P0101 Very Important and cheap repair, 2013-2016 Nissan Altima

[@BassMan77]

Thank you Soo much!!! Fixed my P0101 issue on my 2013 Nissan Juke.

[@DallasAutoDiag]

What did you replace or do to fix it?

[@BassMan77]

@@DallasAutoDiag I replaced it with a new black one from Nissan. It was super easy considering I really don’t have experience fixing a car.

[@DallasAutoDiag]

@@BassMan77 awesome 👌

[@jimmygonzales7160]

@@BassMan77 what was it doing before you replaced it

[@BassMan77]

@@jimmygonzales7160 it was idling rough every so often. Also it was giving me a error code P0101. My miles per gallon was also affected negatively. After replacing PCV that issue was resolved. I didn’t realize how much power I lost until after I replace that part. My car is now running like new!

[@jamesmurray9806]

Excellent video! The information the dealer doesn't share. Thanks so much!

[@RedTekno]

Nice! I was about to change the PCV after not finding anything wrong and troubleshooting everything. There are a few things left if the PCV doesn't fix it. The dealership couldn't fix the issue, charged the customer for a new MAF (customer just had a new autozone MAF) and the update and returned the car in the same conditions while telling him they could fix it by installing a cold air system for like 1k 🤦. Good that I found your vid. I needed reassurance 😁. 🙏

[@smvideonow]

That was very systematic. Your are a true professional. Always test. Never guess. Thank you sir

[@DallasAutoDiag]

Thanks for your comment.

[@joeybruington]

I appreciate the thorough explanation of this. Thank you for your time!

[@DallasAutoDiag]

You are welcome

[@johnpage6051]

Nice Video!! Yes, hope their CVT is ok, cause they are crap. My 2014 went out right before my warranty went out, thankfully. Thank you again!

[@DallasAutoDiag]

Awesome. Glad that it helped

[@minombreeslos]

Excellent video thank you, I have watched 20+ videos to solve this problem and yours has been the most helpful. I have a 2014 Nissan Sentra and the service bulletin for the same issue is ntb16-027a.

[@DallasAutoDiag]

Glad it helped

[@federicovega2292]

What did you do to fix it? Thanks

[@8power0]

IT'S ALWAYS GO TO CHECK SERVICE INFORMATION ,, THANKS FOR YOUR TIME !!!!!!!!!

[@FenderStrat19711]

Thank you for this SUPER HELPFUL video! My MIL light came on today, despite that fact that I have had no drivability issues with my car at all. When I checked it via the OBD2 codes, the P0101 code came up. That led me to your video which was SO helpful. I'll have my Nissan guys do the repair, but I won't be freaking out over it..... :)

[@DallasAutoDiag]

good luck and I hope you fix it the easiest and cheapest way.

[@embroideristalavista6485]

Very useful to me as I try to address this problem with my car (2014). This has been giving me trouble for three years and the first I heard that it might be a PVC valve is when I bought a replacement Mass Air Flow Sensor for $181 and the manufacturer (Duralast) included a bulletin in the box! I haven't taken it out of the package yet and am going to take a look at the voltage readings first. The PVC valve is a much cheaper fix than a new sensor. The dealership told me the "fix" was a new wiring harness - for $2,600. I'll try this first. Good video. Many thanks!

[@jamesleyfortune6851]

Hey I just wanted to ask was it your pvc? I got a 2017 versa and that code just came up.

[@shirecain2129]

As an amazing mechanic that specializes in electrical I would like to say great job sir. You are 100% a fellow amazing mechanic. Two thumbs up for this video 👍🏻👍🏻

[@DallasAutoDiag]

Thank you Sir.

[@washingtonpesantez6311]

Thank you for posting this video I had fix my problem with out going to the dealer the dealer estimate was 900 I had follow you steps and bought the pcv valve and light engine is not at my dash board any more thanks

[@DallasAutoDiag]

Glad that it worked for you.

[@tonygaytan9848]

Great video, lot’s of good information thank you.

[@DallasAutoDiag]

Glad you enjoyed it!

[@koreancook]

Had the same problem, intermittent p0101. Coincidently replaced pcv valve and had to remove all coil plugs except 1, used idle air volume relearn, kill engine-> plug in #2 -> idle air relearn -> kill engine and repeat till all coils are plugged in.

[@DallasAutoDiag]

Thanks for sharing

[@ahmedalatrachi2897]

thank you man you did a great job

[@DallasAutoDiag]

Not a problem

[@katana1960]

I think he is right about the PCV being a 23mm. I had a too small 22mm and a too big 24mm, so I tried my standard sockets and a 15/16th worked.

