One Ton Swapped Jeep Cherokee Gone Wrong Part 2

[@NagiCheeks]

Thanks for sharing! I bought my daughter a similar XJ done half a$$. Great build, I hope you don't mind I'm gonna steal some of your MODs. 😉

[@adamswaz4878]

Hf icon snap ring plier set is your best bang for your buck and will reach in there no problem I had to get the set for this exact reason

[@Mineboy-10-8]

looks great so far! Love your channel

[@loganschultz3236]

Genuinely enjoyed watching you beat the head of that bolt with the square tubing

[@Grewsum2Sum]

If it's the closest thing around why not

[@Grewsum2Sum]

Also, that was a peice of wood lol not steel sadly

[@gregj.gotham4402]

Looked like more tire out the passenger side fender but you moved the camera to fast for a good look. Got to say you know your 4x4 stuff real good. Like to see it in the sun slower camera movement but to see how you knew what was wrong right off I bet it is done right.

[@Grewsum2Sum]

Sorry we dont have the jeep anymore or else i Would !

[@CodyFazio]

Been here since the idi build, great channel

[@Grewsum2Sum]

Thanks!

[@fjnagle2nd]

In situations like this, I use serrated flange nuts and bolts. You usually don't need a wrench to hold the head (with clean new fasteners) and you can impact them right on.

[@Dripix-uo1nu]

Sup love the vids can you do a video of upgrading your center console bracket from jcr off road

[@Grewsum2Sum]

That will be in the next vid but we got one from dirtbound

[@Dripix-uo1nu]

@@Grewsum2Sum ohh ok if I see that it’s good an solid I’ll get the dirtbound

[@Grewsum2Sum]

@@Dripix-uo1nu it's literally the same thing, super easy to install it looks like

[@Mattyew]

can i bring my XJ to you guys to make it a (white) buffalo?

[@jameslund221]

Now that’s using your head so to speak, holding the camera in your mouth. I even subscribed for that. lol

[@runningproblem]

How the HELL did a one ton axle fit under the rear of this thing without cutting it all apart?

[@Grewsum2Sum]

We put tons in every jeep we have lol never had that issue

[@runningproblem]

@@Grewsum2Sum what shock length do you use? Seems like every one I see cuts the entire back end apart and makes new wheel wells.

[@Grewsum2Sum]

Boostwerks shock towers, cut a section out of the wheelwell stick em in there and weld up closed. Then choose the shock of your liking

[@runningproblem]

Grewsum 2Sum thats about the only other option I could think of. Not many choices to fitting 38” or larger tires in there.

[@Grewsum2Sum]

@@runningproblem i have 40s on my jeep with only 4.5 inches of lift

[@TheBeardedJeeper]

Lookin good guys

[@Grewsum2Sum]

Thanks!

[@rodrigogarcia8453]

Great work!

[@coreysgaming1868]

Where u located? U seem to know ALOT about xjs

[@Grewsum2Sum]

North jersey

[@05glisedan]

Lots of work done to that XJ. Stiffeners next? Looks good..

[@megandalessandro4290]

Da garageeee

[@sriburk]

nice

[@jakerogers4327]

i luaghed my ass off about the control arms.. i actually have the same truss and long arms, and did the truss before hand.. truss is together like the instructions says, but its a absolute pita to put the control arms on. think it has to do with how much bigger the axle is, so distance is off... plus its a tj swap truss not a xj swap truss, which means the upper mounts angle is off by a few degrees

[@jakerogers4327]

but what tcase linkage did you get? and ya like it? i currently dont have any and its sucks to climb under it to change it, lmao

[@Grewsum2Sum]

@@jakerogers4327 boostwerks linkage

[@jakerogers4327]

@@Grewsum2Sum nice, I ended up getting a rip off Amazon one, but seems pretty stout, made outa like 1/4” plate... think I saw ya in the boosted 4.0 page on Facebook not to long ago 🤣 saw you comment and was like wait a second 🤣

[@Grewsum2Sum]

@@jakerogers4327 lol 😆