram the oil pan back in and not move the gasket around? Get back to me imma go ahead and order the gasket
@murb2586 Жыл бұрын
i have to change both transmission and oil pan gaskets, if i took off the transmission pan, would the torque convertor cover come out without detaching the exhaust, as well is merely retightening the exhaust flange enough to reseal, is there any prep. thanks for the video and effort, grreatly appreciated
@DECIFERTHIS092 жыл бұрын
How do you get oil filter housing to line back up
@Junior-Sports9 ай бұрын
Hello, recently had a small tiny Oil Leak on my 96 Chevrolet Silverado 1500. And got the part to do this exact thing, I have some questions that I would like to ask. I’m a particularly young fellow not familiar with the in and out of mechanics, will this be a hard or difficult job to do? When I ordered the replacement pan set, it came with 4 small other pieces, where do these go? If you’re able to explain that.
@DavidinTexas2 жыл бұрын
Thanks for this, i have the same (94) Truck, Its ~ hard to find vids for Trucks this old & simple. That partial bell housing cover didnt come with my truck, so it should be easier to replace the leaking gasket ... The previous owner says he found it, at least i now know, why it wasnt reinstalled ..lol
@nathanbishop19992 жыл бұрын
Glad you liked it! I don’t blame the previous owner for not re installing it. I was almost at that point after it took me all day to install the stupid gasket lol.
@dennisdain9872 жыл бұрын
Great video. Reading through the comments helped as much as the video. My 96 leaks (badly like you said yours did) at the front where it meets the timing cover. I haven't talked myself into the project yet. I know how messy it will be. (I'm in SoCal, you want to do mine?)
@nathanbishop19992 жыл бұрын
If I was closer I’d come do it! It took me a full day because I didn’t know what I was doing at first but it’s pretty simple if you take your time
@kiraholtzer51763 жыл бұрын
Go Bishop go!
@hiladiorivera475 Жыл бұрын
Does it show u how to put filter gasket back on
@tommyhajimoto69685 ай бұрын
Lucky you I had to pull the whole motor out of my S-10 with an l31 vortec. I replaced the front seal too with a plastic cover, instructions sez to put silicone under the plastic cover to the front seal or it will leak. Came to see if someone did it on KZbin.
@lovellbinns862 жыл бұрын
I saw a video where if you turn the crankshaft tdc it will pop the oil pan off (still have to take the torque converter cover off tho) it made life easier for me I didn't want to take the exhaust off but good work, I have to do mine over as im still seeing oil leak from the pan, must didn't put the gasket on good enough
@Dagrizzb2 жыл бұрын
There are two size oil pan gaskets for the 350. The "thin" one and "thick" one. Depending on the year, the "thick" one will prevent oil leaks from the very bottom of the timing cover that meets the pan. Oreilly and Autozone do not carry them on hand, they must be ordered at the desk.
@lovellbinns862 жыл бұрын
@@Dagrizzb I have the same gasket he has in this video.
@Dagrizzb2 жыл бұрын
@@lovellbinns86 same as in color?
@Dagrizzb2 жыл бұрын
@@lovellbinns86 there are two different thicknesses of gaskets. According to summit racing: The OEM oil pans made between 1955 and 1974 used the "thin seal." The OEM oil pans made in 1975 and later used the "thick seal." Most aftermarket oil pans use the "thick seal." I have replaced my gasket 3 times now. First when I got a crate engine. Second when it leaked. Third when the replacement leaked. Now, for the third instance I had purchased a felpro gasket from Oreillys auto part number 0S34500R. The same blue one as in the video. This gasket is what is commonly stocked at many auto part stores. The other size of gasket I came to find was felpro, part 1886 also available at Oreillys. However, many stores can only order this part by request. The way to tell what gasket you will need is to measure the height of the portion where the timing cover sits at the front of the oil pan. Place a ruler across the top of the front end of the oil pan, measure the height from the bottom of the timing cover area (the curve) to the ruler sitting across the pan. 2 1/4 is the old "thin" gasket OS34500R 2 3/8 is the new "thick" gasket 1886.
