Very good, the better homemade grooves i see on KZbin!
@hulababagamer35222 ай бұрын
We are waiting for accuracy testing
@markjonior2 ай бұрын
Very beautiful. But it is worth trying by pulling... pulling is better than knocking, but it is also nice. We are waiting to try the accuracy on target papers.
@pcpairgunschannel2 ай бұрын
I might make a press to push buttons one day. I am still gonna experiment
@markjonior2 ай бұрын
@@pcpairgunschannel Good luck, brother, you are amazing
@Pauly51502 ай бұрын
Great work. It will be interesting to see how it groups once it's finished.
@markjonior2 ай бұрын
@@Pauly5150 Yes, it would be good to see the accuracy of the assembly at a distance of 20, 30 or 50 meters. I hope for a wonderful group for assembly. 😍😍
@auriceliosantos82342 ай бұрын
@hughstewart3244Ай бұрын
Using a hydraulic jack will give you more control to push the reamer through the barrel
@pcpairgunschannelАй бұрын
I will make a set up one day.
@detoderos2027Ай бұрын
Hola hay que volver a templar el escariador despues de haberlo puesto al rojo vivo y torcido con el alicates?, gracias
@pcpairgunschannelАй бұрын
Yo no hice eso. Funciona bien si el cañón no es demasiado duro.
@detoderos2027Ай бұрын
@pcpairgunschannel osea no es necesario volver a templar el escariador,quisiera ver algunas pruebas de tiro ,visite ti canal pero no encontré ninguna
@LowkeyAirgunner2 ай бұрын
Not too shabby! I am curious to see the accuracy Some people in the comments really need to show us how it is done. {So we can laugh}
@pcpairgunschannel2 ай бұрын
@@LowkeyAirgunner this will be for my semi auto. Its gonna take a while to make it, I will order some more materials
@David-p9y9c18 күн бұрын
I might suggest fire lapping but it’d probably rupture
@Александр86-у9дАй бұрын
Молодец,отличная работа
@sanchezicАй бұрын
Для дорнования нужно использовать спец смазки в виде покрытия внутренней поверхности, медью, свинцом или серой, использовать масла это риск задиров или заклинить дорн.
@Данил-ъ7я1гАй бұрын
Ото с дуру можно все сломать .кто профи!!!🎉
@Vovastik1702 ай бұрын
я сделал дорн из сверла, электролитическим травлением. сверло по металлу дешевое, закалка не нарушается, и диаметр можно подобрать с точностью до 0,1 мм. отличный вариант для тех, у кого из инструментов только молоток)
@sanchezicАй бұрын
Да я на дорне канавки тоже травил только медным купоросом с солью, а потом и вовсе начал делать полностью на токарном канавки под нужный твист с помощью прямозубой накаткой, так получаются очень точные дорны.
@RDX-8200Ай бұрын
@@sanchezicа зачем это всё нужно, если готовых бланком везде навалом и стоят они недорого?
@snarkyjay474410 күн бұрын
It's an interesting video. Did you heat-treat the reamer off-camera? Just curious how hard the bit was after heating it for reshaping. Lands and grooves are usually wider than what this would make, but for a do it yourself technique, it's cool to see. I hope you chamber the barrel and do some accuracy testing. It would be cool to see the projectile with a high-speed camera. Thanks for posting!
@pcpairgunschannel10 күн бұрын
I didn't heat treat it again, it's for an air gun so the lands to grooves ratio is not that strict
@earlmiller609322 күн бұрын
Turned out pretty good actually… What rate of turn did it result in?? Looks about right…
@pcpairgunschannel22 күн бұрын
The twist rate is too high, its 1:10, i will still experiment more rifling techniques and come to a conclusion.
@mrkalikutista87292 ай бұрын
Can you show us the actual testing to see how accurate it is?
@pcpairgunschannel2 ай бұрын
@@mrkalikutista8729 I will once I finish my semi auto
@LuisFelipeGonzalez-kd8uz20 күн бұрын
Quebbuen trabajo amigo me puedes decir que numero de broca usastes para perforar el metal 2 de diciembre 2024
@matthiasbohm259320 күн бұрын
Nice, but will you put a cartridge in it, ignite it and watch if the barrel withstands 60000 psi?
@pcpairgunschannel20 күн бұрын
The barrel needs to be hardened. This is just for a PCP rifle though, so no need.
