OnePlus Nord 2 5G Disassembly Teardown Repair Video Review

[@zayevasulf1680]

Thanks you very much for your video. I just replaced my usb-c charging port and i can now charge my phone without holding the usb cable. Cost of the operation : 15€. You're a money saver !

[@PBKreviews]

Glad I could help :)

[@thecommentator6694]

Just ordered myself a new charging port flex cable for the same reason, really helpful video!

[@thecommentator6694]

Just replaced my loose charging port by following this, thank you :)

[@PBKreviews]

You're welcome, and thank you 😀

[@janhorejsek9574]

Thanks to your video, I managed to replace my battery relatively easily.

[@PBKreviews]

Thanks! glad it was helpful.

[@lucamagni99]

Excellent disassembling review! 👌🏻🔝

[@PBKreviews]

Thanks!

[@smaqsmar]

Loved your video, you are dam under-rated

[@Hyouriku]

1:53 - what are these coaxial cables called exactly? The white cable is slightly damaged (isolation) and I needed to isolate it by myself. I think about replacing it in the future but I just can't find the name of them (and where exactly I could buy them). I mean, the closest I found was "mini coax" MHF4 - but I really don't know if that would really be exactly the one used in the phone. Edit: I just recognize that it is not damaged - in your disassembly guide it is not isolated at the same place. Can you explain why it isn't?

[@PBKreviews]

I'm not sure what you mean by its not isolated in place. But its called a Coaxial cable and they aren't easy to find. You can try searching for smartphone coaxial cable. You usually will have to find one from another smartphone that's similar in length to use if you damage your's since they don't usually sell them.

[@Hyouriku]

@@PBKreviews Thank you for your reply - I I meant the rubber sheath. A small part of the cable doesn't have this protection. Can you explain why this is the case?

[@sourajitbiswas1314]

Hello, while assembling, do we have to apply blower or we just have to place the back plate? Please help me with this doubt.

[@PBKreviews]

You would need to apply new adhesive and then apply the back plate (after removing the old adhesive strip). You can watch this video I have on adhesive installation kzbin.info/www/bejne/imXMmoOLfrJqY7s . Also most replacement back plates or battery doors come with the new adhesive pre installed already on it, if not you can check on mobiledefenders.com for original pre cut adhesive if they have it if not you will need to cut down to size your own adhesive strips.

[@sheepdog_81]

Thank you! This made replacing usb-c charging port easy!

[@PBKreviews]

You're welcome

[@shreyanpanja2869]

Watching this on Nord 2 feels awkward and also good 😊

[@chiraggaikwad15]

Same

[@miagi9]

thanks for the amazing video.... where is the "data of the phone" the harddisk placed?

[@chiraggaikwad15]

It's in the motherboard UFS 3.1 chip

[@capofigo]

Is any super glue good for this? Or do you need a special glue?

[@spetauskas]

hi, is it easy to damage mic with sim tray opener, because I mixed those holes and put a sim tray needle in there and pushed.? is it means it is broken ?

[@PBKreviews]

Hi, no you should be fine.

[@sm72691]

Bro i think this is common prblm for nord 2 users. I myself did it + also found anothr comment on this..

[@girguntan]

employee: Boss how many copper should we put into the Nord 2? Boss: yes

[@Jackson-s9g5n]

Could the reason why it has so many cooling components in different areas is to help with the powerful processor or to help when using the 65 watt fast charger?

[@PBKreviews]

To draw heat away both from the processor as well as the battery. A large portion of the vapor chamber is underneath the battery as well as the graphite film the goes over the top of the battery, so I would assume they planned for it to generate a good amount of heat.

[@Jackson-s9g5n]

@@PBKreviews thanks for the info

[@PBKreviews]

@@Jackson-s9g5n you're welcome 👍

[@k7editfactory989]

You just saved the day for me. Thank you so much brother.

[@PBKreviews]

You're welcome :)

[@DaChocapic]

Where is the gps chip located on it ? My gps isn't working anymore after a screen replacement

[@D_Q001]

The magnificent video was very beautiful 😍🤩👍♥️

[@PBKreviews]

Thanks!

[@lingeshwarans4512]

What is the name of that black paper above battery and for what is it used for???

[@PBKreviews]

graphite film, to transfer heat

[@cazaneugen4373]

Hello I have one plus nord 2 5g that is has black screen but touchscreen is working,could be a lose connector or something else? Display is not damaged Thsnks

[@ZishanTherapy]

Sir you have EDL Test Point for this phone? Brom Mode not detecting after pressing Volume Up + Down

[@PBKreviews]

Sorry I don't know where the EDL points are.

[@ZishanTherapy]

@@PBKreviews okay sir

[@Kimmorto]

Did you find the test point?

