Paraffin Wax Autoignition

This video is a more detailed breakdown of a demonstration I showed in a previous KZbin Short, where a boiling sample of wax will burst into a fireball when placed in an ice bath. This demonstration is a good example of how environmental conditions affect a reaction. Even though the boiling hot wax is well above its autoignition temperature of 245 C, it won't autoignite until a vapor cloud is produced with the right amount of thermal energy, wax fuel, and oxygen gas present.

[@johnford7847]

I've got a Ph.D. in chemistry, taught college for 35 years, had never seen such a thing, and think this is a delightful video! Wish I'd had it while I was still teaching. Good job!

[@Chemteacherphil]

Thank you!

[@vadimc2144]

35 years is quite a number, sir. Thank you for your service.

[@BackYardScience2000]

To still be as delightful as you are after 35 years of teaching, especially teaching college, you must have a heart of gold. As others have said, thank you for your service to our education system and for teaching our next group of chemists.

[@blue5659]

It is difficult to get a PhD in anything takes a lot of effort. But then chemistry is superstition at best. Why can tetracyanoethylene accept an electron but not tertraaldoethylene? Why does anti/aromaticity exist, when all atoms on the ring have a full octet either way?, why is benzene stable, borazine as well, but not hexa aza benzene, n6? Being unable to answer freethought guestions is the hallmark of nonscience

[@Daboresa]

Well sir what I can tell you I think what he just done here is forcing to cool down the flammable liquid which has reach it's flash point, even in deep fryings once the cooking oil reach its flash point any attempt of trying to cool it either by pouring water it can cause fire explosions, anything that reach it's flash point can be extremely dangerous

[@analog_guy]

Very impressive demo. For a fun and safer demo, light an ordinary paraffin wax candle. Once it has burned for a bit, snuff it out. Wait a few seconds until a nice stream of "smoke" (actually vaporized and condensing wax) forms, rising upward. Light the top of the stream with a lighted match. The stream will ignite, and the fire will run down the stream and re-ignite the candle.

[@Gothmogdabalrog]

I used to do that as a teen but didn't know that this is the scientific explanation for it. Thanks for that.

[@i-love-comountains3850]

That explains why it works with a paraffin wax candle and not a stick of incense or so

[@MrMuz99]

I've known this a while, but I could never have explained it like you did. Thank you!

[@RedFail1-1]

That is not the same concept that is happening here... The reason the candle wick reignites is because the smoke is hot enough and has enough flammable particles in it to be reignited by a flame you introduce. This wax ignites itself, which is already entirely different from your demonstration, for an entirely different reason. One you could have read in the description and realized they are not the same reaction and saved yourself the trouble of this comment. Two entirely different things.

[@jimshort9266]

@@RedFail1-1… wax vapor, oxygen, and heat in the right concentration. Sounds similar enough to me.

[@nickcaruso]

my parents used to seal preserved fruit with wax and i remember them warning me about wax vapors. mom melted the wax bars in a double boiler to keep the temperature at or below boiling water temp, and took it off the stove immediately upon melting to seal the jars of preserve. fascinating to see what they were worried about.

[@charleshines2142]

I never knew wax could do that. Sometimes you learn something new.

[@LindaKing-lf8nk]

That is what my mom Did too

[@FeigningAloof]

We did this in high school in 2003 by accident. My teacher asked to see it again, then told us to never do it again. We didn’t understand what had happened, but we were simply igniting it without the ice. The fireball was impressive. Left a black ring on the ceiling. We all still have and still had our eyebrows…

[@peterk.4266]

lol

[@lennartjuhh]

Cool teacher

[@GermanSausagesAreTheWurst]

That's a good example of why wearing PPE is so important, even if it seems like it isn't necessary. You never know what might happen.

[@drmanojpb]

This is an excellent video to show why paraffin oil shouldn't be used as a heating media in a oil bath while setting up a high temperature reaction !

[@oliveraguirre8172]

This explains the accidents that occur or have occurred in candle factories or accidents at home making decorative candles, which have resulted in children with third degree burns. Thanks for most.

