Hello! My dear ones, I here in Brazil-Diadema-SP, use isopropyl (isopropanol) with benzine in the 1/1 proportion. I use an injection syringe to apply. And patience with the use of a knife and a small screwdriver, so I make my way. Start by opening at some point and then the product penetrates and detaches from the plastic. Hugs.
@jagonick13 жыл бұрын
What did you spray on first ?? And yours just comes off easy compared to other videos iv seen !!
@pepecapirote74613 жыл бұрын
Hey bud, what is the liquid you are using? I managed to get one lens off prying it out, a little damage but acceptable. I have to do the other and would like to try using the liquid.
@Trodpint-A6 жыл бұрын
No way this is real.
@vandor8600gt2 жыл бұрын
Hi, fluid name? with which you released the glue.
@qq98pp6 жыл бұрын
请问那是什么水?
@headlightsprojectorretrofi51786 жыл бұрын
Hi bro. do you still selling the liquid ?
@jeffreydharter Жыл бұрын
I don't believe he is working with an original lens as I cannot see an access plug above the low beam light.
@ziadalammar37205 жыл бұрын
Hi . If you allow what this article has made the bottle clear easy.
@fear198915 жыл бұрын
simply has no glue left on the channel where it should prevent water come inside the headlight , if you never had opened your headlight , use hot air gun to warm up the glue and you will be able easily to take off the front cover. When you done and you want to put it back use a bit of silicone and a bit of warm up with your hot air gun and job done.
@moutasmmusleh50234 жыл бұрын
Dude I need your help I have a m5 n the lights are good just need to change the cover of the light and the color can u help me ?
@jameswu28374 жыл бұрын
Some people bake it in the oven
@luistorres6022 жыл бұрын
Exactly I have done that myself and it works just fine 👍
@bessiboi777Ай бұрын
@@luistorres602 does it really work. Really need to be able to change the cover on mine without damaging the headlight. Don’t have the money to fix that😢
@user-gl8ow5ob6n6 жыл бұрын
Hello Henry Khoo, I am from Bulgaria. I'm working with headlights, can you tell me what it is you're doing to open headlights?Maybe on personally !!!
@Kalinkamaen6 жыл бұрын
I think he is using Isopropanol. Look at this site at the bottom: www.perma.com/concrete/spec0022.pdf You can see that isopropanol is softening perma seal.
@blackybacsi4 жыл бұрын
Fake! Es ist eine unglaubliche Arbeit. Wenn Du kein Tausendsassa bist, fang nicht an. Weil Du es auch bereust, dass du angefangen hast. Die Klebereste zu entfernen auch ein Wahnsinn. Die alte Kunststoffteile brechen, wie die Grissini. Und dicht zu machen ist auch ein Glückspiel.
@m.l.rbrand4 жыл бұрын
Where can I buy my 3 minutes back cz there is no way in hell this is real stop misleading people man
@giannerissantiago60513 жыл бұрын
What other liquid can I use?
@travelnaturephotodji Жыл бұрын
What whater you use?
@BK_Rocket16 жыл бұрын
fake..after opening there are no leftovers from original silicon glue either on the housing or on the headlight glass...what happened to it? dissapeared?
@TheKarabala6 жыл бұрын
Dalibor 1978 tako je
@stevebloodstevesplace46393 жыл бұрын
guy is gull of shit the fem has no voice
@keesengtan1098 Жыл бұрын
老闆這是什麼藥水?去那裡買。
@A-HotSauce2 жыл бұрын
I am pretty sure after 15yrs mime will come apart same all seals are toast from uv light throw the isopropanyl on good to go
@sharifgabriel83462 жыл бұрын
de blackfiting in the glas for the light can you untie it
@senghian14 жыл бұрын
BRO, where can buy the water ,i am in malaysia
@elvinsyee6424 жыл бұрын
Halo boss. I am from Malaysia to. They uce thinner or rubbing alcohol
@adamfirdaus4242 жыл бұрын
@@elvinsyee642 iya meh???