[@wasu2089]

bro my buss card is cut in nod 2 have i to change the display or any other solution plz reply

[@jippo91]

Hi I just bought nord 2 5g and like an idiot pushed the sim pin into bottom mic port. I heard something crush and now I'm worried that I broke something in there. The crush was the same kind when I found the real sim port ejection hole and managed to get the port open😑 there was no pictures in the manual about the right hole and I'm really pissed for 1+ for not including one. Did I just break the mesh or some protective membrane or do I need to send my new nord 2 to the dealers repair shop?

[@PBKreviews]

Hi, you should be fine. If anything it might have just been the mesh filter. The mic sits above the hole so it would not be damaged.

[@jippo91]

@@PBKreviews It kinda felt like the mesh filter🤔 thank you very much for the answer🙂

[@PBKreviews]

@@jippo91 you're welcome 😀

[@debanjansaha1304]

My nord 2 fell from 6 ft. Though there is no visual damage, there is something loose inside. When I shake my phone, feels like a screw is loose. What do you think may go loose inside

[@PBKreviews]

It might be that metal bracket which covers the flex cable for the LED flash.

[@thatvoiddude6188]

It probably is OIS

[@shrill_kill9929]

Thanks for the knowledge of graphene flim.

[@PBKreviews]

You're welcome :)

[@debodyutikar8209]

I accidentally pushed with sim ejector tool into the secondary mic port right beside the sim tray. Can it damage the mic? I cannot understand watching the video. Help would be appreciated!

[@sm72691]

Same with me. I was even trying with a pen & the pen's nib broke & got stuck inside. Took to a local repair shop, but he said he cudnt find sny nib inside, I face extreme calldrops & call disturbances (noise)..

[@a_Weird_one]

How much does a new screen cost my Phone works but the LCD doesn’t, touch and all buttons work and charging

[@johnnadelgalang7626]

where i can buy lcd for nord 2 or do you sell?

[@PBKreviews]

They have them on ebay or other websites.

[@bert9427]

Do I need to remove all those boards to replace the battery?

[@PBKreviews]

You would need to remove the back plate and the screws on top cover as well as the top plastic cover to gain access to disconnecting the battery cable. At that point you would be able to replace the battery, you wouldn't have to take anything else apart.

[@bert9427]

@@PBKreviews thanks, this would come in handy since no oneplus service centers near me.

[@samirmohanty5561]

ଆମେ କଣ ଖୋଲା ସିଖିନୁ 😂

[@arob9422]

How to replace Power Button for OnePlus Nord 2 5G?

[@shubhambhondve3101]

I need to do that too, somebody please help.

[@andreasringlstetter1719]

As far as I can tell, you will need a new frame, as the button is integrated tightly. If you can't recycle the frame, you will also most likely need a new speaker assembly (top one, not the bottom one), as the glue sticking to the frame is stronger than the glue holding the speaker itself together. Some brute force is also required to pry the vibration motor out. If you have to swap the frame, you will also have to remove the display on the rear side of the frame, and that one is actually tricky as there is a really thing but brittle plastic frame around the display which is prone to breaking even if heated up. Don't try to remove the display until after you have removed the bottom PCB, as the cable is really short and will get stuck on the red rubber piece.

[@urstruelysrikanth1789]

Bro i accidentally poked my sim ejection tool into the microphone hole at the bottom in OnePlus 9R does it cause any damage to the internal parts of my phone please tell me ? And I want to know whether the hole is closed inside on the other end or not please help me

[@PBKreviews]

Hi, you should be fine. The mic and filter are seated above the hole. So they wont be damaged.

[@urstruelysrikanth1789]

@@PBKreviews thanks bro you solved my biggest problem but my doubt is " is I It closed from inside "?when I pushed sim ejection tool there is hard surface what is that???In next teardown video please show how the hole is closed from inside and show tutorial by pushing sim ejector tool from that hole "Many people did the same mistake "

[@MrTamizhil]

It's very professional... Thanks for the video... What do you think about Nord 2 from your point of view... I'm going to buy this mobile is it worth

[@PBKreviews]

Thanks and you're welcome. I think its a pretty solid device. :)

[@goner5991]

What do I do if my phones adhesive seems to have maybe melted off? Because the screen seems to be wanting to fall out? Any solutions

[@PBKreviews]

You would probably need to apply new adhesive. You can use B-7000 glue for the screen and frame.

[@benjoe177]

Hy! I fell down my phone, and the screen stopped a moment, cannot notice any touch and after the phone looks turn off, because i cannot call the phone, cannot work for charging, not vibrate, not turn on, do not do anything. Also not works for USB connection. The service says after checking the screen should be replaced. Is it possible the system(the phone) totally looks dead, when just the screen died? If i disassembly the phone and disconnect the screen connector cable, should it not start the system also? How can i look if it is really the screen died just? Thanks a lot.

[@PBKreviews]

yeah sometimes its like that, when the screen doesn't work, there is no boot or function.

[@SurajThakare0]

My torch (flash) is not working, it works when I press hard besides the camera. I think it's water damage. How much will it cost ?