[@beeble2003]

Not really. I very much doubt that anyone making candles is boiling the wax or heating it much beyond its melting point. Accidents are much more likely to be simply because the wax is flammable and close to a flame.

[@oldmech619]

As a kid, I wanted to experiment. Yes, I boiled wax just to see it boil. Why? Because I could. I am totally amazed that I am alive today.

[@oliveraguirre8172]

@@oldmech619 you are my fucking hero

[@robertschmit7837]

No water is necessary. Just tossing molten paraffin into a sink or a pail disperses and oxygenates it enough to autoignite. I did it in high school myself.

[@daphnefernandez6589]

This experiment can also be done by heating the paraffin wax and then throwing the hot wax from a height (1.5 metres). It will ignite when it reacts with air. We called it "Greek fire". The students just loved it! We still have a black ceiling, it is so cool! I do enjoy your videos, I love your enthusiasm. It is infectious!😢

[@zygmuntthecacaokakistocrat6589]

Immersive waxing of bike chains (at ~ 200ºF/92ºC) is becoming more popular, because it is better than mineral oil, but some holdouts are citing paraffin's supposedly super-flammable properties to argue against. it. I'm glad that this video exists, so that I can point to it to prove that you have to boil it & then super-cool it to make it auto-ignite, and that doing so in a slow cooker or double-boiler is nigh-on impossible. Thankyou Phil.

[@doomsdayrabbit4398]

Boil it and supercool it in a container that doesn't respond to thermal shock except by shattering.

[@bwhog]

That still doesn't absolve them of having to deal with the problem of wax vapors. Auto-ignition may not be possible, but thermal ignition still is.

[@Kyle-sr6jm]

I have been waxing chains for decades. It melts at just over 100°. No reason at all to take it anywhere near boiling point.

[@d.jensen5153]

People worry about the damnedest things!

[@CoxTH]

I remember my chemistry teacher in high school loved showing this off. Always been a favourite of mine.

[@PaulG.x]

That's a good visual representation of stoichometry in action. Ignition occurs first at the point where the air/fuel mixture is optimum

[@Smedley1947]

How do you measure stoicism? It's pretty subjective. Just kidding I'm just another wise ass with a degree in chemistry AND English. Not a lot of crossover in those two fields but it did help writing papers.

[@gus473]

That slow-mo close-up was excellent! Quite a video! 😎✌️

[@ALiz86]

I have heard of people using paraffin to heat homes, to cook and even power a refrigerator (typically you see them most often in 3rd world countries). I have also seen that the paraffin can cause fires and severe burns to people. This illustrated why it happens. Thank you!

[@fitzroyfastnet]

That's a different substance. In most parts of the world "paraffin" means kerosene.

[@PaulG.x]

The modern world uses that paraffin to fuel their flying machines

[@ALiz86]

@@fitzroyfastnet Wow. Those are very different! TY

[@JaSon-wc4pn]

I still use the old school whale blubber for heating my home Highly recommend

[@rich1051414]

Paraffin wax is a wax made by a reaction that includes paraffin, the main component of kerosene. The wax isn't kerosene anymore and kerosene isn't the wax. AFAIK, any wax would behave the same way as in this video, but I am not going to test that. I just don't see why it wouldn't.

[@somethingsomeonesaid6455]

At almost 45 years of age, I might have to take a chemistry course, thanks to your short videos.

[@somsackvongsa7077]

I m sixty.i take youtube chemistry .never to old for knowledge

[@bwhog]

I used to be fascinated by chemistry but realized quickly that I didn't have what it took to master it. Still, I'd be pleased to relearn it.

[@Smedley1947]

Depending upon how deep you go into chemistry, it's not that hard until you need math. If you have no problem with math then almost any field in The Sciences can be understood at least at the lower levels.

[@lisaharmon5619]

I used to make candles. Thank you for showing just how dangerous paraffin can be.