@Drillz007Ай бұрын
you hammer very quickly i am impressed
@Адлан-л4ыАй бұрын
Перевести. На. Русский
@richards62692 ай бұрын
Nice work, really loving your videos. That's the best DIY button rifling button I've seen being made and using the 6 flute reamer was the best starting point I've seen too. The big question with all these DIY rifling videos is, can the barrel take standard pellets or must you make your own to the exact dimensions of your barrel? I say that because even expensive barrels are choosy at the best of times, you'll get tight groupings with one brand and flyers with another.
@pcpairgunschannel2 ай бұрын
From my experience in general most diabolo pellets work well. Since the grooves are a bit thinner using this method, it is best to keep it under 30 ftlbs to keep good accuracy.
@richards62692 ай бұрын
@@pcpairgunschannel Good to know. Have you tried slugs?
@pcpairgunschannel2 ай бұрын
@@richards6269 not yet.
@richards62692 ай бұрын
@@pcpairgunschannel Thanks for interaction. I've watched possibly all the DIY PCP videos on youtube and you stick out a mile as the channel to watch. Again, nice work and thanks.
@pcpairgunschannel2 ай бұрын
@@richards6269 I really appreciate your feedback!
@benoitdudzik2 ай бұрын
super video like always
@marcosalmeida2098Ай бұрын
Se fizer isso num cano de uma 36, funciona bem com balas e cartuchos??
@pcpairgunschannelАй бұрын
Talvez, mas vou usar isso para uma arma de ar comprimido. Para armas de fogo, um botão de raia comercial é a aposta
@marcosalmeida2098Ай бұрын
Obrigado@@pcpairgunschannel
@DewaSenapanIndonesia2 ай бұрын
Very useful knowledge 👍👍
@pcpairgunschannel2 ай бұрын
Thank you sir! Your videos are amazing.
@cazadorversatilrsАй бұрын
Cuantas veces hay que pasarlo
@arnoldnazaire615415 күн бұрын
In one revolution how many inches?
@pcpairgunschannel15 күн бұрын
1:10
@motoimz43023 күн бұрын
Ну, а кучи какие получились? Лист А3 или А1 на сто метров?!
@sbp42..2 ай бұрын
Только раб не имеет права сделать себе оружие ✊
@ВольноеСердцеАй бұрын
не будем, такими 😊
@murataflytunov22316 күн бұрын
У нас в России сразу под статью попадёшь за изготовление ствола или за хранение. Можно и на нары загреметь
@rafaozga46552 ай бұрын
Nice work ,did you use 5.5 or 5.45mm pipe? link doesn't work
@pcpairgunschannel2 ай бұрын
sorry, link might have expired s.click.aliexpress.com/e/_DdOotUh I used 5.48mm pipe
@hofrasgaming73878 күн бұрын
sadly, this is not how rifling works... but i like the video. very interesting way to use reamers for cutting lubricant lines into bushings. good job👍
@pcpairgunschannel8 күн бұрын
This definitely isn't an ideal rifling technique for firearms, true. But for air guns this can give decent or even fairly good accuracy.
@P.Trim69Ай бұрын
Thanks for making and sharing these videos with us.
@jpcaretta8847Ай бұрын
Nothing worth in this !
@Gabriel-rn1si2 ай бұрын
It would be interesting for you to pass a miniature camera inside the barrel to see how the soul finish turned out
@pcpairgunschannel2 ай бұрын
@@Gabriel-rn1si lets see if one day its affordable.
@posadaszproduction2 ай бұрын
Amigo . Que tipo de material es el escariador . ?
@pcpairgunschannel2 ай бұрын
HSS high speed steel
@posadaszproduction2 ай бұрын
@@pcpairgunschannelsera el mismo hierro de las llaves hexagonales ?
@posadaszproduction2 ай бұрын
@@pcpairgunschannely el cañon que material es? Esque quiero pasar un cañon de 4.5 a 5.5 de acero .
@@pcpairgunschannel And what do you recommend? I want to upgrade a barrel, from 4.5 to 5.5.
@hulababagamer35222 ай бұрын
Bro can i try it carbon steel 6.5 mm tube is it worthy for me, which button good i for fine rifling hss,tungsten carbide,or cobalt please tell me
@pcpairgunschannel2 ай бұрын
If you use this reamer method then use hss. Tungsten carbide and cobalt are harder, but they are more brittle. Due to that you would risk the button breaking if you used carbide
@hulababagamer35222 ай бұрын
@@pcpairgunschannel thanks a lot for your value able suggestion, i will try
@thefunstuff6121Ай бұрын
It's pretty, but not going to be much use. The lands are 95% of the rifling and will create a huge amount of drag. They should be about 33% of the rifling, with the grooves 66%. Also, what is the twist rate
@pcpairgunschannelАй бұрын
it is 1:10 this is for air guns only, it works quite well on air guns.