@lovellbinns862 жыл бұрын
@@Dagrizzb color and gasket, I got my gasket from auto zone which is more than likely the one u got from O'Reilly. Im about to take this pan off for the 5th time. Im not sure what im doing wrong but I've never had a hard time replacing a gasket like I do for my obs.
@bobburnett59732 ай бұрын
Hey bro. Could this be done on 03 s10 4.3 with 2wdrive?
@genestump9199 Жыл бұрын
Hi, Thanks for the video. What were the torque specifications for the bolts? Thanks
@nathanbishop1999 Жыл бұрын
I couldn't find the torque specs so I just did it fairly tight
@kylyn6082 жыл бұрын
My 1996 is leaking badly at the timing cover meet and I've got everything unbolted but its stuck up at the back end of the pan and wont come off
@dennisdain9872 жыл бұрын
Same here. Mine will not drop down far enough to slide back. I believe the dip stick tube is holding up the process. I just watched this video again and it looks like he removed his dip stick tube. Have you had any luck with yours?
@clintutter77982 жыл бұрын
I did everything you did to the T, even loosened the starter and still the pan wont drop..i noticed you were wiggling the front of the pan twords the fan ?..what was in the way?
@nathanbishop19992 жыл бұрын
You may have missed a bolt, there are some really hard to get to pan bolts. I also used a mallet to hit it loose
@whitewolf40162 жыл бұрын
Thanks
@bamabassgrabber Жыл бұрын
If the oil gasket is broke would it cause everything to be covered in oil on the underside?
@nathanbishop1999 Жыл бұрын
It can, it depends on how severe the leak is and wear it was leaking from. Mine was leaking from the top of the pan were it has a U shape cut out, it leaked pretty good on the underside of the truck
@dennisdain9872 жыл бұрын
I'm starting the process. Is there any kind of gasket in that exhaust section you lowered to remove the inspection plate? I've got the bolts off but quit for the day before I broke it loose.
@nathanbishop19992 жыл бұрын
I did not see any gaskets when taking it apart. Mine separated fairly easy.
@dennisdain9872 жыл бұрын
@@nathanbishop1999, thanks. So no exhaust leak when you put it back together? I plan on attacking things in the morning. I'll keep you posted.
@nathanbishop19992 жыл бұрын
@@dennisdain987 no leaks, it went back together pretty easily
@dennisdain9872 жыл бұрын
@@nathanbishop1999, so it looks like you didn't use any gasket sealer anywhere? I am reading so many different scenarios on these 350 oil pan replacements. Maybe simple is the best way. My problem today was I cannot get the pan out with the space available. I know you said you struggled but I don't feel like i am even close to getting it out. I guess I'll unbolt my motor mounts and jack up the engine. I can't think of any other way.
@nathanbishop19992 жыл бұрын
@@dennisdain987 I didn’t use gasket sealer but I also didn’t do any research. If you want to be safe then use the sealer. I got the pan out fairly easily with enough space. Is your truck 4wd or 2wd. If it’s 4wd then you have more things in your way
@LuisMoreno-rr8jd Жыл бұрын
Se puede quitar tambien en el motor 5.7 lt1 1994??
@ismaelmunoz48022 жыл бұрын
So you don't use gasket sealer ? I did the oil pan gasket on my 96 c1500 and it still leaks from the front seal any advice
@nathanbishop19992 жыл бұрын
I did not use gasket sealer for mine, when I took the old gasket off I made sure the metal surface was really clean. You can add a sealer at the front and back of the block where it meets with the oil pan. It could also be leasing from oil cooler lines or one of the main seals. I’d clean the area up really well and see if you can pinpoint the leak.
@Dagrizzb2 жыл бұрын
There are two sizes of the gasket. A "thick" and "thin" variation. Certai models after a certai year take the "thick" gasket.