[@matthewmicallef3811]

This can happen with many other types of waxes and natural waxes. It is not because paraffin is dangerous that this occurs, it's because of the physical properties of wax and how it behaves at various temperatures. This model could easily be replicated with something like soy wax, or coconut wax because they too are made of hydrocarbon chains.

[@lisaharmon5619]

ALL candle waxes are classified as solid fuels.

[@napalmholocaust9093]

The arson investigation over my gramma's house burning down around her concluded that she did this while making candles in jars to cool them faster and caught the drapes over the sink, then flames went behind the cabinets catching the foam insulation.

[@ickipoo]

Wow. Yikes. Poor grandma.

[@bledlbledlbledl]

tried that several times years ago with a metal can. heated it to boiling, poured in a small amount of water (using a spoon tied to the end of a stick), and watched it go FOOM.

[@bigjay875]

Excellent demonstration, never herd this trick till now 👍

[@IvanIvanov-ug5dc]

Beautiful, I mean the explanation as well as the process itself.

[@Raptorman0909]

Wax has a very high specific heat capacity of about 2.5 J/gK -- not quite the value of water which is extremally high at nearly twice that of wax but way higher than steel or copper or aluminum. So, when the wax was heated to boiling the heat contained in the wax was enough to instantly vaporize enough water to cause the wax to jet upwards and increase the surface area exposed to oxygen. The energy content of wax is also quite high -- about the same as many fuels we use.

[@thatprogramer]

Very good explanation, I used to always be confused by this!

[@Galileosays]

Great safety video to demonstrate a form of a BLEVE (boiling liquid expansion vapor explosion). In reality these catastrophic events happen when a superheated tank ruptures. Here the sudden formation of a heterogeneous azeotrope causes a quick vapor expansion.

[@jobloggs6528]

Bleve

[@BackYardScience2000]

You can also take a burning splint and touch the tip of the test tube once it starts fogging over with fumes and it'll ignite the fumes inside the tube and cause a fairly loud explosion within the tube. Don't ask me how I know this...

[@JaSon-wc4pn]

Love the Channel. Psssst. Fbi are on their way

[@seansingh4421]

Dude has a pretty sweet fume hood. I’m jealous, the one I had wasn’t this cool

[@DANGJOS]

Ah you've finally explained it! So many people were speculating so many wild different things in the original video. Most of them made little sense to me. I don't remember exactly how I arrived at the right answer. I think I saw another video of someone explaining that the glass cracks and rushes in. It's also possible that one of the many explanations from people mentioned it.

[@GillAndBurtTheCop]

This is the most incredible video I've seen in a while. My eyes went wide as saucers seeing the short, and I had to look up an explanation which led me directly to your main video haha!

[@GillAndBurtTheCop]

I learned so much in such little time, I understood your explanations but was already questioning everything you eventually answered with my background in such fields of science.

[@thechannel8x]

I love these *to the point* videos, I wish YT was more like this ❤❤❤

[@charlesurrea1451]

I used to take scrap wax and fill a coffee can. The coffee can would sit in the middle of a bonfire. Eventually the vapor would ignite above the fire itself. If you were to spit in it, it would eject a ginormous column of Fire!

[@stevenwilgus8982]

I've never seen such before. And yes, it raised my awareness of what NOT to mess around doing....

[@thececil021]

I use paraffin wax at work. Thankfully, we’re not getting it more than about 100 degrees Celsius, usually no more than 85-90. Past 100, you start to smell it. I guess the boiling water mixing with it at that point starts to do weird things with it. Makes sense now.

[@paradiselost9946]

"a coil, well insulated by leaving in a pot of hot paraffin until all bubbling has ceased... boiling of the wax shall render it useless and one must start afresh..." god i have some weird quotes.

[@mobuildsstuff]

@@paradiselost9946 Sounds like some early inductor insulation tutorial, any idea where this is from?

[@paradiselost9946]

@@mobuildsstuff it will be one of teslas articles i believe. "some experiments with high frequency high potential currents", possibly? though it might be any of the old induction coil books, actually...

[@mikelamonica3681]

Thanks for this video. Many years ago I burned wrist badly by accidentally doing this. I had no idea why it happened until now.