[@DallasAutoDiag]

Thanks for sharing Phil

[@jamessykes9597]

Great Video

[@DallasAutoDiag]

thanks

[@rlt7409]

2013 same code will let you know how it works out. Thanks a lot for sharing very well done.

[@DallasAutoDiag]

Updating tge pcm is really important in this case also.

[@coachtrollinger]

How do you update the pcm?

[@rlt7409]

@@coachtrollinger I wound up selling as is so i didn't do the job

[@samuelschrader6568]

Very nice explanation. Thank you.

[@DallasAutoDiag]

Thanks

[@ahmedalfarsi2]

Thank you very much guy. You really help me.This problem makes the car weak. Sometimes there is no power at all. I left my car with un electrician for one month to fix this problem and he couldn't. Now the car is Ok 11810-EA200 this is part number of replacement black

[@advancedleveldiagnostics]

The TSB says that it only applies if there is no drivability problems, so if you feel no power that's most likely caused by something else.

[@ahmedalfarsi2]

@@advancedleveldiagnostics Yes the problem still there. But not like before

[@javieralcala9805]

r arreglarlo y tengo que Hello, I have the same problem in my car, it is a 2013 Nissan Altima. They charge me 450 dollars to fix it and I have to fix it because it doesn't pass the smog check. They have to reprogram the computer.

[@peter555peter1]

Thank you, Sir!

[@DallasAutoDiag]

You are welcome!

[@reyes3972]

Excelente trabajo.. ya me suscribí

[@DallasAutoDiag]

thanks

[@alexanderking3971]

Been trying everything to get rid of this code on my 2011 2.5 MT and you're the only one who has suggested the pcv valve. I'm going to dealer tomorrow and ordering a new one.

[@DallasAutoDiag]

If not, there is a big chance your pcm needs update.

[@justanothermobilemechanic7997]

That’s a customer for you. I’ve been a mechanic for 21 years. You fix the one issue but they have another that’s not to do with it. And they act like your to blame for that or you did not fix it. Thats why I go on drives with the customer and list off all issues I have and they say ok. So at the end they know

[@DallasAutoDiag]

First thing I do when I get a key of a car to repair is to do a Pre-scan.

[@benjaminlevi7792]

Good job but for transmission need to programing with OEM diagnostic software thank you for your great video

[@DallasAutoDiag]

Unfortunately the owner just replaced the engine before he found out that the trans has this issue in it.

[@DzevatS]

Thank you. This was helpful

[@DallasAutoDiag]

Glad it was helpful!

[@berto8232]

I bought my 2013 Altima new and have put close to 170K miles. Just recently did the P0101 code appear. I changed the MAF Sensor and that fixed the issue for like a month. Now I have the check engine light on again. I did see on another channel that they also replaced the PVC valve when they changed the MAF sensor. I didn’t do that. I think I have the orange PVC Valve. Now I just hope I don’t have to reprogram the computer, but since it’s a 2013, I’m probably screwed. 🙂

[@DallasAutoDiag]

Hope you don't have to. If you do need someone to program the computer let me know at that time.

[@berto8232]

@@DallasAutoDiag Is the reprogramming something a DIY-ER can do or it must be take to a dealer?

[@DallasAutoDiag]

@Roberto Reyes not a diy. Dealer or a tech at a shop or mobile like me who has a dealer software and device.

[@aymenmohamed1134]

nice job

[@DallasAutoDiag]

Thanks!

[@DaOnlyOne]

That was very helpful, just ordered the part to fix mine. I had the same transmission code, I replace the whole transmission or could of just changed the transmission value body.

[@DallasAutoDiag]

Good luck. Hope you won't have to reflash your module.

[@DaOnlyOne]

Hopefully I don't have to, but it can't be helped if it has to come to that. Which I'm okay with that

[@MnyrlindseyTV]

I replaced my transmission 6/23 and kept getting a p0441/ or p0467 code since I first wanted to bring my car in 2022 still getting the code lol changed most stuff to OEM now ima check my wires

[@fatihgumus6753]

When electrical issue happened with MAF, it throws another code than P0101. P0101 means, MAP and MAF readings are irrelevant relative to eachother so better to check for air leakage first ;)

[@DallasAutoDiag]

Thanks for the clarification

[@chestnutwarrior6322]

Thank you for the video ! I have a Nissan 2013 altima with the code P0101 and the car is jerking when accelerating when it reaches 20mph

[@advancedleveldiagnostics]

TSB says it only applies if there is no drivability problems..

