Making barrel rifling using steel tubes

[@pcpairgunschannel]

Help fund future builds here: buymeacoffee.com/pcpairgunschannel Every bit helps keep the creativity flowing!🔥Thanks so much for all the support lately! 🙏

[@richardharding7767]

I just wanted you to see this. Some good hardwood "soft jaws" for your vice, and a solid brick or tile for your anvil while heating will help the part stay warmer while while working. The metal jaws of the vice absolutely drain the heat from the part your working. Good work bro.

[@doganilehersey7138]

Merhaba türkiyeden selemlar 6.35 namlu için düğme çapı ve tüp borunun iç çapı ne olmalıdır

[@pcpairgunschannel]

@@doganilehersey7138 selamlar, tam olarak bilmiyorum ama bence genel olarak iç çapı 6.3mm-6.35mm iyi çalışabilir ve düğme çapı 6.45mm-6.55mm olsun, en az 0.15mm farkı lazım. Google'den bunları daha iyi çekebilirsiniz.

[@doganilehersey7138]

@@pcpairgunschannel çok teşekkür ederim

[@pcpairgunschannel]

@@doganilehersey7138 ne demek 👍 Nerelisiniz acaba?

[@bolderiks]

Nice video and very educative. But an urgent message from my side: NEVER WEAR GLOVES WHEN WORKING ON A LATHE ! The chance that your glove will be caught by a rotating workpiece is significant. You can imagine what this does to your fingers... or even worse. In my career as a technician I once witnessed a young guy who was found death on a lathe. It was a horrible experience. He was working alone in a shop. He wore gloves while working on the lath, he was sanding/polishing a rotating piece of tubing in the lath. The rotating tube caught his glove, then his sleeve and then his work jacked. The poor boy was strangled to death. The lath blocked while the motor kept running, the V belt started to heat up and caused a lot of smoke that came out from under the door. People in the area noticed this and so they went inside the shop and found the poor guy. Even now I get goosebumps when I think about it.

[@rickwoud4319]

something similar once happend to me. during the first few month as an apprentice i worked alone on a drillpress in the shop for the first time. did some special parts and wore gloves. it was a rather big and weird shaped piece of metal so i coudnt fixate it to the vice, so i was holding it. than it slipped out of my hand and a sharp corner cought my glove and ripped if from hand and instantly wrapped it around the drillbit/workpiece. luckily that was not my hand. never ever wore gloves around spinning machines and always fixed workpieces in a vice since then.

[@hope4ourfallen]

There was another video that my eldest son showed me too. I've never been more terrified of a price of equipment as I was when I saw the poor guy get basically rolled up by an industrial lathe. It was beyond horrifying to watch as his clothing was about all that held together as it wrapped him Backwards onto the lathe while the repeated slams basically burst his tissues til there was nothing left😔

[@frankenstone804]

I never wear gloves with any power tool like grinder chainsaw etc cause you dont have a good grip

[@TheWirksworthGunroom]

Agreed. I wear gloves when using power tools that you can pick up but never on ones that are fixed pieces of equipment such as lathes, mills, bench grinders etc.

[@davefellhoelter1343]

"I hate" fingers "Still in" gloves still spinning round lathes and drill presses! Thump, thump, thump, and the cry of less decimals on the digits. Hearing PPE. think twice, slow down, What? could go wrong?

[@robertsimpson6324]

I made a sine bar machine which allows me to make different twist rates but a lot of work...this method you come up with is perfect for people with minimal tooling excellent idea mate well done

[@pcpairgunschannel]

Sounds great! Yes, this works really well and can be made with just an angle grinder, torch and some very basic tools. The end result looked better than I expected, very clean grooves.

[@arpadlimanagy7018]

Cano calibre 22LR ou 3,57 Magnum?

[@CrashRacknShoot]

​@@arpadlimanagy7018it's a 5.5mm ID tube, so .22-ish.

[@robertarthurs328]

​@@pcpairgunschannelI was thinking a bolt extractor might serve the purpose

[@pcpairgunschannel]

@@robertarthurs328 Which purpose? I didn't understand, sorry

[@miguelangellv1976]

Realy? I can't believe it! For at least twenty years I've been trying to rifling. I never thought that would be so easy. It is true that until a few months ago you could buy inexpensive rifling buttons online, but they were not available in all calibers. Now I don't see them on Aliexpress anymore, and the ones on Amazon are very expensive. Furthermore, the ideal is make the barrel from a steel bar. Using Allen wrenches for rifling is a fantastic idea. Congratulations!