[@maxasaurus3008]

Guy sets up a fairly dangerous seeming demonstration for us featuring fire and reactions and thanks US! Bravo Mr. Scientist, I know paraffin is a monster to tidy up so: Thank You 🙏🏻!

[@dtbsgaming5031]

I remember covering a paper in wax and rolling it and setting it to fire. It sort of exploded and wax spread around it. I never understood how that happened but after seeing your video i think it was the same phenomenon. Thanks 🙏👍

[@sanches2]

This was soooo imteresting thanks for showimg and explaining in such good way! As soon as you showednthe slow motion i started to figure out whay it is igniting but it is always best to have someone who knows toexplain the extra bit:) Thank you. Subscribing for sure!

[@PaulLouis-jt9pz]

I did this on small scale when i was 13, i was very cool, and it never left my mind

[@FiXato]

more of this long-form content please!

[@jamesquinn3414]

Thanks! Knowledge saves lives!

[@jonfranklin9361]

Wow! That was awesome! Culver is a nice school. Love going out on lake.

[@davegoldspink5354]

Going to school in the 60s and 70s as much as I loved science having a learning disability I always sucked at understanding it. Watching videos on the subject I always wish we had the technology back then we have nowadays.

[@calbrock6302]

Subbed because you’re awesome

[@matthewmicallef3811]

I never knew that wax could so easily combust due to temperature changes. Does the ignition occur because the vapourised wax used the vapourised water molecules, or would this occur had there not been a rapid change in temperature due to the ice bath? Would it work similarly if for instance the water bath was filled with hot water instead?

[@shawnkiesel5349]

What happens if you pour the boiling paraffin straight into the ice water ? Would it do the same, but maybe on a smaller scale.?

[@bullang3r95]

You should definitely invite the Slow Mo Guys to your lab, I'm sure you can make awesome videos together!

[@JEWCIFERSHEKELSTEALER]

Youve been most helpful. 😊

[@jsl151850b]

Is the Bunsen Burner....which is *RIGHT THERE* igniting vapors?

[@Jim-fe2xz]

As kids in 1962 we used paraffin to wax our surfboards. We learned it lasted longer if we would melt it in an old tin can then brush it on our boards. Our parents told us to be careful not to get it near water while we were doing this but never told us why. Now much later, I finally know! (We never got it hot enough to boil - just enough to stay melted while we applied it to our boards). In high school chemistry we learned about state change and a drop in temperature as paraffin is heated to melting but nothing about autoignition - probably a good thing at that age LOL!

[@lhpl]

This might be a good place to tell my little story. It was a cold winter, and the central heating was broken and could not be fixed for a few days. I was feeling cold as hell, and needed to get the room temp up, so I placed seven tea-lights on a small porcelain plate and lit them. It did work fine, giving some very welcome warmth. I had of course ensured that nothing flammable was nearby or above. After some time, all the wax had melted, which isn't unusual with tea lights, however the heat was enough to make the wax boil, and of course the gas ignited immediately with a giant flame, and now the tea lights were continuing to burn as one huge surface of fire, like a pan on a stove with burning oil. I quickly found a metal lid or pot or whatever and placed it over the plate with the tea lights, which killed the fire, but when I removed the lid, it would immediately reignite, until I left it to cool down. No harm done. But it sure was a learning experience. Even tiny tea lights can pose a serious danger! Don't place multiple tea lights close to each other. (I can't recommend repeating this experiment, but if you ignire my advice, at least do it in a safe location, keep the tea candles in a pan for which you have a tight fitting metal lid. The lid will get very hot, so use good insulating oven gloves.)

[@FarmerDrew]

Use a clay pot over the tea candles. The clay is a great radiant heater. The hole in the pot chimneys the gas out.

[@Tadesan]

Holy crap that's awesome!! A two sided fume hood!

[@lamenwatch1877]

You remind me of my own highschool chemistry teacher, Mr. Topping. He would do really cool demonstrations for the class.