[@elprofee2937]

It sounds like the CVT is slipping and will need a cvt if chain is damaged

[@rlt7409]

New subscriber

[@DallasAutoDiag]

Thanks

[@gopes23]

2014 altima with P0101 code. I had the dealer replace the pcv valve and do the re-tune, tsb NTB16-030a

[@DallasAutoDiag]

Code still there or gone?

[@christianmaldonado9068]

How did that work for you?

[@DallasAutoDiag]

@@christianmaldonado9068 after pcm update worked fine.

[@purpledame]

I’ve been so frustrated with my car and the Nissan Dealer 😤 my altima has been giving me issues with this P0101 code for like 3 years. I have tried cleaning the MAF, replacing it, had my throttle body replaced by the dealer and I even replaced the pvc valve and had the dealer “reprogram” my car after installing the new sensor. You guessed it still get this code after all this! My altima struggles to accelerate and need to ease my way into the freeways. I feel like the dealer isn’t fixing the “main” problem to keep siphoning money from me. This code and problems comes up when my car struggles to accelerate and going uphill.

[@DallasAutoDiag]

I would not trust the dealer a 100%

[@DallasAutoDiag]

Find somebody with good skills and equipment To check it

[@pvcarmon1]

Ok had same issue changed a bunch of sensors spent ton of money. Turned out the dam car needed a software update. Dealer wanted crazy money found a Nissan mechanic that did it for $175

[@DallasAutoDiag]

@@pvcarmon1 how much dealer asked?

[@canteskuyapete1459]

@@pvcarmon1 a Nissan mechanic only charged you $175 for it? My Nissan dealer closest to me, charges an arm and a leg, easily any service done by then is $300 service with a smile 😑 smh .

[@chrissatterfield7513]

I’m having the same code on my Sentra but the vehicle turns on and immediately off. If I give it gas. While cranking, it’ll stay on, no problems. But the next morning. Same issue. I’ve cleaned and replaced the maf, problem follows. Next is to change the pcv I guess since it’s orange

[@DallasAutoDiag]

good luck

[@rickymejia8581]

Just checked mine. My PCV Vaulve is Purple but has some orange on the tip. I Felt some air coming thru the side its not suppose to be so as i blew thru it. After installing the new one, is that all u have to do?

[@DallasAutoDiag]

After changing it you need to reprogram your pcm.

[@jakekay5588]

Very very good information! I’m going to check mine as I’ve had a sporadic code for years. If the pcv valve is bad do I have to reprogram the computer too or just change the valve? Thank you so much! 🙏🏻

[@DallasAutoDiag]

I'm glad I could help

[@christopherpatterson8833]

What's going on I'm in dallas I have a lexus gs 450h I need looked at abs

[@quele6990]

I just fix this issue some it could also need a throttle body cleaning it is also in the tsb

[@DallasAutoDiag]

Good to know man thanks for the update

[@Tonyv5378]

Just thought i would leave this here that it may help someone. I was told to clean the throttle body that had black sludge on back inside of it. After months of trying to find cause engine light is finally gone.

[@DallasAutoDiag]

Thanks for sharing. This is definitely one of the regular causes of the code.

[@freddyfudd253]

Did you have to remove the throttle body to clean it, or just spray it out?

[@DallasAutoDiag]

@@freddyfudd253 their mechanic did, not me.

[@TheGaryNinja]

Do I need to pay the dealership to reprogram after I replace the PVC? I purchased a 2013 Altima from them..Covered by warranty or recall?

[@DallasAutoDiag]

Yes

[@briandm33]

I'm trying to figure out whats going on with my 2015 Nissan Altima while I excelerate to go faster the excelerator knocks or makes a weird feeling on the foot petal while excelerateing. I was told that the transmissions on this series starts to go out in them or fail after the transmission gets about 80,000 miles on them and my car is right at 78,400 miles. So does anyone know what the problem is? I just got a tuneup on it a couple days ago and it still does this hiccup every once in awhile while driveing it.

[@DallasAutoDiag]

Why don't you take it to a transmission shop?

[@olguiq1013]

Does the computer reprogramming from dealer extend to the 2011 Altima 2.5?

[@DallasAutoDiag]

Yes

[@patrickseamster7967]

For the 2013 Nissan Altima what is the stock number for the mass air flow sensor

[@DallasAutoDiag]

Not sure.

