Replace and repair leaking seals on Mercury 60hp 2 stroke lower unit gear lube leak , I used SEI parts and can get whole bottom kit on ebay ,on my Bass Tracker bass boat restore @Vassmotorsports
Пікірлер: 51
@rogerbranham50834 ай бұрын
Great Video, you do a very good job showing and explaining everything you're doing
@Vassmotorsports4 ай бұрын
Thank you so much for that, im glad if my videos can help someone out sometime, thanks for watching Vassmotorsports and hope ya check out some of my other videos, always something different, not just boats although they are probably my favorite haha
@pocketjokers1 Жыл бұрын
Very detailed video on this procedure, should use Silicone grease instead of Vasoline on anything rubber or plastic petroleum based grease like Vasoline can be damaging to some rubbers and plastics.
@Vassmotorsports Жыл бұрын
Thank you and Thanks for watching Vassmotorsports, its an oil seal anyways but ive been using vasoline for many years no issues, but ive also used wheel bearing grease to hold seals in place when in a groove and ive used silicone, sometimes i just run with what i have handy at that time lol , ive used motor oil even wd40 haha , luckily not many issues over 30 + yrs , not to say cant get an occasional cheap bad China seal or gasket tho
@Turtle1402234 ай бұрын
Hey thanks for the video! I have the exact motor in your video. When the motor is running it pumps the water just fine through the pee hole and through the prop. But I noticed that it is also leaking water on the backside lower shaft case. Small hole right in the middle of the lower mounting bracket. Is this normal?
@Vassmotorsports4 ай бұрын
Thank you and Thanks for watching Vassmotorsports, hope you check out some of my other videos, unfortunately I sold that boat right after i did the full restoration before this video so i cant say for sure ,but I just had a little Sea Nymph boat i sold last week with a 90 hp johnson outboard and it did very similar to what you are explaining because i wasn't expecting it to be shooting water out of that area either ,, so if it is an actual factory hole on the leg than i would expect its normal
@paulmayhan86735 ай бұрын
Thanks for the tutorial, but you completely skipped changing the shift shaft seal. I’m trying to figure out how to get it out and what it needs. Can you help?
@Vassmotorsports5 ай бұрын
Thanks for that. It was so easy I didn't bother showing. Used a pick or small screwdriver to pop old seal out (pay attention to the direction of seal) and used a deep socket to push new one in. Very simple. Thanks for watching Vassmotorsports and hope ya check out some of my other videos
@lrob2088 Жыл бұрын
Really good video, keep up the good work
@Vassmotorsports Жыл бұрын
Thanks so much, and thank you for watching and subscribing
@dianavassallo6852 Жыл бұрын
very impressing work dude keep up the good work
@Vassmotorsports Жыл бұрын
Thanks, always more videos to come
@나-w3e1m Жыл бұрын
멋지네요, 저도 트랙커 보트에요 Very nice video
@Vassmotorsports Жыл бұрын
Thanks for watching
@spiffykitten8066 Жыл бұрын
Great video!!
@Vassmotorsports Жыл бұрын
Thank you for watching
@spiffykitten8066 Жыл бұрын
@@Vassmotorsports you’re welcome!!
@tbarto100 Жыл бұрын
Why do you think the seals were bad even with low hours? Can weather cause it?
@Vassmotorsports Жыл бұрын
Definitely just from sitting so many years and then I got boat running and took to lake( earlier videos) before I ever started spending time and money on restore till I knew was running good , then it sat through the winter again
@tcburgess29397 ай бұрын
I’ve got the same outboard ..ordered a kit from sei..it came with a few extra o rings and seals..I’m assuming these are for the prop shaft?
@Vassmotorsports7 ай бұрын
I would assume it has the 2 wide seals for the prop shaft ,yes , and couple orings might be different because they make the kit so universal for different size engines , thanks for watching Vassmotorsports
@MARKLOCKWOOD2012 Жыл бұрын
here’s an engine gremlin our evinrude e-tec since new has a over heating issue anything over 3,000 rpms on a 150 hp h.o. the heat alarm sounds in the boat. we have a RANGER Z 118 it doesn’t always do it. but if you try n play not every run it will say hot. not the water pump??
@Vassmotorsports Жыл бұрын
Thanks for watching but im not much help on these outboards, this is my first bass boat. All my other boats and boats i restore have mercruiser v8 chevy engines so i know those inside and out
@hotchihuahua1546 Жыл бұрын
Good tutorial ! I will need to put it on my saved videos just in case ! Lol
@Vassmotorsports Жыл бұрын
Thanks and i answered to your other reply about lube change. Thanks again for watching Vassmotorsports, hope ya check out some of my other videos
@dabneyoffermein5954 ай бұрын
He did a masterclass on how you do this.