[@gottagift]

always did wonder about rags soaked in linseed oil needing to be discarded in a self sealing container.

[@johyw2267]

After the melted paraffin, what can I use to keep it melted inside a closed bottle?

[@eb1138]

Oh man. I have to try that!!!

[@BlackSoap361]

In one of the clips, it looked like the test tube didn’t break, but the fireball still happened?

[@jamesraymond1158]

Great video. Here's an idea for a future video: explain why gunpowder needs a little sulfur to work.

[@alexstone691]

Would it self ignite if you just poured the contents without any ice?

[@calbrock6302]

Whoa!!! Is why some skin cream (cetraben comes to mind) have warnings on to keep away from naked flames??

[@alsmith20000]

So to be clear, this won't happen if the test tube stays in tact? it sounds like it is pretty much the same thing as what happens if you try to put out a cooking oil fire by putting water on it.

[@boxsterman77]

Can wax be considered compressed (à la Diesel) to ignite.

[@pirobot668beta]

We did a similar trick, but dropped hot wax drip-wise into a pan of cold water. It didn't always flare up, but when it did it was dramatic!

[@markrix]

Wait whhaaaa?? Does it work with all types of candle wax because they vary. Also you sacrificed a test tube, would this also work if you poured the wax into a cylinder half filled with cold water??

[@gkiferonhs]

Great illustration of flash point, too? It appears that the part that initially ignites is a darker gray than than the bulk of the vapor cloud. Does ignition always occur within the dark areas? Could that be sayinig something about droplet size?

[@WestOfEarth]

My grandma used paraffin wax when plucking poultry to remove the fine hairs on the skin. Melted over the bird, cooled, then peeled. I remember those packaging boxes too. If I had known this back then, I think I might have advised against using it, lol.

[@gijsv8419]

Did water get in touch with the parafine ?

[@rileyh212]

So, is it because it’s petroleum based, or would beeswax also combust?

[@NorseForse]

I’m more impressed by that fancy yard stick with the claw on the end affixed with painters tape!😂😂😂 Ahhhh… science!🧪

[@WiscomptonBoys]

This my favorite thing to do back in the day.. we’d get a whole little metal bucket of wax in a campfire melted to the point it was “on fire” where the surface looked like it was burning.. then we had a bucket of water taped to a rake we would dump onto it and get a fireball 10’ high! We called them “wax bombs”.. really takes me back.

[@rhofour]

So how come we don't see the wax vapors igniting while you're heating the test tube? I'd think as soon as they leave the top of the test tube there should be sufficient oxygen to burn.

[@jackshaftoe1715]

Let grade school boys watch this, and in 10 years we will have the best chemists in the world.😊

[@ijustwannaleaveacommentony6511]

that is bonkers! how come it didn't ignite over the open flame when being heated to boiling?

[@BBQDad463]

Thank you for this video. Totally far out! Does beeswax do the same thing?

[@k.chriscaldwell4141]

Good info. Thanks.

[@piran_dler]

Want to hear a Potassium joke? K!

[@beeble2003]

Na, I prefer sodium jokes.

[@LFTRnow]

NaBrO - Sodium hypobromite jokes are the best.

[@brotherfiretribe9566]

Same occurs with sugar dust in refineries

[@ThomasD66]

Not exactly the same, those types of events still require some sort of ignition source, usually from an electrical system, but sometimes just static discharge.

[@Smedley1947]

Not at all the same phenomenon. Sugar and wheat flour factory explosion are simply the ignition of ultrafine dust suspended in the air. There's no critical temperature like the flashpoint of the paraffin, it is merely the result of fine dust in the air, surrounded by plenty of oxygen plus an ignition source. One of the horrifying things about some of those Factory explosions is that the first explosion might be in a side room but the Shockwave dislodges dust from the rafters and beams Etc in other rooms and eventually ignite from the first blast which usually starts a fire, so there can be a chain reaction throughout many rooms and areas of the factory all starting from one spot where the proper mixture met an ignition source, be it static electricity or something like a pilot light.

[@user-ez6zi2rc7t]

Just tested this. Awesome.