@jesensunjaya388227 күн бұрын
@@pcpairgunschannel I preferred choose twist rate 1:16 for airgun
@pcpairgunschannel27 күн бұрын
@@jesensunjaya3882 yep thats the best. I would have done that but it isnt easy to manipulate the twist rate
@mordimustafa12752 ай бұрын
Nice job😊 can you tell me where i can buy good quality Teflon for making valves please
@pcpairgunschannel2 ай бұрын
I dont know a place apart from AliExpress
@mordimustafa12752 ай бұрын
@@pcpairgunschannelsend me the link please
@mordimustafa12752 ай бұрын
@@pcpairgunschannel please send me the link
@pcpairgunschannel2 ай бұрын
@@mordimustafa1275 s.click.aliexpress.com/e/_DdPb4XF you want to use it for the firing valve right?
@mordimustafa12752 ай бұрын
@@pcpairgunschannel yes I want to use it for the valve and the refilling port too
@zeeshaneastchem73872 ай бұрын
well done and very neat and impressive
@xzvoss1526 күн бұрын
22lr?
@pcpairgunschannel26 күн бұрын
.22 PCP
@CyberHunter512Ай бұрын
Barrel groove very nice, however manual tool , i wait for tes accuracy ..mr ..👍👍
@karlalton31702 ай бұрын
Awesome job bro 😎😎🤘🤘
@prasunmajumder7575Ай бұрын
Size of the reamer?
@pcpairgunschannelАй бұрын
5.6mm
@RafaelCespedeLeyva2 ай бұрын
Buen trabajo compañero
@Japs_Eye_Of_The_Tiger2 ай бұрын
Great channel.
@antoniodellaragione60912 ай бұрын
Ottima LAVORAZIONE 👍👍👍👍👍👍 calibro 22 ??? Aria compressa ??? O altro ???? aspettiamo continuo 👍
@pcpairgunschannel2 ай бұрын
Sì, è per un fucile ad aria compressa calibro 22
@Skulptur16 күн бұрын
يجب ان يكون الحلزون نافر وليس غائر
@fullgas1413Ай бұрын
Ótimo trabalho.
@RiyameАй бұрын
Another way to polish a crown is to put a brass round head screw into your drill chuck in the steady rest and put some polishing compound on it then run it against the crown.
@baklasbaklas27 күн бұрын
Is this 22 barrel brother
@pcpairgunschannel26 күн бұрын
yes, for an air gun
@baklasbaklas24 күн бұрын
@pcpairgunschannel I mean 22 rifle
@pcpairgunschannel24 күн бұрын
@@baklasbaklas It isn't intended for that, its for a pcp air gun. But you can use the same rifling technique for a 22 rifle
@locodriver6012 ай бұрын
Put a rest close to the wheel BEFORE you loose your fingers. What you are doing is very dangerous. (I saw a man loose half his hand when I was a young engineer 50 years ago)
@pcpairgunschannel2 ай бұрын
@@locodriver601 in that case I think I will but how will a rest prevent an accident
@locodriver601Ай бұрын
@@pcpairgunschannel It stops the work piece being dragged under the grinding wheel along with your fingers. You will also have better control of the work piece. Keep safe.
@pcpairgunschannelАй бұрын
@@locodriver601 for some reason my bench grinder came with no rest at all. would it be any less dangerous if i completely removed the guard around the wheel so that nothing could be pulled under the wheel?
@locodriver601Ай бұрын
@@pcpairgunschannel Not a good idea. You should keep the guard and make yourself an adjustable rest. It should be quite easy to do. A bit of time and effort is better than injury to your fingers.
@justicar5Ай бұрын
@@pcpairgunschannelno, that removes the protection in case of the stone shattering/coming loose.
@Frakiez2 ай бұрын
Здоровская подзорная труба получилась.
@井上智樹-m7o8 күн бұрын
実際のライフリングの製作は油のなかで油圧でライフリングのカッターを引き抜いてカットしますよ!
@raygordon1822Ай бұрын
Well done!😂
@brantonzhang19 күн бұрын
Could you make the zip gun from the movie Munich?
