Part2b/2 How to make a 4s Li-Ion battery from 18650 cells, DIY tutorial.

  Рет қаралды 61,994

Maixe Chrys

Maixe Chrys

Күн бұрын

Пікірлер: 53
@MyOwnCrusade
@MyOwnCrusade Жыл бұрын
Your welder looks like a spider going through a tough break up. He is still at work getting it done, though, and i respect that. Hang in there, bro.
@arielelijah1282
@arielelijah1282 2 ай бұрын
How to connect to a 4s bms for DIY powerbank?
@Cephas2904
@Cephas2904 4 ай бұрын
This is a 4s2p config right? The diagram shows otherwise
@egtreadway4232
@egtreadway4232 10 ай бұрын
IM building this same battery pack for a rc plane, what gauge wire do you recommend , sorry cant tell watching video. thanks for any advice
@maixechrys6264
@maixechrys6264 10 ай бұрын
15:44 Rule of thumb will be 10% above the maximum amperage that the battery can deliver (its burst C rating). I believe that since rc planes dont consume much current you should be fine with 14awg or 12awg.
@egtreadway4232
@egtreadway4232 10 ай бұрын
Ok thanks, thats a big help my planes fly around pulling 6 to 10amp but on full throttle and during launch I see 30 to 35 amp draw
@mikehalvorsen4788
@mikehalvorsen4788 8 ай бұрын
Hey. Can you build your battery pack on a upward scale? Like 4 , then 4 on top and then another 4 on top etc.... let me know and how. Thanks 😎👍🇨🇦
@maixechrys6264
@maixechrys6264 8 ай бұрын
Hello thanks for stopping by, what is the required voltage (3s,4s or more)?
@mikehalvorsen4788
@mikehalvorsen4788 8 ай бұрын
What I'm trying to accomplish is making a homemade scooter and hiding the battery packs in a " dummy" frame. I want to have maybe three steel cylinders with the batteries incased and attached together. It will be a set of four on-top another four, upward. My question is how would you a joint the batteries going upwards?
@starlord8200
@starlord8200 2 жыл бұрын
Why you connect balance port without PCB?
@milesmoore5422
@milesmoore5422 2 жыл бұрын
So it does not matter where the BMS wires are located on the battery ?
@alfredbriffa1692
@alfredbriffa1692 Жыл бұрын
How is it you did not fix thermister or temperature sensor, please
@MyspiritMysoul
@MyspiritMysoul 2 жыл бұрын
Can you show how we can make a 14.8V pack of 4 cells (use only 4x18650 and set them on a series raw) using balancing connectors and have them tested in an Imax b6?
@maixechrys6264
@maixechrys6264 2 жыл бұрын
Απλα χρησιμοποιησε τις πρωτες τεσσερις μπαταριες και ενωσε τα θετικα του συνδεσμου ισολογισμου στα 4 θετικα των μπαταριων οπως απεικονιζονται στο 0:39.
@moturcu4226
@moturcu4226 4 жыл бұрын
Best battery videos on youtube! Thankyou
@maixechrys6264
@maixechrys6264 4 жыл бұрын
Glad to know it helped!
@garrettmcfarlane1901
@garrettmcfarlane1901 2 жыл бұрын
Well demonstrated and explained. I could follow every step.
@neilgahapon3310
@neilgahapon3310 3 жыл бұрын
What charger do we have to use? Is it okay to use Lipo balancer charger? Pls notice🙏
@maixechrys6264
@maixechrys6264 3 жыл бұрын
Well no the charger has to have a Li-Ion option, voltage ranges are not the same.. I mean it could be done but expect funny results in a few charges!
@neilgahapon3310
@neilgahapon3310 3 жыл бұрын
@@maixechrys6264 so what type of charger can I use?
@maixechrys6264
@maixechrys6264 3 жыл бұрын
@@neilgahapon3310 Any charger that specifically states it supports Li-Ion batteries. Whould you like a link.
