How-to Fix Samsung CLP-360/365W, C410W/C430W • Paper Jam/Won't Pick-up • Detailed Printer Repair!

[@GTCSRobert]

Thank You Paolo. I followed these steps and my C460FW is now working. I can't thank you enough!!!!

[@wongdiggy]

Wow, it is such an informative video. This fix gave my printer a second chance in life. I had to watch and rewatch it a few times. There were some tips missing like getting the front panel off and using a swiffer dry static wipe to clean up toner, but this nailed it so well, I could not express enough gratitude for you posting the how-to repair video. It's thankfully not too difficult.

[@acewindbreaker]

I want to thank you for this excellent video! I have the C410W version and it didn't pick up the paper, and just as you described, when I used a flashlight to look into the printer I could see that it stood still inside. I found a solenoid on a websight in China, and ordered it from there, the cost was redicolous, about 8 Euros including getting it in my mailbox. Following your instructional video it was quite simple to change the solenoid, and after putting it all together again, the printer worked perfect!! So once again a big THANK YOU!

[@AndrewFrance]

To add to the chorus, thank you so much for this video! Our Samsung CLX-3305FW has been having trouble picking up paper for years, leading to much frustration, until last week when it finally totally stopped! Thanks to the other comments here I didn't try to remove and replace the solenoid but simply removed the lower pad and taped the lower and upper areas with a tiny amount of electrical tape. I hope Samsung have rectified this design issue in newer models as otherwise the printer is pretty good and I'm impressed at the repairability.

[@Dude-t3o]

Thank you very much, Paolo! I tried so many things until i found your repair guide. At first i hesitated to try it myself and wanted to find a Samsung/HP repair service in my area, but they refused to repair it. That brought me to try the repair by myself and it succeded. My C480FW works again. I'm glad you took the time to explain and show the solution. Thanks again.

[@lennertheilmann8474]

Thank you for the great tutorial! After 8 years of service, my Samsung C410W would only take in the paper half way and then get suck on the first print-job. I always had to pull out the paper and restart the printer to make it work properly again. I removed both pieces of rubber from the solenoid and replaced them with some rubber from a bicycle tube, which I attached with double-sided adhesive tape. Now the printer works like new.

[@miguelortega9192]

Wow, you really saved my printer. Thank you so much for that wisdom :) I wish I could help others as much as you someday!!

[@bb7743]

Paolo, your video was great! I would never been able to diagnose nor fix my C460FX without it! Your instructions were perfectly detailed--I watched your video before I started the repair, and then watched it again (with lots of pausing!) as I stepped through the repair. I did not replace the solenoid, but like others, but put a mylar label on the rubber pads to prevent sticking (even though the pads did not seem to be breaking down). I crossed my fingers and it all worked after I put it all together. The repair took me about 2 hours in total--I wish I was as proficient as you. Thanks again for this great video! Bud

[@PaoloMarcelli]

Thank you bud, great job :)

[@marctre1]

Thank you, my printer has been inactive for more than a year because of this problem. Took me about an hour and now it is working even better than before it broke (it gave errors about having to change the imaging unit and now it doesn’t). You’re awesome!

[@PaoloMarcelli]

Thank you :)

[@gerardlapierre2820]

Many thanks from Paris. Everything works after having changed the solenoid.

[@parmmohan4603]

Same. Just changed it last night and works great!

[@hermesnetwork]

Thank you so much for the detailed video tutorial. I was able to follow your instruction and fixed my Samsun C410W printer pick-up issue after replacing the JC33-00025B Solenoid. You're great and I'm very grateful for your help!!!

[@Ravi-vp4qm]

Excellent fix for Samsung CLP410W color Laser printer (US) . Step by Step instructions,pretty cool. Instead of throwing away the printer and ending up in a landfill , this is a better option spending 30 minutes of your time to fix it. worth it. Kudos to you dude for saving the environment.

[@PaoloMarcelli]

Thank you so much :)

[@Indiestereographer]

Thanks Dude - 10 euros to fix my printer - much better than tossing it in the garbage and buying another one - you're helping to save the planet my friend!