@pcpairgunschannel19 күн бұрын
@@brantonzhang i cant make actual firearms legally, only air guns
@brantonzhang19 күн бұрын
@ I meant to say prop air gun
@pcpairgunschannel19 күн бұрын
@@brantonzhang Maybe I could make something like that one day, but its not in my plans
@jofjofjofjofАй бұрын
how much?
@nirdoshbara36182 ай бұрын
Nice bro ur great
@stephengrimmer3521 күн бұрын
I presume you skipped over the hardening (heating, quenching, annealing) of the rifling button.
@nhanquyenang65982 ай бұрын
Dao kéo rãnh khương tuyến có phải bạn làm từ mũi doa không?
@zlatkovuckovic64432 күн бұрын
Nice wokk
@thisstuffido914110 күн бұрын
Cool
@HARSHADHD-x8l14 күн бұрын
Amazing work
@kuazetudo8583Ай бұрын
Perfect
@mikevidahltv19442 ай бұрын
Hammer Geile Arbeit mache auch Handarbeit macht Geile Luftpistole
@bigrod00697 күн бұрын
👍👍
@joshkelly37435 күн бұрын
Now to see what it likes.
@HibatLehri22 сағат бұрын
❤❤
@RDN_Hunter2 ай бұрын
Nice video
@НиколайЗахаров-ь3я2 ай бұрын
Сколько лет дают за такое рукоделье?
@miko9588Ай бұрын
С добрым утром! Лучше не вопросы задавать, а ук рф 222 и 223 читать, затем фз-150 "об оружии", и знать, что пока заготовка ствола не имеет патронника, пригодного для осуществления выстрела - заготовка не является основной частью оружия и не подлежит никакому учёту. Название канала - про PCP винтовки, у которых нарезы есть, а патронника - нет. Ещё раз с добрым утром, просыпайтесь быстрее.
@gaurabpattnaik13832 ай бұрын
👍
@gerritmeester33902 ай бұрын
Using a spiral flute reamer rather than a straight flute reamer would make creating the rifling button much easier.
@pcpairgunschannel2 ай бұрын
@@gerritmeester3390 spiral flute reamers have a too high twist rate
@robertqueberg4612Ай бұрын
You are receiving compensation from youtube to teach peoplesomething worthwhile. Yet you continue to use a benchgrinder without a toolrest. Have you ever seen a picture of a human finger that was pulled down into the ever decreasing space between a spinning abrasive wheel and the mounting bracket that was designed to hold the toolrest. I worked as a toolmaker all of my working life, and have grabbed a shop towel to wrap around the finger of one fellow worker. A decent portion of the first joint was chewed away. I have ground nicks in my hands annd fingers over the years with the guards in place. Abrasive wheels are filthy objects that transfer that dirt to your open flesh as it is burned. Some of these do get infected. Keep a bottle of hydrogen-peroxide in your tool box, and put the damned guards back in place.
@pcpairgunschannelАй бұрын
It never had guards in place. Since two people have said for this now then I will look how i can install them on.
@pcpairgunschannelАй бұрын
do you mean that I should simply add a rest, nothing complicated right? I got no rest when I bought mine... I have to make one by myself probably. possibly a production issue
@P.Trim69Ай бұрын
Yes Sir it is dangerous to not use tool rest, little table, shelf etc. ur really lucky enough to have people to kinda give little hell so it doesn't cause a lot of hell in the future. Because it will eventually happen. Might not be real bad and on other hand. One could loose a hand. Maybe a life. They are very dangerous . Ok take care I love the channel id hate see a tool get a piece of you. Stay safe from ur ole hillbilly buddy
@glenkearns54Ай бұрын
Live dangerously lol
@glenkearns54Ай бұрын
Great video !
@P.Trim69Ай бұрын
Yes Sir nice
@andifebriheirizaman63892 ай бұрын
Berapa twist rate nya tuan?