[@lightdark00]

I'm going to try this!

[@scotts.2624]

I wonder if this is causing some of those candles in jars deflagrating?

[@robertschmit7837]

Paraffin is used in home canning jam/jelly which I now realize is very dangerous. I once created a fireball by just tossing the molten wax into a sink in the chem lab. Saves some steps

[@russcrawford3310]

I've been using a metal container all this time, that was my mistake ... next time I'll use a glass jar ... Why doesn't the wax vapor ignite evolving out of the test tube? ... does the vapor now deposit in the flue? ... I keep a fire above my boiling wax, just to keep account of the stuff ...

[@holgerackermann7991]

One of the experiments I like to show too. There is another experiment where you can show that heating paraffin-oil at boiling point for some time generates gaseous and liquid cracking products (alkens). So I guess this and the intermediate formation of radicals might play a role in this self inflammation(?)

[@michaelshortridge6379]

I've worked in oil and gas industry. Raw parrifin is clear black. Really flammble.

[@dougclem7711]

The flame of a candle is burning the volitals accumulated at the top of the wick. Did you do a flash point with the Cleveland Open or Closed cup?

[@flyoverkid55]

I have one question. Who intentionally boils paraffin wax?

[@healthymindhealthybody9692]

Is paraffin wax safe on car paint/ clear coat . Does it have the clingyness of wax to paint. Also, does it haze up like wax on car paint ? Thanks

[@ariannasv22]

Thats cool, but the sound it makes up close at the very end just sounds so funny to me

[@d.jensen5153]

Very nice!

[@wonderstruckwow]

Great video. I've seen this reaction before where the boiling tube stays intact and you get the same effect. To be honest, I didn't realise that the boiling point was above it's auto ignition temperature and I had assumed that the ignition must be something to do with latent heat as the liquid wax droplets start to solidify but that didn't seem particularly realistic. Your explanation here certainly makes more sense but what causes the wax to eject itself so vigorously from the tube on initial contact with the iced water in the case where the tube stays intact (I just checked and the video I mentioned was actually your KZbin short from back in October last year)?

[@lqr824]

> something to do with latent heat as the liquid wax droplets start to solidify but that didn't seem particularly realistic. Your explanation here certainly makes more sense but what causes the wax to eject itself so vigorously from the tube on initial contact with the iced water The tube BREAKS. That lets water contact the 370C paraffin, which turns some of the water almost instantly into steam, which expands in volume 100s of times in basically an explosion, which ejects the paraffin and blows it apart into in effect an aerosol or similar, with massive surface area with which to react with oxygen.

[@iteragami5078]

@@lqr824 in the video, the first time he plunged the tube, it seemed to be unscathed after taking it out? (liquid wasn't leaking profusely out of tube). Or was the crack too small to have any effect?

[@Chemteacherphil]

Every time I’ve done this demo, the test tube has cracked. In some attempts, the cracks were smaller such that residual solidified wax held the tube together.

[@wonderstruckwow]

@@Chemteacherphil Ah, right. I did post a reply to @lqr824's comment with a link to your original short where the tube does appear to be intact - but I guess KZbin deleted it because of the link. So this is really a self-igniting variation on the old 'chip pan fire' demo. Great video and love the channel!

[@docteurlowbat]

@@Chemteacherphil Maybe a kind of Venturi effect ?

[@markiangooley]

“But the glass will crack!” “Yes, that makes it all happen!”

[@TheClonetruper]

Is this at all similar to pouring water on on a foaming pan or putting ice in a hot fryer?

[@Mr.Kalamar]

The reaction is impressive and scary at the same time ! Also, I was wondering, why are there what seems to be two gaseous phases (a more cloudy one on the upper part of the tube and a coloress one between the cloudy one and the melting paraffin) at 1:04? Are they the different substances from the paraffin with a different melting point and density ?

