Outlander XMR Axle Replace CV Joint done Can Am

[@patrickfoley6519]

Thanks for the video! I gotta tackle an axle replacement on our Defender HD10

[@RobFarrowATV]

Thanks Patrick! Glad you liked the video. Good luck with your repairs.

[@inkedupred2186]

Very simple vid 👍🏽 Looks like a piece of cake all u need is the right tools! Thanks man!!

[@RobFarrowATV]

Thanks, hope it helped!

[@G-Man-kc2nm]

Well done....easy to follow...thanks for the video....

[@RobFarrowATV]

Thanks Man! Glad you liked it! Thanks for watching!

[@NorbertoHW]

The video helpful whenever if I break any axles on my outlander 🔥🔥

[@RobFarrowATV]

Glad you found the video helpful, thanks!

[@anthonytaylor6053]

good video thanks ima go start on mine 🤟

[@RobFarrowATV]

Thanks, good luck with your machine!

[@CF625TR]

Thanks man! I was driving with 0.5inch gap realised after your video. What would have been if I kept going like that?

[@RobFarrowATV]

Good thing you realized it, would've probably sheared the end of the axle off. Thanks Man!

[@robertwilkey8178]

I was watching you install the new axel and I was wondering if you could tell me how you lined the axel up inside the diff before you drove her down flush with the diff housing?

[@RobFarrowATV]

Slide it in slowly and turn it slowly as you slide it, then when you feel it grab the splines and slide a bit more, you should be good to give it the last push. Good luck!

[@MrNewff]

I have to do the tie rod and cv axle on mine. Do you think I could get the nuts/bolts off for this job without an impact? I have a breaker bar so hoping that will be good enough and not have to go buy an impact.

[@RobFarrowATV]

You should be able to loosen them with just a socket and wrench. I use the impact cause it's easier and faster. Good Luck!

[@pedrogonzalezm.2609]

clean work

[@RobFarrowATV]

Thanks Pedro!

[@superbee6270]

Great video. thank you.

[@RobFarrowATV]

Glad you liked the video Gilles, thanks!

[@Streetglidescotty70]

thanks for the video. I think I have an axle starting to go on my 14 800r XT. this will help save me some $$$

[@RobFarrowATV]

Awesome that the vid helped you, good luck with the axle replacement! Thanks for watching Scott!

[@MainvilleATV]

Good job bud!

[@RobFarrowATV]

Thanks Man! Starting to get to the point where I can do it in my sleep! LOL! Thanks for watching!

[@MainvilleATV]

@@RobFarrowATV watch crappy tire for dewalt impact sales. Got a few real cheap and they're great.

[@RobFarrowATV]

Yep, I get the flyer every week...still waiting for the truckload of money giveaway so I can afford everything I want! LOL!

[@dandaktor6260]

Did yours come with a new diff seal??? Mine just arrived today, no seal..

[@RobFarrowATV]

No, had to buy seals seperately.

[@paulbrowne2324]

Always love do it yourself videos !

[@RobFarrowATV]

Glad you like the DIY vids, some more to come! LOL! Thanks for watching Paul!

[@maff3]

I need to replace my front cv, when I look at it front on is that the left or right? Or is it when you stand behind? I thought both cv would b the same but ebay is asking for left or right.

[@RobFarrowATV]

When You sit on the machine looking forward. Right and left are different sizes.

[@nombr]

Good video, mine was binding a bit when turning. Sometime during my last ride the axle popped off the hub side, I am thinking my knuckle just busted?

[@RobFarrowATV]

Sounds like it! Something always seems to happen on a ride! LOL! Hope you get her fixed up soon Gavin!

[@wreckitruss]

Any tips on a rear axle? going to be doing one soon.

[@RobFarrowATV]

Not really, just make sure you pull it straight out and put it straight in and that it's all the way in. Good luck!

[@larrymcpherson3875]

2010 CanAm Outlander 500 Max, can’t get the front left shaft out, it won’t pop out like yours, kind of like it’s attached or something. Is there a special way to do this.

[@RobFarrowATV]

I am assuming your trying to get the left front "axle" out? Might need some coaxing. There's videos that show how to wrap a strap around the axle and then swing a large hammer outward to pop the axle out...that should do the trick, there's just a clip holding the axle in place but sometimes if they don't have any grease they seize up a bit. Good luck!