[@PaoloMarcelli]

That's one of the biggest reasons I make these videos :) help people fixing their stuff (and learn in the mean time how things work) and help reduce e-waste :)

[@Mike95inNJ]

Thanks pal. I'm a copier tech and have run into these issues in the past. We usually put a small piece of self stick mylar on the two sides of the solenoid. Trash picked a C410W that only had 769 prints through it. I put the mylars on and now I have a pretty much new printer. It was nice having your video to follow for the disassembly. Helped a lot. Cheers.

[@SladjanIlincic]

Could you please explain or make sketch of place where did you put foil? Have same problem with printer.

[@Mike95inNJ]

@@SladjanIlincic I put little pieces of self stick mylars on both sides of the solenoid where the rubber is. Cover the rubber pieces. Cut them to the same size as the rubber.

[@robertmeert9564]

A big thank you for this very well detailed tutorial. By following these explanations, I was able to repair my printer which will take on a second life.

[@jurgkos809]

Auch mein Samsung-Drucker hatte keinen Papiereinzug mehr. Ich bedanke mich für diese exzellente Anleitung zur Demontage und anschließend zum Zusammenbau 😊 🙏 Allerdings: Ich folgte der Anleitung vollständig bis auf ein Detail: Ich tauschte das Solenoid NICHT (…denn ich hatte kein neues gekauft.) Ich prüfte das Selenoid auf elektrischen Durchgang: es war in Ordnung, ca. 120 Ohm. Auch mechanisch entdeckte ich keine Mängel. Also baute ich genau dieses „alte“ Solenoid wieder ein und folgte der Anleitung zum Zusammenbau. Dann prüfte ich den Drucker und war auf das Angenehmste überrascht: Er funktioniert wieder (bis heute…) tadellos! 😊 Das Solenoid in meinem Drucker war offensichtlich gar nicht defekt! Meine bis heute nicht geklärten Fragen: 1) Was sonst hatte zu dem Defekt geführt? 🤔 2) Was könnte durch diese Demontage + Montage unbemerkt „geheilt“ worden sein? 🤔

[@andersjonsson1874]

Thanks! Did this on my C460w. I also lubricated the tap on the inner gear wheel to reduce the friction between solenoid arm and the gear wheel. I removed the little top foam piece and replaced it with double adhesive foam tape but left the top plastic on the tape stay on. Worked perfect after 2 years of fighting this printer and almost giving up.

[@marcofebbo4096]

so, is the solenoid on the alibaba link compatible with C460W?

[@kristian.gustafsson]

Thank you! You saved the life of my CLX-3305. I can now print again after 1,5 year 😊

[@PaoloMarcelli]

Great job for fixing your printer :3

[@aldosvampa8630]

Thanks Paolo, The video is very good and clear, greetings from Argentina.

[@BernatLlorenç]

Great step by step tutorial. It allowed me fix my clp-365w printer. Thank you very much Paolo! 👏🏽👏🏽

[@bartekpaluch4474]

Thanks for saving my time and money. I have only disassembled, touch the solenoid couple of times, and assemble it again. My printer was resting for like 2 years so maybe it just wanted a little touch... Thanks, good job.

[@juhakera4646]

Thank you very much, indeed. My Samsung C460W run into this paper jam problem and I managed to heal the it following your very good instructions: Actually I replaced the whole unit JC93-00547A but I ordered a solenoid, too and shall prepare a spare part from my old JC93-00547A for my neighbour who owns a similar printer.

[@dearme5660]

Thank you! This was very easy to follow step by step procedure, and it has a very detailed explanation.

[@bnenm9310]

Worked for my Samsung C460 too. For just one 4$ part such a procedure. Thanks for you video, helps a lot.

[@jwilkinson341]

I got it off there were inner ones close to the middle, I put it all back together and it works I had my doubts, many thanks for this detailed video

[@nicolatompkins6517]

Thanks for the video. It helped me change my solenoid sensor and now my printer is working perfectly. 👍

[@elenafedeli]

[@weigefans]

great video to demostrate the reason why happen the issue, also great solution to fix it! great!

[@nicolaschiaruttini8450]

Awesome, you saved my CLX-3305W for 5 bucks, and a bit less than one hour of work, thanks to your perfect tutorial. There's just one tiny thingy stuff on the right that needs to be pushed when removing the front panel on my model (at around 5:21 on the video). I followed exactly the tutorial and found the new solenoid on digitec (article JC33-00025B, it took a few weeks to arrive).

