Okuma Lathe Parameter setup

[@javiercastillo2470]

I was wondering if you could do a video using m695 I moved the keys on the parameters for this code I added code and I’m still getting no a code saying not reading file I also turned off and turned on machine since I moved parameters please help I’m running a loc650 okuma

[@imranmdyatim3674]

How to copy parameters from LCS15 and save into disket/USB?

[@JeremyRocket]

Is there a parameter to change the foot peddle for tail stock quill return to not move all the away with a quick tap. P200 control .

[@janikartt]

Hi, we have issue. Loking for help. Chuck vibrate when we turn it in c-lock mode. This happend only when make heavy parts. We figure out that the extra weight is making the chuck overshoot it's position and the vibration is the machine trying to correct it. So watched your video and found parameter: Spindle rotation command stabilizing timer. Is this correct parameter to adjust? Any other ideas to solve proplem?

[@pocketcharleywithgosiger]

Oh yeah! Heavy parts can cause problems. Look for the WORK WEIGHT parameter. There are three settings on most machines, four on larger (no chuck, standard , semi standard, and heavy). Try a heavier setting there, and also on your main operating screen under display change, you can run SERVO NAVI which will test the weight on the chuck and adjust the servos accordingly

[@janikartt]

We check this tomorrow. We had made this part few years. This issue just started yesterday. when hevy part is chuck and push c-lock all good, it also start vibrate if i hit chuck slow on rubber hammer.

[@slavikmarinovski2249]

Hi Thanks for the video. on MULTUSB200 I wonder if and how to change Y axis parameter so that when Y is off - the M tool will be in the center of SP1. sort of a way to compensate mechanical problems with Y axis parameter/ endswitch. is this possible?

[@Emiliano_NSA]

*Hello: Could someone tell me where to get the OSP-P300S Control manuals IN SPANISH ?? Thanks* * * * * * * *

[@arturoflores1771]

Ok, dado que vivimos en el mismo pais y estamos buscando casi lo mismo. Estoy trabajando con un control OSP 700 por primera vez en mi vida, y los ciclos fijos son distintos al fanuc, incluso la sintaxis es distinta y tengo algunas preguntas. Can we talk? Gracias

[@Emiliano_NSA]

@@arturoflores1771 Hola Arturo! Si

[@Emiliano_NSA]

@@arturoflores1771 Hola Arturo!! Mis compañeros de Trabajo utilizaban Mazak, y ahora están operando un OKUMA MULTUS B400II con control OSP-P300SA. Pronto tendrán el Conversacional AOT-IGF

[@victorsalasgavia6610]

Hello, I have a problem with my lathe control osp E100l, I changed the ucmb card, restarted the software, and now I have an alarm 4710 alarm D parameter non set 1 can you help me because I do not have backup parameters

[@pocketcharleywithgosiger]

That alarm means that the user parameter spindle max rotation speed parameter has not been set. Set that manually then cycle power

[@2hrsToChooseThis]

Can we rotate the turret with the hand wheel for checking clearances on Okuma LB3000 EXII? Also, I can’t use G74 or G77 with G138 enabled. Is there a way around this?

[@pocketcharleywithgosiger]

Yes on the turret question: go to your parameter page, find the page labeled TURRET/DOOR, then look for the item NC TURRET PULSE HANDLE. Apply a check mark to that parameter, then the index button will unclamp the turret and allow the pulse handle to rotate it. Once you're satisfied, remove the check mark then press the index button again to have the turret locate the logical index position and reclamp itself. Make sure your X is at the positive limit when doing this. As for the G74/G77 question: you cannot engage a lathe cycle with G138 active. If you have the option called Y offset turning, however, you CAN command a Y position even when G138 is not active. This can also allow you to compensate for turning tool above/below centerline

[@2hrsToChooseThis]

@@pocketcharleywithgosiger I appreciate the response! I’m sure we have Y offset turning, just never used it before. I’ll try it out tomorrow. Have a good 4th! Thanks!

[@pocketcharleywithgosiger]

@@2hrsToChooseThis My favorite move for the offset tool is to put the error in the Y offset column, then have my program take the tool to X___ Y0 Z___. If that alarms out, you'll know you dont have the option. Happy 4th to you too!

[@thienvu7891]

Thanks for your video. Finally I saw my question here. My Genos L3000e with osp 300 Cannot run Lap cycle with Y axis. Can you please show me how to use Y axis for Lap cycle. Thank you.

[@dumitrupaul3893]

Hi, i have an Multus B300 and i have some B axis deviation can you help me to calibrate it to be 0?

[@pocketcharleywithgosiger]

kzbin.info/www/bejne/eIiphmeEp9F2jdE this video has a bit of the basics

[@rasto1695]

hey how do you make your machine lb 3000 exII to be always in m42 for more than 840 rpm. ?

[@pocketcharleywithgosiger]

Once you select the range, it will stay there throughout power cycle until an M41 overrides it

[@rasto1695]

​@@pocketcharleywithgosiger yes, but i want prioritize m42 always, i set m42 and machine always rewrite it, im using igf. i want m42 always to be on.

[@Swaruplenka]

optional stop not activated on my m/c.

[@centongbuburx]

how can i download the software?

[@pocketcharleywithgosiger]

@@centongbuburx PCNC Master is only available thru your local Okuma retailer. It is not downloadable from the web

[@derick3482]

HOW do you change way lube setting ?

[@pocketcharleywithgosiger]

It’s is way NOT recommended to do so. Okuma turning centers use a lot of lube, and the engineers set it that way intentionally.