[@pcpairgunschannel]

Thanks! The quality of this rifling of course isnt as good as what a commercial button can produce, but I definitely was satisfied with the accuracy I achieved with this. The accuracy is similar to most decent-high accuracy PCP air guns.

[@firangi999]

The best video I've seen today. Engineering is the only way to create something

[@AKAtheA]

a tip for further rifling experiments - you can grind carbide tooling at home, either slowly with corundum wheels or a bit faster with diamond tooling. You can buy blanks (will make your wallet sad) or find a machine shop that uses carbide endmills, they should have a few broken ones they might be willing to part with for little to no money also - lathe+gloves=bad, possibly very bad injury waiting to happen

[@pcpairgunschannel]

Thanks for the tips.. I have stopped using gloves while operating a lathe long ago thankfully. I will consider your carbide tooling idea, I will test many more rifling methods on this channel.

[@justotalkalottashit8392]

carbide tooling will just shatter with this method, too much impact for such a brittle material

[@arnoldnazaire6154]

Looking forward for more videos 👍♥️​@@pcpairgunschannel

[@TheWirksworthGunroom]

A good video on what can be done with minimal tooling but I would suggest to make it easier: 1. A 7/32" allen key would have been the size you were after with less work. 2. A 7/32 hex socket would have been easier to do the twist of the allen key with. Nice job though, good stuff.

[@redmorphius]

I love this. Thanks for sharing. All the people complaining probably can’t even hammer a nail to hang a picture on the wall

[@ozielaraujo9222]

Simplesmente perfeito. Acho top demais o trabalho que você faz. Parabéns e que Deus te abençoe sempre. Abraço do seu seguidor aqui do Brasil.

[@HopeIsAlliGot]

Wow…. Never knew that making of rifle barrel can be done by such limited tools. But no doubt the hard work is appreciated 🙌🏻🙌🏻

[@davefellhoelter1343]

our ancestors did it in the 1600's with less. Just start.

[@HopeIsAlliGot]

@@davefellhoelter1343 and don’t how it came into their mind that 🤩🤩

[@davefellhoelter1343]

@@HopeIsAlliGot I would imagine watching nature? Water flow, chucking rocks, sling shots, arrows. spears?

[@Koljahansi]

You made the whole process of machining drill bits so much easier Allen keys why haven't I thought about it

[@saw76]

И стволы нарезает и в перчатках за токарном работает) ценный специалист

[@Salmo-e2o]

А где вы видели ключи шестигранники, чтобы они могли нарезать сталь? Любой ключ шестигранник, без проблем берёт напильник и надфиль. Если бы он сделал Дорн из побидитовой напайки для резца, это ещё можно было бы поверить , что это дорн, который может нарезать резьбу в стальной трубке.

[@evgenymusanov2970]

Нарезы неправильные.Широкие поля должны быть выбраны,а у него наоборот.

[@arturhovhannisyan3606]

​@@Salmo-e2oя тож думаеу что шестигранник меахкое он не может так зделат нарези

[@Salmo-e2o]

@@arturhovhannisyan3606 да это любому, кто имеет дело со слесарными и токарными работами, ясно как светлый день, дорн можно из обоймы подшипника изготовить, но твердую сталь, этот дорн не возьмёт и нет гарантии, что не расколется как стекло, а мягкое железо, нет смысла нарезать, даже на пневматику.

[@user-vb3bp4xw1q]

самый интересный вопрос - а где он взял готовые < стволы > такой длинны , и второй вопрос - а куда он собирается патрон вставлять

[@airgunningyup]

one of the best rifling jobs ive seen

[@pcpairgunschannel]

thank you! I hope it will shoot as good as it looks

[@sanchezic]

the width of the rifling should be greater than the width of the fields or the same, such a barrel will greatly spoil lead bullets, which means that the accuracy will be poor. I used to make a button on a lathe using a knurling with a straight tooth and a pitch of 1.2 mm, which was equal to 12 threads of 5.5 mm.