[@marchoschele6513]

Hello Paolo, many thanks for this great repair manual, now - after 6(!) years of having this printer standing around not printing and not wanting to give up, I finally found your video - many many thanks - it works perfect. I have even found out that its not magnetic adhesive, but simply a slightly glueing soft bumper that starts to glue on soft pressure. So I put on some Tesa onto it to make it smooth and non-sticky and now it does not glue anymore even after pressure and works perfectly well now. So its even a 0.0 Euro repair! Many thanks and bravo bravo to you

[@PaoloMarcelli]

Thank you and great job for fixing your printer!

[@paddy1068]

Paolo, thank you so much for this detailed video!!!! 🙏It only took me about one hour to repair the printer. I was not sure this was the reason, but obviosly it was. The printer is up and running again. 😊

[@robertconnier9457]

Fixed my CLX-3305FW using this instructional video. In my case, the solenoid had died (open circuit), as the pad on the original solenoid was not sticking at all. If you wear magnifying glasses, it helps a lot to see the small parts clearly.

[@lwcmy]

Thank you for your sharing. You saved my printer with a small spare part. My printer is C480W, slight different structure but your guide is adequate for me to repair mine.

[@davidng9354]

Hi Wee Chang, my printer is same model as your. Is the solenoid part no. you purchase is using same as what he recommended?

[@lwcmy]

@@davidng9354 ,yes, i bought from here: www.aliexpress.com/item/4001143446682.html?spm=a2g0s.9042311.0.0.16b84c4dhReECs

[@barbarahenninger6642]

Thank you for a very easy to follow video! I will try to fix my printer following your excellent instructions!

[@oldengguy]

Thank you. I just picked up a CLP-365W marked $7.99 at a thrift store, and it has the same symptoms. Everything else installed properly. Your video has convinced me I can open this up and do this. I'm guessing it will be exactly the same problem.

[@PaoloMarcelli]

You can definitely do that :) also other users said that in their experience it's not needed to replace the entire solenoid, just the two foam pads :)

[@oldengguy]

@@PaoloMarcelli I pulled out the solenoid, checked to make sure the resistance was right, and worked with it to make sure it was clean and free and that those pads were not sticky, put it back in place, and the printer is working great. It didn't cost anything except a bit of time.

[@jor10002000]

Thanks Paulo, your video is clearly well explained. I dissassembled the printer before ordering the solenoid and on the way I found some plastic chips that were preventing the right movement. Your instructions were capital on finding and solving my issue. Thanks again.

[@PaoloMarcelli]

Great job :) By the way, as you can read from the channel name, my name is Paolo, not Paulo XD

[@DrThalamic]

Thanks for the info --- I purchased a Samsung C460W for $20 that wasn't working due to a paper pickup issue. The steps for this unit were very close to your demonstration, however when it came time to pull the 4 sets of wires through the hole this unit had a small hole and I didn't bother passing the wires through. I proceeded to cover the foam on the solenoid (still attached to the unit) with Kapton tape and reassembled the unit. The solenoid was fine, it was just the foam that broke down and became adherent so by covering the foam with Kapton tape the problem was resolved.

[@CpaMoya]

Paolo. La impresora no tomaba el pepel, estaba pensando en botarla a la basura. Encontré tu video, y la verdad, es excelente. Te agradezco por la claridad y exactitud en cada proceso. Ahora puedo seguir usando la impresora. Me ahorraste de comprar una nueva. Muchas gracias y saludos desde Santiago. Chile.

[@PaoloMarcelli]

😊

[@lorenzofiumalbi8705]

ciao paolo e grazie!! i just fixed my clp-360 with 3 euros. the best part is that i received that printer for free because wasn't working!!

[@jorgsteinke1140]

Awesome! Thank you so much for this detailed and handy video. I fixed my Samsung CLX-3305FW with this guide.

[@PaoloMarcelli]

Great job! :)

[@stacksweaver]

Followed the steps and my printer is printing again!!!! Thank you!!!!

[@Kornel1100]

It worked for me as well. Thanks for making as little steps as needed. This took me about 1,5 hours, so not much at all.

[@PaoloMarcelli]

Great job! :)

[@jayanour]

Wow! Thank you very much for your life-saving video. I know now what to buy to fix my printer. It seems that the solenoid is a common problem for Samsung printers. Keep up the good work and stay safe.

