PART 2😎😎😎 Reflooring The Trailer

[@patkelly7999]

Mighty work Jason, PJ and Bow, trailer floor came out real well💯👌👍🙏😎

[@HollisFarmsMS]

Thanks

[@Frank-db6oj]

Looking good Jason. Thanks for sharing 👍

[@HollisFarmsMS]

Thanks

[@MichaelGilbert-cb5yq]

Love that skil saw Jason! The rougher the better!😂😂

[@HollisFarmsMS]

👍🏻

[@davidgolden3946]

Trailer looks good to make easier if you have to do another .Start on each side and put cut board in middle, remove holddowns on each end , and bolt down your boards, then holddowns last, no welding necessary. Burned motor oil and diesel make a great a great coating for trailer floor. Put you some magnetic led lights on rear for turn ,tail and brake lights. Great seeing Bo and P J

[@HollisFarmsMS]

Thanks

[@robertcampain612]

Great job!! I like your videos!! Thanks for posting!

[@HollisFarmsMS]

Thanks

[@mattyc195]

Great video and thanks for sharing.

[@HollisFarmsMS]

Thanks

[@mikehornsby599]

Got a lot done, trailer floor looks great , that cutter does a great job. Thank you for sharing check on you all tomorrow have a great day!!!

[@HollisFarmsMS]

Thanks

[@jacksanders7018]

A couple of coats of used oil will be great, thanks.

[@HollisFarmsMS]

👍🏻

[@willisdockery3972]

Good job on Traylor...those jack Russell are so cute

[@HollisFarmsMS]

Thanks

[@howardroy1097]

You are doing a fantastic job on the trailer

[@HollisFarmsMS]

Thanks

[@gregcothrum4045]

Great video Jason y'all have a great week and stay safe 👍

[@HollisFarmsMS]

Thanks

[@garywalton7176]

Looks dang good...give Cody a gallon of stain/sealer and film him staining it !

[@HollisFarmsMS]

Thanks

[@mikeprichard7933]

Hey Jason, your trailer turned out really nice but this advice comes from an old carpenter. You should have left a gap between those planks. 1/8 would be good 1/4 would have been better. That trailer is going to get wet and that deck will buckle up. I know you said you would store it indoors you will pick water up off the road and sooner or later it will get rained on.

[@HollisFarmsMS]

We’ll see

[@mitchtucker5768]

The rear angle iron by the ramp came from the factory with self tappers on both of my trailers. Easy to remove and replace boards. Drop your ramp and check yours. It may be bolt or screw in also.

[@HollisFarmsMS]

👍🏻

[@sharonlashley4392]

Looks good

[@HollisFarmsMS]

Thanks

[@gmass7238]

The flooring of the trailer turned out awesome. I agree those 2 are double trouble , but it's awesome seeing and watching those 2 on your channel.... They just put a smile on your face ...

[@HollisFarmsMS]

Thanks

[@stevenmarsh5158]

Another project done? The trailer looks good.

[@HollisFarmsMS]

Thanks

[@alanlashley943]

My biggest fear when bush hogging was being aware of the fawns laying and getting run over, instinct not to move is a demise for a lot of them. I know you know what to look for, but a lot of folks just plow on through, lots of babies lost from this every year, sad.

[@HollisFarmsMS]

👍🏻

[@kevincarver9949]

Awesome video thanks 👍👍👍. Hog blood stain will work good 😆

[@HollisFarmsMS]

Thanks 🤣

[@kennethrunyan3168]

Might try treating wood with linseed oil as the old timers use to do.

[@HollisFarmsMS]

👍🏻

[@calvinh.8882]

Looks good. As for welding it again, I own two that I bought new and they are not welded, they have 6 self-tappers holding that piece of angle iron on so that you can just unscrew it and replace the boards. I like it like that because once the boards dried out and shrunk they got lose and started bouncing and rattling more, so I tightened the screws up a little more and it tightened and held the boards down tighter so they don't bounce and rattle so much.

[@HollisFarmsMS]

Thanks 👍🏻

[@codyryan6866]

Put some diesel and oil on the wood last long time and do that every year or so last longer

[@HollisFarmsMS]

👍🏻

[@Dunlap-uj5zl]

👍

[@HollisFarmsMS]

👍🏻

[@thomashill7345]

Mix a little diesel with oil to help paint it on. Ck with your buddy cotton top about that.

[@HollisFarmsMS]

👍🏻

[@andrear596]

Looks like if you had flipped the last board over the straight edge would have been flush with the other board the cut edge would have been against the metal. But still looks really nice!!

[@HollisFarmsMS]

What difference does it make 🤷🏻

[@hugeblue]

8/21/23 - Good job on the trailer . That should last a long time ! Glad you finally got a weather brake so you can get back Logging! Have a good day!

[@HollisFarmsMS]

Thanks

[@billharris3335]

Trailer will haul whatever you need now!

[@HollisFarmsMS]

👍🏻

[@ericsmith7403]

If u put some water sealant on your wood it Will last you longer and be weather resistant. I know you probably already know this lol. Have a good day buddy

[@HollisFarmsMS]

Thanks

[@jasonlong3929]

I'm sure they treated boards

[@mitchtucker5768]

@@jasonlong3929 Even treated boards need some protection. I’m sure the rotten ones were treated when they were first put on. It’s best to wait about a year for some of the factory treatment to evaporate before applying Thompson’s etc. That way the board can soak up the new stuff.

[@greggrondin3034]

What them 2x10 run these days?

[@HollisFarmsMS]

Can’t remember