[@PBKreviews]

You would have to take it apart, clean out any water and make sure the plastic cover inside with the led flash is seated properly to the board to make a contact.

[@SurajThakare0]

@@PBKreviews thanks, I'll probably give it to repair shop

[@rollno7924]

I purchased the phone 3 days ago but I notice today when I shake the phone and take it near the ear it creates some sound like tik tik in the camera section may I know what this sound is of ,and is it common in all one plus Nord 2 devices or is a fault in my device only plzz replyy

[@o-prime]

OIS: optical image stabilization

[@med0374]

My volume down button is faulty, with some minor pressure the volume goes full down, you don't even have to push it 😓. Do you think the whole volume button needs to be replaced or what else can I do? Thanks for your attention, and congratulations for your great video 🤩

[@PBKreviews]

Thanks. You would need to replace the flex cable for the volume keys which has the clickers on them that detect when the button is being pressed.

[@med0374]

@@PBKreviews you won't believe me, I use some alcohol in the button and that solved the problem 🤩 I think some flour was causing this issue since I was cooking some pizza while watching the tutorial in the phone 😅, although thanks for your answer 😃

[@PBKreviews]

@@med0374 you're welcome but be careful when using any sort of liquid on a phone especially when the battery is plugged in, you can cause a short and damage the phone.

[@a2masti724]

Hey my alert slider not moving it sticks what can i do 😢

[@PBKreviews]

Try using a tooth brush to brush around it and see if you can clean it out. If not, you would need to take apart the phone and remove it to clean it or replace it.

[@hcryp132]

First time to saw a lot of cooling pads on a phone

[@PBKreviews]

👍

[@simplifiedmba9340]

Hi thanks for video any idea why Nord 2 blasts

[@PBKreviews]

No problem, what do you mean the nord 2 blasts?

[@kanchansharma8640]

Haw to change vibrator swich

[@heenajamkhandi3173]

What is the price of battery?

[@PBKreviews]

Depends on where you purchase it from, the price can vary from place to place.

[@randomhuman277]

My OnePlus Nord 2 touch stopped working automatically There was no fall damage or water damage i was using the phone and after some time its stopped working, i jve tried restarting and and all but only touch is not, can you please tell me or suggest me what is problem with my phone

[@PBKreviews]

Try doing a software update on the phone. You might need to manually do it with your computer and connect your phone since your touch doesn't work.

[@pritamofficialboy2158]

Sir mujhe tum se bat karni hai mere phone me bhaut problem hai

[@mdrizwanshah1196]

What is the cost of motherboard?

[@PBKreviews]

no clue, all depends on who is selling one and what price they ask for.

[@sagarsingh5474]

Bhaiya mera phone on nhi ho rha koi solution

[@atmosgaming6800]

I am watching my one plus Nord 2😂😂

[@PBKreviews]

Nice :)

[@atmosgaming6800]

@@PBKreviews one plus Nord 2 broking test video bro😁😁

[@d1vyata]

My nord 2 is broken badly....its on but the its been 6 months they didn't repair my phone.... repair combo not available 😶💔

[@PBKreviews]

oh that sucks. Whats broken the screen? There are some screen with frame combos on ebay but they are around $175

[@Maratha93]

Why are nord 2 blasting any design flaws you noticed?

[@PBKreviews]

Hi, I did not understand your question entirely. What do you mean exactly?

[@simplifiedmba9340]

@@PBKreviews in india it's blasting

[@dod-do-or-dont]

Oo. So it actually have some colling for cpu. 😀.

[@sadloveshayri752]

Thanks dear bro

[@PBKreviews]

👍

[@coolashiqtech6282]

Nice

[@PBKreviews]

Thanks!

[@lessthanjay5507]

overhere...here...right here.....

[@PBKreviews]

oh you forgot here. :)

[@souravchowdhury100]

Great view of my phone from inside 👏🔥

[@PBKreviews]

:) glad you enjoyed it

[@souravchowdhury100]

@@PBKreviews Yes😊

[@gerardovleon4221]

Y entonces, por qué explotó?

[@PBKreviews]

Not sure why the one that person had exploded but could be many things. Could have been from a strong fall or have gotten stabbed etc. Until it has been researched we wont know for sure, but it's not always as reported. People can cause damage to the phones sometimes and claim the phone exploded but from taking this phone apart, I did not really see any reason or fault internally that would cause that. I did however notice the phone does tend to heat up at times quite a bit (and cools down just as fast) but that could just be from the large vapor chamber transferring heat efficiently out to the surface of the phone.

[@Rahulvlogg-2]

One plus nord 2 selling this motherboard in price

[@j-tagpro2454]

Charging flex cable take out is edited/fake😂

[@Hyouriku]

I don't know what you mean. it was very similar - if not the same - in my phone.

[@pimpinal004]

Weird phone names

[@PBKreviews]

lol yep.

[@anujayachathuranga2578]

❤❤