@neilgahapon3310
@neilgahapon3310 3 жыл бұрын
Okay thank you
@gargolaconrad3188
@gargolaconrad3188 2 жыл бұрын
Wouldn't this be an 8s battery since you are using 8 - one cell batteries? I see other 4s Li-ion packs with only 4- one cell batteries.
@maixechrys6264
@maixechrys6264 2 жыл бұрын
They are connected differently(series/parallel) please watch part one to get a better understanding.
@gargolaconrad3188
@gargolaconrad3188 2 жыл бұрын
@@maixechrys6264 OH OK, I'll watch part one, thanks. I'm just learning about battery packs.
@maixechrys6264
@maixechrys6264 2 жыл бұрын
@@gargolaconrad3188 no wories mate my bad I hadn't put a link.
@missiletm
@missiletm 3 жыл бұрын
Great explanation. One tip for you, get some flux, it will make your solder flow much better requiring less heat and stronger bonds. A couple of your joints looke like cold joints which are a lot weaker. 👍
@maixechrys6264
@maixechrys6264 3 жыл бұрын
Always appreciate helpfull feedback for improvement, I ll give it a go thank you!
@chongshenchang9367
@chongshenchang9367 3 жыл бұрын
Sir, can we mix cells of different mAh in Lithium pack..??
@maixechrys6264
@maixechrys6264 3 жыл бұрын
No, it is not possible and it is very dangerous if you do so.
@chongshenchang9367
@chongshenchang9367 3 жыл бұрын
@@maixechrys6264 Ok. Thanks.
@maixechrys6264
@maixechrys6264 3 жыл бұрын
@@chongshenchang9367 thank you, please make sure you watch part 1 and 2 as they cover anything you need to get started.
@chongshenchang9367
@chongshenchang9367 3 жыл бұрын
@@maixechrys6264 Ok Sir..
@__-hh3gt
@__-hh3gt 3 жыл бұрын
Dramatically fantastic. Thanks
@omaralvarado1080
@omaralvarado1080 2 жыл бұрын
That is great, but it’s better if they are spaced out
@strawhat.eth.
@strawhat.eth. 4 жыл бұрын
Helo can somebody help me i have a question i have a ebike 240watt motor the standard battery is a 24v 10amp now i want new battery en i see 18650battery of 10 to 35 amps can the bike handle 35amp battery (i need a 7cells battery en wand to put in itch cell 6 battery that makes 3.7v itch cell en total of 24v 30amps)
@sphamandlas.madlala6530
@sphamandlas.madlala6530 4 жыл бұрын
It should be fine with a proper BMS, the motor will draw the current it requires from the battery i.e. 10amps at 24V. keep in mind that the motor will draw current to it maximum power which in your case is 240watts, what im implying is, as the pack voltage decreases the amount of current the motor draws will increase hence why you will need a proper BMS to protect the pack.
@maixechrys6264
@maixechrys6264 4 жыл бұрын
@@sphamandlas.madlala6530 Sorry for the late reply as long as the voltage is the same as the stock battery and the amp draw does not go beyond the capability of the battery (C rating) everything is fine. Hope you already figured out a solution by now, please share if your project worked!
@tonymontagnard1597
@tonymontagnard1597 4 жыл бұрын
14,15 volts total 3,7v x8 = 29,6 volts why only 14,15?
@maixechrys6264
@maixechrys6264 4 жыл бұрын