[@boomstick4054]

I was thinking you could start with a larger Allen wrench for the steel stock. Machine it to the standards you mentioned, for equal & flat lands & grooves, then heat & twist.

[@InvisibleCitizen]

A helical reamer can be cut to make a rifling button also. It takes a little finesse to push it through the rifle bore but it does work. Grind a lead on the end to help hold it centered then sharpen each flute. Push it through the rifle barrel with press with lots of lube. Chambering requires a lot more finesse!

[@radchad992]

Hey I work as a machinist I have a few pointers 1. Take those gloves off or you’re going to mangle your hand and maybe lose digits. 2. Buy a set of micrometers it’ll help get better results and tell you a lot more about your actual thickness. 3. Get a dial indicator to indicate your stock true, I’m assuming you do more lathe work and it’ll give you better results and save you headaches in the long run. 4. Look into getting a hex bar at the size you need made of 4140, or a tool steel if you can cut it, itll last a lot lot longer after a good heat treat and you can sit down with mics and a whetstone and smooth it out and get it perfect. 5. When youre ramming your button down the barrel use excessive lubricant the gun drill we run in the shop literally fills the entire barrel with pressurized cutting fluid, it save your tool and make a cleaner cut . 6. If you’re working on a budget you can get a bottle jack with a long stroke to drive the ram and button down the barrel this will help with the finish and accuracy as you’re not beating the button repeatedly but driving it consistently. It’ll also be less of a pain I did black smithing and a press cuts down on your arms fatigue 7. Idk what you’re using as oil but tapping oil works great and gives better finishes, tool life, and keeps heat off the part. Overall good job my dude.

[@pcpairgunschannel]

Thanks for the tips!

[@hunt3r827]

Lol.. The comments are priceless 'Thanks this lets me do illegal things in my country'. Others suggest better tools or a more sturdy frying pan. Since this is for a PCP airgun.. Ever thought of buying a break barrel airgun replacement barrel ? Last time I bought one myself was for a Benjamin Trail and it was like $25 shipped. For $110 you can get a FX impact liner (sold with various twist rates) and then solder or epoxy it to one of your cheap pipes, or wrap it with Carbon fiber. Sometimes something that can be made cheaply with the tools at hand cost more in money and time than a proven product off the shelf. Good luck!

[@pcpairgunschannel]

I cannot get any of them shipped to my country. This was an experiment and the barrel ended up being quite accurate, I will experiment more methods of rifling on my channel for sure.

[@jackmclane1826]

And sometimes making something bottom up is a lot of fun.

[@dajoro-iq4lq]

It's the satisfaction of knowing you've built the whole thing , not assembled parts from ebay.

[@CarlosManuel-wm2ud]

Buen desarrollo en el estriado de su cañón al menos una idea que muchas personas desconoce lo que sin trucos falta probar la precisión ahí es donde en realidad se obtiene el resultado de su trabajo 😊😊😊😊😊

[@TheDamnSpot]

I would have made the rifling cutter bit longer to prevent any possibility of wedging sideways into the tunnel. While highly unlikely, you are using impacts to drive the bit through and just a little bit of torsional momentum could theoretically cause one blade edge to really dig in and ruin your barrel. I forget the length to width ratio of what you need but it's not a lot longer than what you have. Just a thought. I think it's great even as is.

[@pcpairgunschannel]

@@TheDamnSpot 👍 This was my first time rifling a barrel, and I will still try many other methods

[@penguinclips9551]

Looked really good 👍

[@habzbozali]

*عمل جيد لقد اتحفتنا بمعلومة جيدة كانت خافية علينا منذ زمن بعيد* #تحياتي 🌹

[@squiremc]

I could not believe you crowned the most distorted part of the barrel. You should have used that end for the chamber, not the crown as elastic deformation can return the metal to its original dimensions under pressure causing eccentricities in the muzzle that will damage accuracy. Other than that and the use of gloves on a lathe, I think you did quite a good job.

[@DJBLUEPHOENIX]

I never knew that this is how you can do it!

[@andrsivohin8167]

Молодец! Я делаю кнопку из шарикоподшипника,потом на токарнике с помощью болгарки прорезаю нарезки.И да,лучше всего проталкивать получается мощной дрелью-перфоратором.Плюс смазка машинная не годится-лучше использовать олеиновую кислоту с литол-24.Удачи в хобби!