[@myrdeazjah3497]

is the intake air temp sensor the same thing as a maf sensor? i was told those codes were affecting my car from starting up. i have a 2014 nissan altima.

[@DallasAutoDiag]

Those codes would not stop a car from starting

[@josebarrientos6034]

Is there any chance you have an idea on what's going on on my 2015 Nissan Altima 2.5? When I shift to Drive or Reverse, it won't move like if it's stuck on neutral.

[@DallasAutoDiag]

Signs of a bad trans. Take it to a transmission shop to be looked at, not a mechanic shop

[@iiDangleYT]

So if the pcv valve was already changed and the output voltage from the Maf is good then that means the maf is good? Then that means the ecu needs to be reprogrammed?

[@DallasAutoDiag]

I have noticed that reflashing the pcm is a must to get rid of this code.

[@elprofee2937]

Programming the ECM changes the parameters of when the code will set , once the correct PCV is installed and programmed, you shouldn't have any more P0101 code unless yoi have Drive ability issues then tsb doesn't apply

[@haribo3921]

@@DallasAutoDiagdo you mean the error code went back on in your case? Thank you!

[@mohammadsafi2348]

Hi thank you for the nice video I have a similar issue that I don’t know how to resolve I have a 2016 Infiniti QX60 SUV no check engine light on. all monitors are ready car drives fine but there’s a permanent code P0101 that will not erase and I’ve drove the car like 3000 miles. I need this code to be erased from the computer so I can smog the vehicle. ANY ADEAS YOU CAN SHARE? Much appreciate it

[@DallasAutoDiag]

You may have to reprogram your PCM to solve your problem.

[@aI-bv2zh]

Hi brother I got a question for you I got 2016 Nissan Sentra the engine light come on it says mass airflow sensor I replace it for time and still the engine light come on can you give me some advice thank you

[@minombreeslos]

I have the same issue with a 2014 nissan sentra. the TSB for it is NTB16-027A

[@taeshunsanders2187]

I went to get my transmission replaced with new transmission and now my transmission is slipping again.. very stressful situation..I don't have the money to get the diagnostic checked but if you can tell me how to check to see if my transmission was done.. 2016 Nissan Altima

[@blackqueenstudio4783]

Hello We got the transmission replaced for free at the dealership. It’s some type of recall for the CVT that extends the warranty for the Trans to 85,000 miles. Hope that helps.

[@alexarriaza2339]

You need to reprogram your transmission

[@taeshunsanders2187]

@@alexarriaza2339 how

[@taeshunsanders2187]

@@blackqueenstudio4783 i did aswell they put nothing new in just kelp my car fir 2 months and wrecked it

[@wmf1595]

Do you know if there's a similar technical bulletin for a 2011 Nissan Altima

[@DallasAutoDiag]

It should be the same case.

[@chris100ization]

Im so mad I just seeing this!! I just replace throttle body, gasket, and PCV VAVLE

[@henrytom5824]

Damn research first bro never start replacing everything good luck. 👍

[@hulong0205]

It's wired, your "11810-EA200" valve, on Nissan's website, it says fit 3.5L engine. And it suggests "11810-1KC0A" valve, which is orange. I just installed this today. The one installed by Nissan dealer about one year ago was "11810-6N202" valve (due to MAF error code). It's for 2018+ Altima. So confusing... Mine was 2013 Altima SV, 2.5L

[@DallasAutoDiag]

Its not weird the manufacturer comes with weird decisions

[@hulong0205]

@@DallasAutoDiag I found the correct part number on the bulletin. It’s 6N202. It’s all black, not the thread and the tip. But I don’t see why the green one will not work. Or even the orange one.

[@christopherrupengliang6662]

@@hulong0205 did you have to reprogram pcm or drive awhile after changing to the black one?

[@hulong0205]

@@christopherrupengliang6662 no need.

[@MinhPham-pm8vk]

Hulong, did you end up install the 11810-6N202 on your 2013 Altima 2.5l ?

[@acesup1456]

I live in Ohio but when I go to Tennessee or any where south. My 2015 Nissan Altima has a acceleration issue. After driving a while I stop at a light and I have to stomp on gas pedal a few times to get it to go. Any idea what would cause it. It doesn’t do it when I’m in Ohio only in altitude changing places.

[@andrewsowards1207]

Usually that would be a problem for carbureted cars

[@DallasAutoDiag]

Not sure honestly. A tech has to scan it and see if there are any codes.