[@Pin-hy1di]

Thank you so much. Really works.😀

[@PaoloMarcelli]

Thank you so much for the donation

[@dmartin4707]

Most excellent instructions! Lazarus C430W raised from the dead.

[@pulsarfox]

Thank you mate ! Thanks to you, my doctor's C410 won't go to the trash.

[@anthonys555]

Thanks this worked for me. Instead of removing the rubber I put nail varnish on which still didn't work. What worked for me was super gluing a couple of layers of card on top of the nail varnish so that the gap between the solenoid and lever was a bit closer. 2 layers did it for me. 3 layers was too much and the plastic gear was not being held. Works perfect now.

[@davidstainsby8927]

I had the paper feed problem, i found your video, purchased a new relay, hey presto it now works ok, thanks for your informative video

Wonderful! Thankyou! Worked perfectly for me and my C460w. Like others, I fixed the solenoid instead of replacing it. the Rubber pad had drifted a bit and was no longer touching the "counter flange" that the rubber pad should bounce agains. I moved the rubber pad back tow where it was supposed to sit and also bent the counter flange a bit downwards to make the arm not swing as var from the solenoid. Everything seems to have worked.

[@mdiferdinando]

fatto da sola , sei stato chiarissimo. Ho risparmiato più di 100 euro che mi avevano chiesto x la mano d'opera ,e vuoi mettere la soddisfazione? super.

[@vadimbyallcare6352]

Thank you deep !!! In my case the Model is Xpress C480FW. But everything inside is almost the same. The printer do not want to pick up the paper. This tutorial helped me a lot to proceed with the deep cleaning.

[@laurensijsselmuiden6696]

Amazing video! Thanks for showing how to repair my Samsung CLP-365w. I ordered the Solenoid and am curious if that will solve my paper error. Thanks again for this tip!

[@jerryk7745]

Great video, thanks Paulo. I was ready to go ahead with your fix, but could not see clearly if the roller was turning. So I took out the paper tray and then propped up the front of the printer about 8cm. Then the roller is not only visible but also accessible to clean. There is a little plastic tag to the right of the roller which detects the paper tray. if you press the tag and use a torch you can see the roller turning to try to feed when you press copy. Also a good time to clean the roller with a cloth soaked in iso-propyl alcohol. Be careful roller does not grab the cloth if you try this! Two other points your viewers might like to check: Place the tray and paper in a warm dry place for 24 hours. It's surprising how much humidity paper can absorb - this affects paper pick-up. Final point: make sure all the paper guides in the tray are snug against the paper - especially the one at the back of the tray (farthest from the roller). Doing all this got my printer working again without replacing the solenoid! Thanks again

[@parmmohan4603]

You made a awesome video!!! Saved me $500. Love you man!!! Thank you so much!!!

[@nemethzsolt5245]

Thank you the video! I take out the solenoid from the printer. I measured the solenoid with DMM, but the solenoid is good. The solenoid connector is the wrong (I cut the solenoid wire next to the connector and soldered it to the panel)!

[@RoelandMerks]

Thank you so much for the very clear explanation. It work like a charm for my Samsung XPress C460W on second try!

[@patrykf4993]

What solenoid symbol for c460w printer?

[@Kearwood]

Thanks for the great tutorial, fixed my CLP-360!

[@pamelapere]

I fixed my printer (with just 9€) !! Thank you so much 😀

[@janverdam5764]

Thank you so much for your video. It helped me to diagnose the problem and with your clear explanation I also could repair the printer. Perfect job!

[@kjaxky]

great job! What's is the difference between Samsung CLP-360/365W, C410W/C430W they'll look the same I know 410w/430W were sold in usa and canada but I cannot figure out differences at all

[@detjuk]

Great video, cleaning didn't help, but replacing the solenoid seems to have fixed the problem! Mine is a clx-3305fw from Samsung. Replacement part orderd on aliexpress.

[@davidrlin]

Thank you for your video. Mine really can’t hear any notice, like main motor not working or not heat up?

[@helmuthbosch7852]

Great video, this fixed my printer (CLX-3305FN). Thank you very much.