[@pcpairgunschannel]

Спасибо! Очень интересно 😮

[@manchagojohnsonmanchago6367]

Yep Hammer drill. Or an Air tool

[@faq_is_love]

Проталкивать лучше гидравлическим прессом.

[@faq_is_love]

@@pcpairgunschannel И да, на али и правда можно купить дорны для нарезей. Я раньше искал по запросу "rfling button" и ничего не находил, но по запросу "helical push drill" они вполне находятся.

[@sanchezic]

@@andrsivohin8167 Круто. Я тоже на токарнике кнопку делаю и на нём сразу накаткой делаю канавки, накатка прямозубая с небольшим уклоном и шагом от 1 до 1,5мм в зависимости сколько нужно нарезов. Смазка на основе серы, талька и коллоидного графита и желательно канал обрабатывать тиосульфатом, как то так.

[@dajoro-iq4lq]

I never thought id need to try this.

[@Osamhatr21]

In the end good and clean work but I wonder how much the grinding machine costs ‏‪13:16‬‏

[@pcpairgunschannel]

It was a gift, but I think it's about 70$-80$

[@edevane-valencia-productions]

Gloves and machines dont mix together very well... Stay safe.

[@katiestevens1397]

The most detailed video I've actually seen on this method to date and I've watched a few of them, keep up your good work my friend.

[@pcpairgunschannel]

Thank you!! 👍

[@greensun1334]

To make the button, you can use a drill bit as well, it's usually made of well suited HSS steel and you just have to drive it trough the barrel twice to get the necessary grooves.

[@pcpairgunschannel]

Yep, there are many more methods I plan trying

[@airsight2753]

That's really good rifling bro!

[@pcpairgunschannel]

Thanks! Let's see the results.

[@greggorio6259]

@airsight Idol. pariho kayong magaling gumawa ng airgun. Idol ko kayong dalawa.😊

[@springpistonriflefeverlone9611]

Super cool! I really liked it!😃👍

[@pcpairgunschannel]

Thank you! Cheers!

[@jimsworthow531]

can't stop the signal..

[@Yaya38937]

❤❤❤magnifique

[@healthbeauty7853]

Is it not possible to hammer a drill piece into the barrel to rifle the barrel.

[@greatman73]

Wow, you are a genius

[@LowkeyAirgunner]

You have slightly more patience than I do and im here for it 😂

[@pcpairgunschannel]

Hehe, let's see what projects I will do in the future. I am gonna try some more rifling techniques for sure.

[@zorinho20]

Gloves make me uncomfortable

[@pcpairgunschannel]

Yeah, while operating a lathe gloves should not be worn. I have quit that and won't be doing it again.

[@davefellhoelter1343]

@@pcpairgunschannel 100% bad! very bad, not Cool to make other people recover your finger and keep on ice while the ER decides ??

[@mrkalikutista8729]

I admire your work, but a rifling button is just about 12$ ishhh so it's not practical to waste your time make all those fuzz? Furthermore you are not even sure how accurate the results would be? If it fails, you wasted time plus the tube you ruined. So why not buy the real thing?? It cost just less than 20 bucks

[@pcpairgunschannel]

@@mrkalikutista8729 I would need more than just a rifling button. Commercial rifling buttons cannot be hammered and need tons of pressure, which will end up costing me a lot more than just 12$

[@mrkalikutista8729]

@@pcpairgunschannel you're wrong you can do the same hammering with the cheap commercial one. Or use a bottle type car jack to push the rod instead of hammering it. Google hammer button, it's a good button, im using that one, stay away from those cheap chinese craps.

[@gengiscu]

your mind is so limited

[@manchagojohnsonmanchago6367]

​@pcpairgunschanneive hammered commercial buttons on ebay.. l

[@RodrigoFernandez-td9uk]

​@@mrkalikutista8729 - Fun. You can also buy the stuff already finished. - Unavailability due to local regulations.

[@HarryPredator]

Monitor my friend 👍 from Indonesia 💯👌

[@AtimatikArmy]

Awesome technique!