@ANVAL125 Жыл бұрын
I used laquer thinner on a siringe and worked my way around wetting...after 3 to 5 minutes I started to ply out using two to four flat screwdrivers just to keep the preassure and rewetting with the siringe. Tape your lens or avoid laquer thinner to wet lens. It came out in less Than 20 minutes. Even old tar or glue get soft and workable.
@xtatic32946 жыл бұрын
HEY smear some maynonaise all over the sides and it opens up lol j/k ...dorks
@solarcircle35086 жыл бұрын
ага))) прям так и снял заводской герметик))) чтоб снять заводской герметик фару надо в коробку положить и направить фен минут на 20 и только после сильного прогрева он начинает отходить и то возможно 2-3 раза греть придется, а это у тебя сопли держали стекло)))
@stoldrewdomy7 жыл бұрын
What kind of fluid is this? What do you use? I need it! :) I have the same job to do with the headlight....
@JTWu-vs2fm6 жыл бұрын
It's mineral spirits
@kinginanorth4 жыл бұрын
Holy water
@mehmett1195 жыл бұрын
🤔🤔🤔😱😱😱
@Ali-uv3dz Жыл бұрын
No way
@rolo95706 жыл бұрын
200% Fake
@dockbuilderguy25914 ай бұрын
Is that the new spray i think its called tihsllub spelt backwords. Let me know ill go get it thanks
@ungkiwiranugraha32396 жыл бұрын
what kind of water dude? it is alcohol?
@kinginanorth4 жыл бұрын
It's called Fakohol
@harshMaru-hb1em10 ай бұрын
Please spray name plese
@netuno967 жыл бұрын
they are permaseal ? you use acoohol ?
@henrykhoo39737 жыл бұрын
Renan we don't use alcohol. Is a formulated liquid for our company to open auto light for restoration.
@netuno967 жыл бұрын
Henry Khoo nice, have the name ? i want ro open permaseal headlight, but is hard, heated and no open
@henrykhoo39737 жыл бұрын
Renan not sure if my company sell this. will check it and up date you.
@netuno967 жыл бұрын
Henry Khoo ok, i live in Brazil, if you can tell one similar liquid ! i need this so much
@markklopman14377 жыл бұрын
dude... its fake...
@yavkata133 жыл бұрын
Dude can you tell me name on the water.How you open this headlight.I have headlight on my bmw e39 and not opening😥😥😥😥
@pepecapirote74613 жыл бұрын
Stick your e39 lights in the oven, it softens the glue to release them easily. They changed the adhesive on the e60
@lukasstiftner11672 жыл бұрын
I did it today the 3th time.. I Bake the Headlight 15min at 220 degree. Than work with 2 screwdriver, it goes off really easy like in the video!
@kingly79462 жыл бұрын
Ok, did you preheat to 220 first before putting it in?
@lukasstiftner11672 жыл бұрын
@@kingly7946 no preheat.. Put in and than put the gun in.
@kingly79462 жыл бұрын
@@lukasstiftner1167 ohhhh, ok...you mean 220 with a heat gun and not oven?
@lukasstiftner11672 жыл бұрын
@@kingly7946 yes
@bessiboi777Ай бұрын
@@kingly7946 bro were you able to do it? In real trouble and need to fix it myself😢
@user-nf2xp7xj3v6 жыл бұрын
อะไร..งง
@jjcoding26574 жыл бұрын
So ein Blödsinn, wieso macht man dann so ein Video? Man sieht doch schon, dass du das Cover hinten zerstört hast und das war vorher
@DAVESPORTCARS6 жыл бұрын
Fake
@geraldhumber68492 жыл бұрын
BS
@ariffaizad29716 жыл бұрын
bagi no please
@mee_mumin Жыл бұрын
hehe, it's not poshible with oryginal never opened headlight 😄