[@zozzo58]

Just worked perfectly on my CLX-3305 : thank you

[@PaoloMarcelli]

Thank you for watching and now throwing away your printer :)

[@fabiomarcon555]

Hi this helped me a lot even though I don't have the printers above I have a clp-315w the solenoid thankfully it is a little bit easier to get to and it was sticking because of the pad - removed the pad _ DONT NOTIC ANY DIFFERENXE IN NOISE and it works fine

[@gianniint8874]

Grazie per questo video fantastico. I tried to disassemble and just cleaned the solenoid without taking it out and re-assemled the printer (C410W) - Proble still persists but at least I have familiarised with the procedure. I will have another go at trying to fix the solenoid with rubber or something similar before I look for a new part. The JC33-00025B somebody mentioned here seems to be reasonable in price (+£ 6-7 for postage) but not sure it is the correct one. Will post back in due time. Grazie ancora Paolo. Giovanni

[@jorismk1]

Thankyou! What I did was use the old coil. It's not broken, just the pad is compressed and somewhat sticky. Remove the pad and clean, bend the metal lip to where the pad would normally stop the arm. Reassemble and done :) Only thing is it now clicks when printing (which I don't mind)

[@apantrasansson]

Good video! I have a 430W. The diagnostics report no problem. But the printing software claims that the "lid" is open. I previously got two error codes from it once - m1-1013 and m3-112.Still, it prints test documents pressing the "X" button just fine, just like you did to test the solenoid. But when I try to use it for printing anything else, it refuses. It does not even try to pick up paper. Just silent. Any guess to what might be the problem?

[@shmangtown]

Thanks so much!! worked a treat! Would have been a $150 repair but cost me $5 :) Really appreciate your video / help! :)

[@PaoloMarcelli]

Thank you, and great job for fixing your printer, the planet will be grateful to you.

[@francesconeri2550]

I used your video guide to repair my printer: thank you very much! :D

[@DeltaBlast]

This video was very easy to follow and allowed me to replace the solenoid in my CLX 3305FW. However, when I put everything back together, it didn't turn on any more. Just nothing on the display at all. I've retraced all the steps and did it all again, but I don't know what went wrong. Maybe I damaged the logic board? Do you have any clue what would cause the display to not come on at all? I even put back the old solenoid, but that wasn't the issue either. I opened the cover for the electrical parts but I didn't see any popped capacitors and that's the extent of my knowledge... Any help would be appreciated!

[@sorinpopescu3576]

Thanks for the video. Managed to fix my printer following this.

[@ataulghalib86]

Just fixed clx3305. Great video thanks

[@thomasgovender5874]

hi how did you fix it? Did you replace the rubber part of the solenoid?

[@bleb777]

Thank You for your guidenance. My printer is working after replacing the solenoid and paper is picked up like you said. Probably this little tiny spongy thing in solenoid is couse of troubles. OMG i am so happy!

[@PaoloMarcelli]

Thank you, good job for fixing your printer :)

[@Joost001]

Thanks a lot! Followed your instructions and my printer works like a charm again! :)

[@tarhanasevdas3399]

THANKS FOR THE VIDEO. I CHANGED THE PART. IT IS NOT RECEIVING THE PAPER NOW CAN THE TONER BE ENDED

[@adquestit6480]

Good job! you are very talented! I liked the way you explained the problem!

[@mipi_game]

Did this in my CLX-3305W and worked perfectly! Thanks!

[@joseantoniomartinez5423]

Paolo thanks God for your clear explanation. I solved the damage without any setback. Regards

[@davidweller8158]

Mega thanks Paulo, it may have cost me £15 for a new solenoid in the rip-off UK (£7.50 plus postage) but that is a lot cheaper than almost £300 for a wireless printer scanner. She runs again like new. Perfect for the C460W to add to the others.

[@PaoloMarcelli]

Thank you for your comment David :)

[@hvdlocht]

Thank you very much for the solution to this problem which also worked for my Samsung Xpress C460W. At first I thought it was the pickup rubber being dusty. But after seeing your video I noticed that the pickup rubber was not turning at all. It took me about 2 hours to fix it with help of your video (after waiting 31 days for the solenoid to arrive in the Netherlands), but now everything is running fine.

[@favers77]

Hi Henrie is it the same part number? I have the C460FW

[@patrykf4993]

What solenoid symbol for c460w printer?

[@hvdlocht]

@@patrykf4993 I ordered the exact solenoid from the AliExpress link provided in the comments at this video. And my printer is still working fine since the replacement.