[@mrperry6893]

Good videos man ‘ I need to ask you a question

[@DallasAutoDiag]

Go ahead

[@aapsuspensions]

New subscriber here, what model Autel scanner do you have if you don’t mind me asking?

[@DallasAutoDiag]

MS919

[@michaelchavez1043]

Do I replace orange pcv valve with black one? Does it have to be from dealer? What do I have to reprogram once i change the pcv valve?

[@DallasAutoDiag]

Buy from dealer. Update the pcm

[@michaelchavez1043]

Ecm or pcm?

[@yohanonshine4664]

All nissan 2.0 and 2.5 get this code because poor design of pcv system. It draw smokey oil fumes through air cleaner which often micro sprays into intake getting the sensor dirty and or dirty throttle body . I have also found rodent nests in intake pipe that cause the same code. Also causing this code is cracking in the flex pipe before the throttle body. If it was electrical problem you would have many other codes particularly oxygen sensor codes.

[@DallasAutoDiag]

Nice tip 👌

[@jcast7517]

Damn you must live in Brooklyn too Smhh … damn rodents !

[@omarct]

What can i do to fix it? Im tired of cleaning my throttle body.

[@jeremiahpaul1340]

I changed out my maf sensor out but the car still didn't get better the check engine light didn't come back on but the code I got was po101 on a 2012 Nissan Altima

[@javieralcala9805]

Hello, when you changed the part of your car, you reprogrammed the computer and if the smog check passes, let me know, thank you

[@washingtonpesantez6311]

If I don’t have a scanner how do I delete the check engine light when the job is completed??

[@DallasAutoDiag]

Try disconnecting the battery negative. Then pump the brake twise while negative disconnected. Then wait for a minute or so and reconnect.

[@washingtonpesantez6311]

Thank you do you think I have to reprogram after I change the pcv valve is is orange in my 2013 Nissan Versa ??

[@DallasAutoDiag]

@Washington Pesantez most of the time, you have to reprogram.

[@tdgarza2000]

I wish you were here, i keep forking out m oney, replacing the mafs and still no acceleration and engine light nissan keep trying to get money out of me

[@DallasAutoDiag]

Find a local guy to update your pcm software.

[@l.a.w.6494]

Im getting that code, but my car comes on in park or nuetral but immediately shuts off when i put it in reverse or drive. P0101 only code I get Nissan Altima 2014

[@DallasAutoDiag]

I would start with pcm update. I don't think the code has any thing to do with car shutting off though.

[@vladd1593]

2012 Nissan Altima s2.5 P0101 codes keeps coming back after two weeks consistently, the sensor is already replace.

[@DallasAutoDiag]

Did you update your pcm?

[@vladd1593]

@@DallasAutoDiag the owner has not updated the pcm. But the p0101 code comes back after 14days each time I reset the code. Could this be the pcm or needs a module update?

[@DallasAutoDiag]

@@vladd1593 you have to update the pcm and make a decision afterwards.

[@vladd1593]

@@DallasAutoDiag will do the pcm next. Thank you so much for your input

[@washingtonpesantez6311]

How do you reprogram the computer after the pcv is change thanks

[@DallasAutoDiag]

Have to have nissan tools and subscription to do so.

[@washingtonpesantez6311]

Ok thanks I think I have to bring to Nissan dealer to reprogram

[@kinanlaham744]

PCV valve caused a MAF sensor circuit code!!

[@DallasAutoDiag]

electric is weird

[@washingtonpesantez6311]

Do I need to reprogram my Nissan Versa 2013 ??

[@DallasAutoDiag]

Most probably yes

[@b5rs424]

2017 Altima delay when gas is depress. Any clue? Ty in advance

[@DallasAutoDiag]

Any codes?

[@b5rs424]

@@DallasAutoDiag no codes on dash.

[@javierpaez613]

Problem is the mass sensor period.

[@DallasAutoDiag]

thats one of them. watch the video

[@AEA570]

انا عندي نفس العيب هل تعرف حد في نيوجيرسي يصلحه ؟ شكرا.

[@DallasAutoDiag]

take it to the dealer. it shouldn't be much

[@ayoubelmaskine1987]

So no more P0101 code after the customer left?

[@DallasAutoDiag]

Only the trans code.

[@SOHAIL50280]

Brother I have Tha same problem with my nissan sentra 2019 same code is coming in engine pcm i change mass air flow sansor remove from other Santra my run too good Tha same sonser I putt other Santra it not running well I change new sonser butt Tha car is not run it go on 60 km

[@DallasAutoDiag]

you need to update the pcm

[@rlt7409]

You said something about reseting the computer, were you talking about the OBD2 or you're talking about the ECU?