@rodneyhaskins77822 жыл бұрын
mine is leaking down the front of gasket after I changed it
@ismaelmunoz48022 жыл бұрын
Here's my up date guys , after I change my oil pan gasket it was still leaking from the front seal I change in a couple Times befor I found out on the vortex 5,7 the timing cover is that plastic which had a hair line Crack that I couldn't see I hope this helps
@davidbro13329 ай бұрын
You think 91 GMC Sierra simular or pain in the neck?
@terrywilliams409 Жыл бұрын
Did you have to remove the engine mount bolts & raise the motor to get the oil pan out ?
@jaydegelder2964 Жыл бұрын
Terry , He didn't.
@nathanbishop1999 Жыл бұрын
This is a 2wd drive truck so it is a little bit easier, I am pretty sure the 4wd have more crap in the way
@papi_rayan95702 жыл бұрын
Man I have a 95 Silverado single cab and just replaced the gasket been taking me days to work on it due to work and it being my first time as soon as I finished and put everything up I started it and it started leaking next to the starter🤦♂️
@nathanbishop19992 жыл бұрын
Damn old trucks 😂. Was it leaking where the oil filter is at? Or leaking from the pan. I’ve notice some leak because of the condition of the pan and you may need gasket sealer on top of the gasket, I was able to just use the gasket but I cleaned the area really well and my pan was in good shape.
@paulforest137313 күн бұрын
Looks a lot like my 94 c1500 pickup 2wrd.
@nathanbishop199912 күн бұрын
@@paulforest1373 they’re pretty simple to work on and last forever
@Fernandro2 жыл бұрын
3:04 how did you get that bolt off with the two coolant lines bolted on the pan
@nathanbishop19992 жыл бұрын
Didn’t get a good shot on that one, I actually took the oil cooler off and let the lines hang. Take the filter off and then it’s two hex heads inside the cooler
@Fernandro2 жыл бұрын
@@nathanbishop1999 thanks got it
@Fernandro2 жыл бұрын
@@nathanbishop1999 I’m sorry what was your torque spec u did?
@nathanbishop19992 жыл бұрын
@@Fernandro 18 ftlbs. That’s what I was told from a manual. Also do not forgot to change the gasket on the oil cooler or it will leak. Don’t ask me how I know lol
@bruhbedrivin2 жыл бұрын
Did you have to jack up the engine?
@nathanbishop19992 жыл бұрын
No I did not have to jack up the engine
@vr4runner Жыл бұрын
Crap, something that seems like it should be simple turns into a full day of taking off exhaust pipes and cutting rusty bolts and getting covered in oil😖 then everyone says”you’re lucky you have a plow truck…” 😂 My name is bishop too, we must be cousins!
@nathanbishop1999 Жыл бұрын
True that, I had no clue what I was getting into, but its worth it in the end for saving the money on labor
@letsdanceoo Жыл бұрын
Tried the KYB Monomax and the Gas Adjusts varieties of their shocks Not happy with either. They are supposed to be it. Bilstein's are coming.
@nathanbishop1999 Жыл бұрын
Almost all of the shocks made now a days are garbage, you usually have to spend a good amount to get quality auto parts in today's world
@StlMar314 Жыл бұрын
2wd or 4wd?
@theobsessedguy3652 Жыл бұрын
2. Look at the wheels man
@duncanmcavoy88663 жыл бұрын
Why would you do this? It's an old leaky girl and yeah there might be a spot on your driveway but it's cheap rust prevention.
@nathanbishop19993 жыл бұрын
It was leaking bad, it needed a quart added every other week and it only gets driven 4 miles a day. It was my grandpas truck and he left it to my dad. So the truck means a lot and I want to keep it running for our family since it is one of the only things we got left. The oil pan gasket was really bad, and I also did it because I love to work on everything myself. Might be a pain to someone else but I love the work
@nathanbishop19993 жыл бұрын
And one more thing, we are in California, no such thing as rust out here haha
@duncanmcavoy88663 жыл бұрын
Ah I getcha. Something about an old chevy getting passed down and still wanting to work is pretty awesome!