[@hvdlocht]

@@favers77 My apologies, I did not get notification of your question and only just now see it. I hope you could fix your printer. It is the exact same part number, I ordered the exact solenoid from the AliExpress link provided in the comments at this video.

[@GrahamHaughton]

I followed your video as had the same problem with a C410W. Now when I power on the rollers don't move on start up and I get a red error light. Any ideas what I've done incorrectly. Any help gratefully received. Graham

[@heshamalkhazmi5038]

Thank you very much ... since I do not have a new replacement solenoid in hand .... I put a piece of barcode sticker firmly on the rubber of the contacting solenoid (I wish I took a picture) and cleaned any sticky traces and now it is working perfectly .. I hope it doesn't fall off soon - LOL !!! Thank you so very much for this fantastic detailed video ... without it i would have never been able to locate the solenoid - I hope you can take another video of how to install the switch "Closer view" in the proper position (it took me a very long time getting it back in place) - i recommend opening the other cover and remove the power board (5 screws + pushing the clip in the middle) - Again ... Excellent video ... my respects ....

[@PaoloMarcelli]

Hi! Do you mean the switch that senses if the back cover is open or closed? Sorry for that! You can buy a solenoid in advance from here kzbin.info/www/bejne/Y5Snnnlpg6t6q8k just in case it will fail, in any case, thanks for watching :)

[@alejandropalestina8193]

Thank you for such an excellent video, I also have the same fault, it does not pull the paper and my query is how I ask for the part to buy it, thank you

[@LMTHZ]

A miracle, once again. Thx for your video.

[@PaoloMarcelli]

Thank you for watching :)

[@hannavandenbulcke2801]

Hello Paolo! I have a Samsung Xpress C1810w having a similar pick-up paper issue. Would the inside of the c1810w printer be similar to the printer in this video? Meaning I could follow your instructions above and apply to my printer? Also, if so, could I purchase the same solenoid mechanism from the link, or does it need to be a different one? Thank you in advance for your time!

[@pseast]

worked to fix xpress c460w. Though, I didn't replace the solenoid and just replaced the foam pad as suggested in another video that points here. Thanks!

[@simonlam8834]

保罗，感谢您的精彩教程！你令到我的 C460FW 只花了10欧罗便活过來了!

[@pensierolibero_73]

Thanks the king of clp 365

[@alfx4356]

complimenti per il video! poi ci spiegherai come hai fatto a rimettere tutte le viti al loro posto :) sei veramente bravo!

[@adamjab1]

Thank you Paolo! Great guide, I saved a lot thanks to you!

[@sjakob52]

Hi Paulo. The tip of the paper is graped by the pick up roller and the printer stop emmidiatly with yellow blink. I can pull the paper out with easy draw. Do you think this is a solenoid problem or something else?

[@alessandrobrazil3886]

Hi Paolo, I need the FIRMWARE CLP-365W , Do you have this???

[@farrukhleghari8078]

Thanks mate. A hectic job that worked out well for me.

[@francknourd5624]

Detailed and easy to understand.... thanks... please can you send a link for buying the pad...I can't find it 😉👍

[@PaoloMarcelli]

Hi! The pad or the solenoid? I don't think they sell only the pad, however you can try to replace the pad with some kind of thick adhesive tape if you want to save the solenoid :)

[@davidbevan2439]

Thanks very Much for this. you have just sorted my printer for me. i dismantled cleaned and resistance checked solenoid. mine was stuck. I guessed at that point nothing to lose if i reassemble hey presto works.... Thanks...

[@lucjanszoanski1374]

Than YOU so much!!!! You save my printer !!🎉🎉😅🎉🎉

[@monclee]

Thank you for this great video, i fix the printer but now is printing not aligned. What should i check to correct alignment?

[@PaoloMarcelli]

Aligned? You mean the single colors are not alligned with each other?

[@monclee]

@@PaoloMarcelli thanks for replay!!!... no... the hole print into the sheet, somehow i fix the paper feed but image is not aligned with the sheet now XD.

[@Edmax52]

Grazie.. Ho sistemato la mia senza sostituire il solenoide, forse troppo debole, aggiungendo uno spessore..ottima guida. Sei un grande.. Grazie

[@ykejaarsma9876]

Thank you. Now my printer works fine again. Yke Jaarsma Netherlands.