@pcpairgunschannel2 ай бұрын
1:10 terlalu tinggi jadi saya akan menggunakan lebih banyak teknik segera
@andifebriheirizaman63892 ай бұрын
@@pcpairgunschannel tidak cocok untuk pcp tapi cocok untuk senjata api. Kerja bagus, lanjutkan
@MNhunter882 ай бұрын
Nice
@alfonzoidalgo90912 ай бұрын
Yes
@AbuBaker-o9kАй бұрын
Твист на глаз сделал? только для воздушного оружия подойдёт.для точного оружия такое не годится
@pcpairgunschannelАй бұрын
да, это для пневматического оружия
@seniperfr73612 ай бұрын
😱👍💪
@ping62462 ай бұрын
😀diyer‘s god
@adcaptandumvulgus42522 ай бұрын
I'm amazed when you put the heat on that thing it didn't get soft as pot metal
@CarlomanEleriaАй бұрын
Megustaria.arquirir.uno.donde.puedo.conplarl
@pcpairgunschannelАй бұрын
not for sale, sorry
@elstaso2323Ай бұрын
Толку от этих канавок, только газы будут уходить. Нужны наоборот выступы, которые вгрызаются в пулю, тем самым её закручивают.
@БашибузукМафусаиловичАй бұрын
Какой твист нарезов получился? Судя по видео, короткий, 10-12" Если для рср то это плохо, кое как может быть кучно будет лететь волан типа jsb. Про слаг даже не мечтай. Такова реальность.
@pcpairgunschannelАй бұрын
1:10
@Brett_M2 ай бұрын
Ya I couldn’t rifle my 9mm barrel. I couldn’t get it in the press straight enough.
@pcpairgunschannel2 ай бұрын
that's unfortunate... What kind of button do you use?
@Brett_M2 ай бұрын
@@pcpairgunschannel one of those carbide Amazon ones.
@pcpairgunschannel2 ай бұрын
@@Brett_M do you have discord yet?
@Brett_M2 ай бұрын
@@pcpairgunschannel brett_m_yt
@Brett_M2 ай бұрын
@@pcpairgunschannel yes
@frankieguyi27412 ай бұрын
Put on gun barrel and test it
@zhairatahiriАй бұрын
عمل جيد لكن لا يمكنني المجازفة ، أخاف أن يعلق
@Igor_SavitskyАй бұрын
Могу представить себе точность такого ствола :))
@vasssabАй бұрын
Это идиотизм товарищи! Просто уничтожить бланк ради чего? Один нарез глубже, другой мельче, никакой стабилизации
@denezar-g4o2 ай бұрын
top,..
@НиколайИващенко-е8ъ2 ай бұрын
Исполнение не точное.😊😅😂😢
@matdeen97352 ай бұрын
Land is too wide, not good for accuracy
@pcpairgunschannel2 ай бұрын
@@matdeen9735 it does work for air guns
@tvsettv24 күн бұрын
Don’t do that way. It is a wrong way
@pcpairgunschannel24 күн бұрын
works well for air guns.
@russbernard8666Ай бұрын
Just so u know. You can buy premium carbide rifling buttons from eldorado the GUNDRILLING machine dudes. They are inexpensive and precision versus your shade tree wanna bee a machinist road warrior bs. To much meth make you crazy
@pcpairgunschannelАй бұрын
I cannot hammer them. This is an inexpensive rifling method, commercial buttons need a press.
@aryanpriestАй бұрын
You ruined the bar
@pcpairgunschannelАй бұрын
how
@СергейДесятник-к4ж11 күн бұрын
Это не нарезы,а фуфло. Автор не имеет понятия о нарезах ровным счётом ничего.
@tempesttempest769Ай бұрын
FBI wantw to know your location
@miko9588Ай бұрын
This guy is certainly in Russia. Our gun law allows anybody make any blank barrels they need. Unless you drill a cartridge chamber, it's totally legal. Bad thing is: if you drill that chamber, you get a prison term the same moment, up to 7 years.
@smalltownrifleman12 күн бұрын
NOPE!
@stansmith19112 ай бұрын
so let me see here..... you heated up the reamer until it lost all its hardness and then you hammered it down a tube that is to be a bare of a gun then your going to make it into a gun and shoot it. First of all the reamer was soft and hammered down a soft tube which no bullet should be fired through it because it is so unsafe. It don't work that way and if people follow you and do that there going to get hurt or even killed. And yes I work on guns. I know. some of those barrels are so hard you have a hard time getting a cobalt drill bit to penetrate the steel and you going to do what? nice video but I hope no one does that. So now let be your advocate. So the next step is to harden the barrel if it can be. then proceed to the next step.Im not saying what the next step is. But I do know. Again nice video. I would have heated the tool after I got the right twist in it and then put it through the tube.
@pcpairgunschannel2 ай бұрын
This is common knowledge for someone who wants to build a firearm However, this is not for a firearm. It is for a PCP air gun