[@DallasAutoDiag]

No obd2. You have to reflash the ecu software.

[@tylerjacob3141]

By any chance do you have the link or know where to find the tcb

[@DallasAutoDiag]

Just Google the number that I mentioned in the video

[@SifuFreeGamer1417]

My car keeps shutting off , I went to the nissan mechanic and he said it's something with the battery .

[@DallasAutoDiag]

Did you change it?

[@bigglokk1975]

Anybody can help me what does code p0102 p0962 &P0112 on a 2014 Nissan Altima 2.5 ?

[@DallasAutoDiag]

My advice to you is take it to a professional technician

[@1030barca]

How can I find the ECM part number for mine?

[@DallasAutoDiag]

There is a sticker on the side.

[@Martin..........]

Altima 2013 and Altima 2016 is the same motor?

[@DallasAutoDiag]

yes

[@keysautorepair6038]

Was exactly was it doing like dying

[@DallasAutoDiag]

Check engine light was on

[@jpadilla0515]

Shit my niece just paid to have it reprogrammed. Check engine light name back on need to replace that part

[@DallasAutoDiag]

yup

[@javieralcala9805]

Hola yo tengo el mismo problema en mi carro hoy lo yeve hacer el smog check y el codigo p0101 salio que no pasa y el mecanico me cobra 450 por arreglarmelo porque segun tiene que reprogramar la computadora es verdad

[@DallasAutoDiag]

was the code gone after programming?

[@mustaqrahim9055]

need a valve body there bro

[@DallasAutoDiag]

Not necessarily

[@mustaqrahim9055]

was talking about about the p17f1......................@@DallasAutoDiag

[@yoitsraul15]

Any Southern California mechanics in here that could help a brother out with fixing my 2016 Altima per this TSP? 🙏🏼💯

[@DallasAutoDiag]

What's your zipcode?

[@yoitsraul15]

@@DallasAutoDiag 90262

[@mariopasapera5709]

Hi ...can anyone help me with this I'm in Miami west kendall

[@DallasAutoDiag]

What kind of help do you need?

[@rickyrush3042]

Where are u located in business name

[@DallasAutoDiag]

In Kennedale TX

[@nickayivor8432]

👍 My Mentor Dallas Auto Diag ACCOMPLISHED Dallas Auto Diag Take care and have a great evening with all your family around you ACCOMPLISHED Dallas Auto Diag From Nick Ayivor from London England UK 🇬🇧 ⏰️ 18:52pm

[@DallasAutoDiag]

Thanks Nick

[@jpadilla0515]

Why the hell do you have to reprogram for a pvc lol wth nissan

[@DallasAutoDiag]

change what the pcm is looking for in order not to trigger the check engine light

[@jpadilla0515]

@DallasAutoDiag thanks for the reply. Would you happen to know once we replace the pcv do I have to have it reflashed?

[@DallasAutoDiag]

@@jpadilla0515 follow the tsb. In most cases you do

[@corelltemple2939]

Bruh, you explained NOTHING. Just a bunch of mindless talking. 👎🏾

[@DallasAutoDiag]

Sir I think you did not watch the whole video. In the video i am following a Technical Service Bulletin TSB that was released by nissan regarding this issue.

[@jamesmurray9806]

Make sure you take your car in for repair. You don't have a clue.

[@embroideristalavista6485]

This was a very thorough, very comprehensive explanation. It explains how to eliminate outliers and whittle down to the exact problem. If you don't get it, that's on you.

[@johngraham2470]

Seems you don`t have patience to watch entire video.

[@gettyfernandez5428]

He explained more than most people would. We go through allot to diagnose problems that most people couldn't even imagine.

[@TAC40_]

It also needs a trans lol

[@DallasAutoDiag]

😂

[@MrHmax01]

Hay man thanks for the awesome work you did 👏... I know that guy my best friend [FIDA] the owner of the car he used to leave in Saint Louis MO about 10 years ago he moved to taxes if he comes back say hi 👋 to him from me (Hamid)

[@DallasAutoDiag]

Hi, yes that was Fida lot. Fida is a good guy. I will tel him you said hi next time I see him.

[@olguiq1013]

Does the computer reprogramming from dealer extend to the 2011 Altima 2.5?

[@DallasAutoDiag]

Yes

[@olguiq1013]

@@DallasAutoDiag Thanks