Hello thank you for your question. So assuming you are reffering to the thumbnail photo that is depicts a pair (2) of batteries connected in parallel, each pair consisting of 4x3.7 volt cells so a total of 8 seperate 18650 batteries for both packs. Each of the 4x18650 batteries (a single pack) are connected in series, the voltage is the sum of the batteries included in the pack (4x3,7v=14.8v) and the capacity is the same. (assuming the nominal voltage of each of the 18650 batteries to be 3.7v, unless you want the min 2.9v rating or max 4.20v) Vice versa for the parallel connection between the two packs that give no increase in voltage but doubles the capacity. I hope this clarifies the issue but if this is not what you meant please tell me what is the schematic you are reffering to in the timeline. Stay safe!
@maixechrys6264
@maixechrys6264 4 жыл бұрын
Also please make sure you have watched the previous videos in the series Part 1 kzbin.info/www/bejne/f3jdZmqIi7OhhsU Part 2a kzbin.info/www/bejne/Y5_TfYSDZ56HrJo
@bulldogpatje
@bulldogpatje 4 жыл бұрын
Very Very Good explenation
@steliostheofanou1368
@steliostheofanou1368 2 жыл бұрын
ωραιο βιντεο μπραβο αδερφε
@maixechrys6264
@maixechrys6264 2 жыл бұрын
Ευχαριστω πολυ!
@m3chanist
@m3chanist 2 жыл бұрын
Your schematic doesn't match the battery as built, luckily. It doesn't show the parallel connections of the middle two cells in each 4S section, only the outer two of each. If it was made according to your schematic those cells wouldn't be balance charged and would end up as a disaster fast.
@marbella-elviria
@marbella-elviria Жыл бұрын
Is this for children who start learning English?
@maixechrys6264
@maixechrys6264 Жыл бұрын
Care to elaborate further?
@ganesh-Chennai
@ganesh-Chennai 3 жыл бұрын
Hello friend, I think you're messing up with your battery. Li-ion cells must not be exposed to long duration heat..you see, it destroys the capacity of the battery.
@maixechrys6264
@maixechrys6264 3 жыл бұрын
Yes, long duration heat should be kept to a minimum.
@maatiraouki5183
@maatiraouki5183 Жыл бұрын
👍✌️❤️
@vikasshukla85
@vikasshukla85 3 жыл бұрын
👍🏿🙏🏾vjppjio
@alex13261911
@alex13261911 Жыл бұрын
Total wrong,every battery pack need a BMS 😢😢😢
@maixechrys6264
@maixechrys6264 Жыл бұрын
Its good to have, not a must please don't missinform. Tons of batteries exist in the market without bms. Even lipos, do you think a phone batery caries a bms?!
Beginner’s guide to building safe 18650 batteries
19:38
Teaching Tech
Рет қаралды 274 М.
How To Make A Lithium Battery Pack With 18650 Cells | Practical Skills For Makers
15:44
Mom Hack for Cooking Solo with a Little One! 🍳👶
00:15
5-Minute Crafts HOUSE
Рет қаралды 23 МЛН
Tuna 🍣 ​⁠@patrickzeinali ​⁠@ChefRush
00:48
albert_cancook
Рет қаралды 148 МЛН
Что-что Мурсдей говорит? 💭 #симбочка #симба #мурсдей
00:19
Discovering SHOCKING Electrics - ØY Africa Special
11:12
Cory Mac - ØY Electrical
Рет қаралды 7 М.
DIY li-ion packs! How to solder mains and balance leads.
11:27
Dane Martin
Рет қаралды 7 М.
Making Car Jump Starter PowerBank
16:00
Creatividea
Рет қаралды 254 М.
DIY 18650 4s battery packs
14:11
RC Escape
Рет қаралды 41 М.
“DIY: Building a Li-on 6s2p FPV Battery Pack from Scratch”
19:56
Voodoo Nation Production!
Рет қаралды 6 М.
INFINITIVE BATTERY | New Invented DIY Battery | Free Energy.
18:09
Joy of Electronics
Рет қаралды 100 М.
How-to Make 18650 Li-ion Battery Packs
13:27
RC Video Reviews
Рет қаралды 16 М.
Make your own Li-Ion Battery Pack
7:15
GreatScott!
Рет қаралды 1,4 МЛН
Making 2S 18650 Li-on Battery Packs for RC FPV Models
39:03
RagTheNutsOff
Рет қаралды 60 М.
Mom Hack for Cooking Solo with a Little One! 🍳👶
00:15
5-Minute Crafts HOUSE
Рет қаралды 23 МЛН