@chriss8206 Жыл бұрын
Man I've always wanted the 60 horsepower .I use my boat primarily for electric reservoirs .the 2001 motor 40 horsepower Mercury 2 stroke that I have on there only has about 5 or 6 hours total because I'm primarily running electri. when I purchased the 2001 175 special edition it was like a $$2000 upgrade from the 25 which came with the boat to the 40 and maybe another 500 bucks would have got me the 60 .Sure wish I had the money at the time to go with the 60.40 gets around but 60 would be much nicer.
@Vassmotorsports Жыл бұрын
Man that's low hours on a motor. Curious how much was a boat like these new back 01-02 range ?
@chriss8206 Жыл бұрын
@@Vassmotorsports With the motor upgrade I paid 11000 maybe 11100. If I remember correctly the motor from a 25 horsepower to the 40 horsepower upgrade was $1999. I'm actually getting the boat ready to gofor the 1st time this year and the 1st time in 3 years Looks like a new fuel line I'm gonna clean out the carburetor put some ethanol free gas in it and pretty sure she'll fire right up
@levesquem27 Жыл бұрын
I have oil leaking out water intake.... Is this the seal I need to replace?
@Vassmotorsports Жыл бұрын
Yes this is the most common spot ,especially because if it sits alot the oil is not touching it and when in use the shaft is always spinning fast, thanks for watching Vassmotorsports and hope you check out some of my other videos
@jjjrbrown8177 Жыл бұрын
nice work man
@Vassmotorsports Жыл бұрын
Thanks for watching
@marks60729 ай бұрын
my 2021 Tracker Classic Mercury 50 EFI leaks water with the muffs on when flushing.. It leaks where the lower unit and main housing meet.. Is that normal ??. Getting good pee stream out back.. The leak appears to be coming from the water pump housing.. Is a small water pump leak a problem???
@Vassmotorsports9 ай бұрын
Thanks for watching Vassmotorsports but I'm not really familiar with that newer engine. Maybe someone else has a video of that motor or even different HP but closer same year to see , sorry I couldn't help ya ,
@donniegray22884 ай бұрын
What size prop are you running I’ve got the same motor on a 16ft monark a lot like a bass tracker and idk what pitch to run it’s got a 13 pitch now but I think I could go with a taller pitch just curious what yours is
@Vassmotorsports4 ай бұрын
sorry im not sure and sold the boat right after i restored it and did these seals. ,thanks for watching Vassmotorsports and hope ya check out some of my other videos, have you seen the restoration of this boat ? kzbin.info/www/bejne/nqqkc4GhYqilfposi=8UtDAnzLz91T3G_v
@donniegray22884 ай бұрын
@@Vassmotorsports yeah you did a great job I’m currently working on mine myself
@Vassmotorsports4 ай бұрын
@@donniegray2288 thank you so much. and good luck with your project
@donniegray22884 ай бұрын
@@Vassmotorsports Thank you buddy
@rhcoopercatАй бұрын
Why can I not find a single video on how to replace the lower unit seals in a 1991 Mercury 115 hp 2 stroke
@VassmotorsportsАй бұрын
i dont know but should be very similar to this 60hp. have you tried looking for a 120 hp or little bigger if this isnt the same maybe one of those will be. thanks for watching Vassmotorsports and hope ya check out some of my other videos sometime
@rhcoopercatАй бұрын
@@Vassmotorsports I have watched several of your videos .. very clear and concise step by step info ! yours are the closest I have been able to find honestly.
@rhcoopercatАй бұрын
I have looked at larger HP Mercury but nothing that resembles the tower of power 115 Please let me know if you are planning to do a lower seal replacement video.. as I am stumped at this point lol 🙂
@VassmotorsportsАй бұрын
@@rhcoopercat wow thank you for that. and hope it helps ya to get yours knocked out and good luck with your project, I didn't bother with the prop shaft seal as it wasnt leaking and stays in the fluid as its at the bottom
@kcfirearms Жыл бұрын
You did all that work and didn't change the impeller? Why in the world wouldn't you just go ahead and put a fresh one in while you were that deap in?
@Vassmotorsports Жыл бұрын
I thought about it but there is nothing wrong with it and im scared to put some new China junk that will be lucky to make it a year , I pulled it apart last year when i first got the boat and got her running and when i seen how nice this one was i left it then too and sent the cheap new one back , I ran the boat on lake couple times and when i pulled apart this time its still in perfect shape, trust me it bothers me too but sometimes if it aint broke dont fix it