[@usbeckoffroad746]

Great video

[@RobFarrowATV]

Thanks Man, glad you enjoyed the vid! Thanks for tuning in!

[@brentjorgensen5632]

where did you get the axle in one piece for 300? Brent

[@RobFarrowATV]

Straight from BRP although I'm sure prices have gone up now...

[@bert26a]

What kind of oil are you using in the diffs?

[@RobFarrowATV]

Was running Royal Purple in the diffs now...

[@bradenpompu9702]

Did you need to re add diff oil? Or was what ran out negligible?

[@RobFarrowATV]

I would check the level again thru the fill screw

[@mrtundranutz1]

Good vid . Low Pressure=headache . Me , low pressure=wicked sinus+headaches and no one believes it .

[@RobFarrowATV]

Ya, same with me and ya, no one believes us! Thanks for checking the vid out!

[@dhrcrew2493]

Suffer from the same. Thanks for this video Rob. Broke my right rear axle last week doing it this weekend.

[@RobFarrowATV]

Good luck with the axle repair and thanks for tuning in!

[@dustinperrydore7713]

Is it normal for the diff fluid to run out when you remove the axle?

[@RobFarrowATV]

Yep. If you're removing the axle you should drain the diff first unless you want a mess. LOL! Make sure the diff fluid is clean and mot milky or brown. If it is then you have a seal leaking. If it's clean then you're good. I usually change the fluid once a year regardless.

[@jaquancraig5335]

I have a 2013 Polaris sportsman 500 ho iv been through 2 axles both broke back to back can anyone help?

[@RobFarrowATV]

Sorry, I don't know Polaris...it all depends on the type of riding you do whether you should try aftermarket axles. Good luck with your issue!

[@bradenpompu9702]

And where do you find the torque specs for putting everything back together?

[@RobFarrowATV]

It's in the manual or you can find it on the internet

[@daviddavilalomeli7344]

Good job but why don't change the wheel bearing?

[@RobFarrowATV]

Nothing wrong with the wheel bearing...I grease them everytime it's apart, still tight! Thanks for checking the vid out David!

[@toddmerriott6901]

Thanks!

[@RobFarrowATV]

Thanks for watching Todd!

[@nostuckmarc8682]

This will make it a lot easier if I have to do mine. thanks for making a video. Did you happen to grease that hub bearing just to see how many more pumps at took from the original time you greased it?

[@RobFarrowATV]

Thanks Marc! Ya, took 5 more pumps this time! Will do them all again soon! Thanks for tuning in!

[@trevorsozio5201]

Where do you get parts for your atv, I have a 2017 outlander 850 xmr and can never find any parts for it, I need a right rear axle, mine is the same way as yours

[@RobFarrowATV]

I get my stock parts straight off the BRP online Web Site in Quebec...unless my local dealer has them in Stock. Everything else I shop around and ask questions on Can Am facebook sites. My dealer had the axle in Stock. ..I like the stock axles, they are very strong! Thanks for watching! Good luck with your repairs!

[@stephenleblanc322]

15mm for this & a 1 1/16 “ for that.” You sure about that?

[@RobFarrowATV]

Works for me...

[@toddmerriott6901]

Headaches are the worst.

[@RobFarrowATV]

Yes they are...getting tired of them!

[@izom]

dont get me wrong- idlove too look your videos and some other guys- all blastin on those powerf. canams- but - to see so much brake - is confusin me...i drive since 6000kms on my slow fat cat- just had to change 2 rubbberboots and the waterpump is wet- not leakin...starts up and runs fine- slow - but fine....;- () hope u can sort all the sh.t out ;-)

[@RobFarrowATV]

Harder you ride it, the more breaks unfortunately! But on a good note, everything is new! LOL! Happy Trails Izom!

[@jH-zu9ky]

Mentioning that this is a front axle in the title would have been very helpful. 😡

[@RobFarrowATV]

You couldn't tell it was a front left axle in the thumb?

[@jH-zu9ky]

@@RobFarrowATV actually, no. When sifting through dozens and dozens of videos on my phone where a thumbnail is about 1" by 1/2".