PANDEMIC LED Tail Light Conversion KIT Install

PANDEMIC LED Tail Light Conversion KIT Install
This kit is amazing! Install went really smooth and they work amazing! its a little tough getting those lights to slip into the housing but just don't be afraid to use tons of that soap to get them to slide right in. If you have any questions at all shoot a comment below and I will get right back to you.
Get yours here: www.pandemic-usa.com/Pandemic...
Help Support the Channel via Patreon: / thebeardedjeeper
My Gear:
Camera: goo.gl/Ga51VD
Lens: goo.gl/CRHSJP
Other Lens: goo.gl/WhpC1b
GoPro: amzn.to/2H1Z9ta
Mic: goo.gl/WbnjAf
goo.gl/9D7wbp
Email: [e-mail]
Find me at these other places on the internet:
Facebook: / beardedjeeper
Twitter BeardedJeeper?lan...
Instagram: / the_bearded_jeeper

[@walterhughes5765]

Kyle thanks for this video my next project ordered them today great job .

[@TheBeardedJeeper]

Glad it will help. If you have any questions hit me up. Kinda nerve racking cutting up the body

[@howiediy9917]

The tail lights look good. I know the struggle of putting in those type tail lights all to well. Also I have been using those wire connectors for a while now. A heat gun makes quick work of them. They work well as long as they are not in an area that gets too hot. Thanks for the video.

[@TheBeardedJeeper]

Thank you! And those connectors are awesome. I need to get a heat gun to make quicker work of them. The tail lights are super bright I love them. Thanks for watching

[@ProjectDanH]

I'd love to retro fit these into an XJ. Great vid buddy!

[@TheBeardedJeeper]

Project Dan H thank you sir! Yeah they would look sweet on an XJ. Maybe we can convince them to make a set for XJ too I would be the prototype

[@kyleseaver9497]

Thanks for this awesome step by step, should be getting mine next week!

[@sugarmagnolia3477]

Looks great! I love the flush design of these!

[@TheBeardedJeeper]

sugarmagnolia3477 thank you. I do too they are super bright too

[@DEInTheGarage]

Awesome to see you working in the garage!

[@TheBeardedJeeper]

its so awesome to have a garage again. I love it!

[@Jeep.Generation]

That looks sharp. Nice install video.

[@TheBeardedJeeper]

I agree and thank you

[@JKsouthwest]

Great job on the install! The new lights look great

[@TheBeardedJeeper]

JK southwest thank you 🙏 and I agree these lights change the whole look of the rear of the jeep. Looks great

[@zerolimitsoffroad6346]

Cool video bro. Very informative. See you on the trails!

[@TheBeardedJeeper]

Thanks for taking the time to check out the video. See you on the trails someday

[@zerolimitsoffroad6346]

@@TheBeardedJeeper yeah man.. I've been kicking around the idea of this conversion kit, but every time I'm ready to pitch the idea to the wife, something else needs fixing... pitman arm, drag link, tie rod and all ends... you know how it goes...

[@danhambrick6331]

Damn you got some good audio.I heard a lawn mower and a train even over the back ground music...lol...

[@TheBeardedJeeper]

Dan Hambrick yeah in the garage it kinda picks up the sound really well. Rode video mic go. I love it. Thanks for watching

[@AviatorMilo]

These tail lights are super appropriate right now

[@DEInTheGarage]

That is sick man! Looks so much better than stock. Wranglers get the coolest stuff!

[@TheBeardedJeeper]

I agree I love it! Dan and I were talking about seeing if we could retrofit them on a cherokee

[@DEInTheGarage]

@@TheBeardedJeeper That would be awesome

[@TheBeardedJeeper]

@@DEInTheGarage maybe we can get pandemic behind it to make something

[@TheBeardedJeeper]

These tail lights are super bright! I love how awesome they look too! Drop any questions you have below. Thanks for watching!

[@Casey250]

Me and my tail lights didn't work out so well on my corner armor even with dish soap lol.

[@TheBeardedJeeper]

guess you need more dish soap haha

[@partyboy0319]

How do you pop it out when it goes bad

[@TheBeardedJeeper]

You just push it in on one corner and pop it out

[@macktaylor4389]

Are these lights DOT-approved?

[@zachharper216]

you need a load resistor to prevent the fast blink? Does that go for single LED bulbs as well? I was hoping I could buy LED bulbs without all this. Different model of car tho. Good vid, thanks

[@TheBeardedJeeper]

yeah you need the load resistor on the single bulbs as well. I wish you could just turn off that function

[@btyme80]

Is there a gasket between the body and the plate?

[@TheBeardedJeeper]

btyme80 no there isn’t. I’ve seen some people put some RTV behind there. I wasn’t too concerned

[@allanwagner4570]

Ok soooo I been thinking bout moving my plate in the same manor as yours However have you ever had police hassle ya for it?? And how did you mount it ?? I can’t see any bolts or screws??

[@TheBeardedJeeper]

Allan Wagner haven’t got any haste for it yet I mean it’s in the stock location just bent around the body. I made a video on how I mounted it. kzbin.info/www/bejne/qpCrgmZtiJmUg9k

[@glennpeck471]

How expensive are they?

[@TheBeardedJeeper]

Glenn Peck link is in the description. Price changes depending if you want the harness and the load resistors

[@Gtown1970]

Where did u find the factory harness with the 3 pin already with it

[@TheBeardedJeeper]

They did have them on the website for a little bit. They were out last I knew not sure when they are getting more

[@Whiteandsonsgarage]

Awesome video mate, they look so good, sometimes my wife comes in handy when working in my Jeep

[@TheBeardedJeeper]

thanks brother! I really like the look of them as well. If I didn't have the wife help make sure they were straight they would be crooked for sure haha

[@joeteasley9428]

Where can I get the plug n play harness?

[@Rockridge4WD]

The harnesses will be available again in the next week or so. It will be available on www.pandemic-usa.com or www.rockridge4wd.com

[@paulpecorella408]

Where can I get the easy wire harness from that u use in video

[@TheBeardedJeeper]

Paul Pecorella you can order them with the kit. It is one of the options when you order you can select the plug and play harness

[@paulpecorella408]

The Bearded Jeeper does not let me choose if I want harness or not

[@TheBeardedJeeper]

Paul Pecorella that’s strange it should let me contact them and see if they don’t sell it anymore

[@paulpecorella408]

The Bearded Jeeper let me know if u can find them

[@TheBeardedJeeper]

Paul Pecorella will do. I will let you know as soon as I get a response

[@momo-yz4lu]

Nice job looks good. but no way is this kit worth the 285$ lights, metal bracket, resistors & screws. All can be purchased for under 75$ on eBay

[@Rockridge4WD]

It is certainly an option to attempt a DIY kit. I say go for it! This is for the guy thay wants a nice laser cut aluminum, cnc formed and powder coated plate. Time is money and if you have the time, save some money!