[@coryman125]

If I had to guess, the clear lower part is hot enough that the wax stays as a vapour, but higher up the glass is cooler and so the wax can condense on it? Kinda like how there's usually a gap between boiling water and the visible steam

[@Mr.Kalamar]

@@coryman125 Sounds right yeah, it could be it but the fact that the two layers are separate makes me think of a other byproduct formed or something like that

[@vineetsrivastava5515]

I believe that this is more of a physics question than a chemistry question but yeah I guess the explanation above is correct.

[@MadScientist267]

The "cloud" is vaporized wax that hasn't reached oxygen yet to react. You can see this happening in a normal candle flame as well. Edit: Oops, misread the question, but the above is still true as well. Yes the clear zone is similar to what water does at higher temps or lower concentrations, it is clear. The cloud forms as wax starts to condense as it cools a little leaving the bulk material. Then when it leaves the tube, it spontaneously reacts with the oxygen in the air.

[@HansLemurson]

Why did the vapors coming out of the test tube when you were boiling the paraffin not ignite when you were heating it?

[@ThomasD66]

Remember that it is the vapor that ignites, not the liquid, and at the surface of that boiling liquid, there just isn't enough oxygen to support the reaction. Especially so in the restricted space of a tall test tube. It's much the same reason you can throw a lit match into liquid gasoline and (sometimes) it will not ignite.

[@andrewbrown6522]

I had a candle explode in a cabin a few years back. I thought the tin can i was using as a candle holder somehow turned into a spring via some kind of bi-metal reaction but now i wonder if the wax wasnt slowly boiling away until it got some cold snow through the window. I was sleeping and only saw the immediate aftermath but it was clear that wax had sprayed.

[@metallicamadsam]

If you use a small amount of wax, like really small, will it auto ignite upon boiling due to surface area and available oxygen?

[@metallicamadsam]

My follow up from that question, would be can you calculate that and make a video? 😊

[@Shadow27374]

Interesting, as a kid I used to play around with tea lights and burn gummy bears and chips etc in them. Suddenly there was a ~2m jet flame that was even really loud. Now I know what must have happened. Has really sprayed the flame at that time.

[@perfectomprg]

I instantly wanted to try this at home

[@donaldasayers]

Funnily enough I have done this, My dad worked in wax for a big oil company so there was always blocks of wax about at home.

[@bobanmilisavljevic7857]

Did you ever wax some curbs to skate?

[@velfaern1716]

I love the “let me show you what I mean” and then just an incendiary goes off

[@ThomasD66]

That is a bleve. Boiling liquid expanding vapor explosion. You don't even need an ice bath. Quickly toss/drop some boiling paraffin from a height on a cold day and you can create the same fireball. That boiling liquid is already well passed ignition temperature, so all you need is proper dispersion of the vapor in air. Best to do this over ground that is either non flammable or covered in snow.

[@ketsuekikumori9145]

Before I watch the rest of the video, this is my hypothesis: By melting it than plunging it into ice cold water, you force the wax to condense into fine particles. That sudden condesation causes a vacuum which forces air to rush in and stir and throw up the fine particulate. With the high suface area and oxygen rich atmosphere outside the tube, it ignites. Will edit if I'm right or wrong. Edit: Partially wrong. Rather than an inrush of air, it was the tube breaking and an inrush of water that caused the wax to vaporize and ignite.

[@ajingolk7716]

Hi Jhon can you help me dissolving zirconia please i tried sulfuric acid at 100 C°

[@DysnomiaATX]

If the testtube did not crack, meaning the wax is not sent into the air, would we still see a smaller reaction as just the vapor inside the testtube mixed with the cooling wax or would the liquid wax just solidify as the testtube cools?

[@PaulG.x]

It would just cool and solidify. The large expulsion of vapour which was above the auto-ignition temperature of paraffin was the reason it ignited.

[@WallaceRoseVincent]

What type of wax is used in lava lamps? Most if not all waxes I've tried to use float in water but lava lamp wax sinks in water. How is lava lamp wax modified to sink? The Internet says they used to mix the wax with carbon tetracloride. Is that true?

[@kentek3141]

Phil, just wondering on history of your lab coat with Culver Military Academy logo. ken class or '59