Very good presentation. The Lord has a sense of technique.
@darijan-diy4 жыл бұрын
Thank you
@hogarnemilosrdni25854 жыл бұрын
Great job man. So many details. I was enjoying every minute. Thank you.
@darijan-diy4 жыл бұрын
Thank you
@darijan-diy3 жыл бұрын
@Mihai Alexandru Cazacu Crimson Fly - Huma Huma
@judithrob15914 жыл бұрын
Very important if you would like to saw with precision. Always choose a Miter saw with a handle positioned in a vertical line above the saw blade. Everything must be aligned, slide rails, handle, and saw blade, it is much better this way the blade will not tilt. Because there is some torsion in the aluminum housing . And choose an engine with softstart on it to prevent wear of the gear and worm shaft. It is very important that everything is aligned. Here are some examples to show how the handle must be positioned above the blade. Bosch gcm 800 sj / Bosch gcm 8 sjl / Evolution rage 3 / FESTOOL KS 60 / / HITACHI C12RSH2 / FESTOOL KS 60 E KAPEX / Metabo KGSV 72 Xact . (This also is the case with the Miter saw without the slide rails). If you want you can test it yourself at home if there is torsion in the aluminum housing. Step-1. First you make a saw cut from +-5 mm deep in to a flat piece of wood. To this with the normal handle postioned on the right side of the Miter saw. Step-2. Then repeat this by pushing the saw blade down with your hand (finger) on the aluminum protective cover were the saw blad is cased in. Just now only do this without the running engine. Step-3. Now you can see if the saw blade will be positioned in or next to the saw cut.If the saw blade is (+- 0,2 / 0,5 mm) next to the saw cut then there is torsion in the aluminum housing. Step-4. therefor it is much better to choose a Miter saw with the handle positioned vertical in line above the saw blad. Step-5. When you measure the vertical 90 degrees angle square (Digital Angle Gaug) of you're sawblade don't forget that there is always some torsion in the aluminum housing. Conclusion:how further away the handle is from the saw blade how more chance of torsion in the aluminum housing don't go for that (the choices are yours). Also with a cheap slide miter saw it is still better the handgriff in line a above the saw blade than on the right side. Maybe they will make it someday then we have a winner...
@lazycarper79254 жыл бұрын
are there any good budget saws?
@judithrob15914 жыл бұрын
Also with a good budget saw it is still better the handgriff in line a above the saw blade than on the right side. Maybe they will make it someday then we have a winner...
@Ana-eg7ir4 жыл бұрын
Como se regula el laser. Lo has averiguado?. Danos tu opinion sobre si merece la pena comprarla. El precio si q es bueno, pero y la calidad?
@darijan-diy4 жыл бұрын
I'm satisfied with the saw. I do not use a laser for a clean cut
@diymaster2402 Жыл бұрын
🔝🔝🔝
@darijan-diy Жыл бұрын
😀👍
@TeoPriceputul3 жыл бұрын
still have it?
@darijan-diy3 жыл бұрын
Yes
@TeoPriceputul3 жыл бұрын
Do you use it often? Any problems ?
@darijan-diy3 жыл бұрын
Not very often. So far there are no problems
@TeoPriceputul3 жыл бұрын
@@darijan-diy Thanks. I have the 1500 version and I consider to upgrade and wanted to know your opinion.
@miosz90073 жыл бұрын
@@TeoPriceputul I had both. The MPKZ 2000 is a very noticeable upgrade over the PKZS 1500, it is just better in every way. My 1500 is gone, the 2000 stays. The motor is better, the blade is better and has a better size, handling is better. I think it is worth the upgrade. All this is minding the price of course, it is not a pro tool, but is really good for the hobbyist.
@ionutps4 жыл бұрын
Can cut iron/steel with the right blade or how you call it in english the grinder blade
@miosz90073 жыл бұрын
you can even use the stock blade. It really is not bad. But yes, this saw can cut iron as well as steel and aluminium and all the other good stuff no problem. Use some lubricant though, cutting oil or at least silicone spray or something, never cut metals dry.
@ionutps3 жыл бұрын
@@miosz9007 Thank you very much for your response
@miosz90073 жыл бұрын
@@ionutps you are very welcome. I own this saw and have cut 3mm profile steel with it. No problems so far. Yes, this is not a pro tool, but as a non-pro I am quite happy with it.
@baschticz4 жыл бұрын
Wo bekomme ich diese Parkside MPKZ 2000 A1 - IAN 315340 her !??????
@darijan-diy4 жыл бұрын
Lidl
@baschticz4 жыл бұрын
@@darijan-diy nein leider nicht 👻 ich suche seit TAGEN nach dieser Maschine 👻😡😡😡😡
@waldemardinius28564 жыл бұрын
@@baschticz lidl online shop
@Eike78894 жыл бұрын
Aktuell wieder bei Lidl
@evangallagher43874 жыл бұрын
Ciao, a me la moa taglia molto storto, hai qualche consiglio da darmi? Il taglio non è mai dritto
@ganakil4 жыл бұрын
dietro ci dovrebbero essere due bulloncini per la regolazione (svitando anche pomello grosso,mi sembra) della perpendicolarità della lama
@joaopicanco56124 жыл бұрын
Boa tarde como posso comprar um disco para essa máquina
@raymondnoirot27153 жыл бұрын
Super la tronconneuse mais toujours le même problème l'impossible de ce la procurer à quoi vous joué parksid à nous faire baver Noirot raymond de Ramonville saint
@Bigchurchmusic3 жыл бұрын
Excellent.
@darijan-diy3 жыл бұрын
Thank you 😀
@lijajausnik17595 жыл бұрын
zanimivo
@darijan-diy5 жыл бұрын
Hvala
@fubartotale33893 жыл бұрын
Seems kinda cheezy...
@CathyGiszewski-xe7py3 ай бұрын
On ne voit pas le deblocage de la scie .....🙄🙄🙄🙄🤢
@CathyGiszewski-xe7py3 ай бұрын
Ah j ai vu merci 😉😉😉🤣🤣🤣
@josephdarius6183 жыл бұрын
O
@ericmillois63313 жыл бұрын
il est pas très bavard le gars, il a du manger sa langue
@sylvaincouderc63224 жыл бұрын
M
@karenwright88712 жыл бұрын
Hate the music
@MrAleanor3 жыл бұрын
Chut!!! silence il n'y à rien à entendre rien de compréhensible. Simplifiez vous la vie lisez le mode d'emploi livré avec le materiel ,il est beaucoup parlant que ce pseudo démonstrateur à la ramasse qui plus est démuni de cordes vocales
@darijan-diy3 жыл бұрын
😃
@MrAndrjuha4 жыл бұрын
I better pay more for decent saw not this shit! Dont recomend even to beginers!