Full service on Panasonic RX DT 75, CD unit ,SUBSCRIBE ,LIKE, COMMENT, SHARE, ENJOY
Пікірлер: 21
@antoniodacosta19914 ай бұрын
Merci pour votre patience et votre aide, maintenant je pars dans ma famille, j'essaie la réparation en Mai. Bon courage pour votre travail, moi je suis retraité.
@cicerogoncalves37514 ай бұрын
😮
@antoniodacosta19914 ай бұрын
cet après midi j'ai acheté un voltmètre. pour faire la mesure de continuité de la diode, le lecteur cd doit il etre branché sur le courant ?
@blingonit4 ай бұрын
The cd player don't have to be connected to the main unit ,remove all the electronics board like i did in the video ,put the multimeter in diode test mode ,until when you cross the black and red wire of the multimeter there is s a bip sound coming frim the multimeter ,after that you can all switches , put the multimeter red and black on the switch terminals and press the switch it should make bip if all is good
@blingonit4 ай бұрын
In the previous video i clean and test all the cassette deck selector switches, it's the same procedure,,but to be sure buy only G22 cleaning spray , this will clean well oxidation and leave no residue,and please download the service manual from internet ,i wait a good news , good luck with your repair
@antoniodacosta19914 ай бұрын
je dois partir demain en voyage dans ma famille au Portugal, je voudrais savoir si je peux faire tous les tests de la diode et des moteurs avec le voltmètre sans que le cd soit branché sur le courant. Si c'est pas nécessaire qu'il soit branché je vais le démonter et l'emmener avec moi pour travailler dessus. Merci de votre réponse
@blingonit4 ай бұрын
You can test all the motors and all the switches with the cd player unit of the frame , like i did in the video
@blingonit4 ай бұрын
Yes
@antoniodacosta19914 ай бұрын
Bonjour, j’ai regardé votre vídeo et je l’ai suivie pas à pas . A la fin j’ai ressoudé les moteurs. Maintenant lorsque j’inséré un disque il ne tourne pas pour le reconnaître’ il me dit à chaque fois pas de disque. Pouvez vous me donner une indication sur ce que j’ai fait mal? Même si ça sautait par moments je crois que j’aurai pas dû y toucher car je ne suis pas aussi doué que vous.
@blingonit4 ай бұрын
1 ,measure for continuity the two switches on the front right of the drawer, this tells the processor there is a disc inside and activate the laser and spinning the disc , 2 take out the metal top of the assembly and open and close the drawer,watch if the laser comes on or try to focus . 3 clean gently the lens maybe oil drops accidentally there , 4 check if al connectors are in place ,good luck with repair
@blingonit4 ай бұрын
I couldn’t sleep and I thought another check you can make just to be sure so , in the video at 17:15 is a little switch ,take the bord off and check the little switch so is not broken after that locate the near the left motor that move the laser assembly a little white gear , rotate the gear to move the laser about 1 cm after that put everything together and don’t forget to solder the two motors
@antoniodacosta19914 ай бұрын
Que veut dire mesurer la continuité
@antoniodacosta19914 ай бұрын
J’ai retiré la partie métallique, ouvert et fermé le tiroir, et la lentille ne bouge pas du tout, aucune impulsion
@antoniodacosta19914 ай бұрын
merci pour votre aide, a 17h15 ce n'est pas possible car votre vidéo fait 17h17 au total.