[@bOBERmASTER]

наличие нарезов не делают стальную трубку стволом. при подобном способе продвижения протяжки в стволе, ствол гарантированно деформируется к тому же качество нарезов оставляет желать лучшего из-за задиров и после выхода пули из ствола полетит куда угодно кроме точки прицеливания. на мой скромный взгляд - данное видео очень абстрактно показывает как делать НЕ надо и в общих чертах знакомит с принципами создания нарезов в стволе

[@СлавичСлавный]

Воздушку нарезали. Под мелкашный. Доработанным метчиком. Ниче, приемлемо.

[@Gilb37]

De l’artisanat, belles rayures 👍

[@P.Trim69]

Nice great work ole biddy

[@jimsun2486]

Very innovative. Looking forward to use it in Pcp. 😀

[@GazaThug419]

Clean AF

[@karlalton3170]

Would it not be better to start with a 6 mm Allen wrench and grind it down to what you want ?

[@pcpairgunschannel]

That would work and I did try it but I didn't achieve as good precision with it. It's about skill so if you can manage to do it and keep the sides consistent in size then you can do it.

[@DewaSenapanIndonesia]

This is a good result, I have tried it 🇮🇩🇮🇩

[@pcpairgunschannel]

@@DewaSenapanIndonesia 👍👍

[@benoitdudzik8010]

tanks for the video super cool job !!

[@pcpairgunschannel]

Glad you liked it!

[@ping6246]

man, you are the true hero!

[@pcpairgunschannel]

👍😎👍

[@spacejunkengineering1351]

Very Nice Job !

[@mathiasromankiewicz5696]

And always wearing gloves on the lathe to ensure you're hands get ripped of😂

[@thomascarboni7727]

È venuta uno spettacolo bravo

[@francescoardito5690]

Bravo ci voglio provare anch'io 💪💪🙋

[@tankerboysabot]

This is good education for SHTF sitfuations.

[@pixelpixelpixel3181]

but what you wanna do with the barrel, use it as a straw?

[@t-rexs232]

Same method in the Philippines when they make airgun barrel.

[@M.T....]

Much like the internet, this a series on tubes

[@lerosh2226]

Had a .22 with a smooth bore barrell,,,power was magic and did not see any accuracy problems,,,smooth is cool dude ,?

[@pcpairgunschannel]

Rifling gives better results

[@BlueCrawfish]

That was very impressive hope it tests well I have always been impressed with what a machinist can build I wish I had you skills if you lived near me in Louisiana USA I would enjoy being a friend to learn things the laws here are very favorable for hunters and sportsman but demoncracts are working hard to take that away I wish you well and if you ever want to move look this way hats off to you 👍

[@grahamthebaronhesketh.]

How do you calculate what is the best twist rate?

[@pcpairgunschannel]

i don't know about what is the best twist rate, but 1:18 is a standard most 22 cal PCPs use. This is probably just a tiny bit higher than that, but not to the point where it would not function well.

[@grahamthebaronhesketh.]

@@pcpairgunschannel 1 in 18 that is interesting, I think Whitworths rifle was 1 in 20, whereas modern rifles are 1 in 7 to 1 in 12. Projectile weight makes a difference too.

[@pcpairgunschannel]

@@grahamthebaronhesketh. yup. This is mainly for air guns tho. They need A lower twist rate to avoid overstabilization. I tried using another method to make a rifling button, but it didnt end well. Got 1:6 twist rate and very thin grooves. I will upload the video on that technique just to share it but i will try that method again and fix my mistakes

[@Bangsoljirak]

Ok brother i am waiting next part for test👍

[@greggorio6259]

😮woww its great work again idol.

[@SolarCookingGermany]

Good result 👍

[@jonmart7962]

Excelente 👌👍

[@javierdasilva9064]

La idea es lo que hace evolucionar el ser humano, y que no se acostumbre a depender de lo que esta hecho sino a elaborar sus propias herramientas..Si las ideas no se hacen no sirven. Mi padre me lo decia..

[@pcpairgunschannel]

👍👍

[@jefersonarredondo6673]

Excelente amigo, esperamos las pruebas, nosotros podemos construir nuestras propias herramientas, ya que el button rifling se puso escaso, y costoso, hice uno de una broca de acero rapido

[@astrogildoaugustobragaaugu2434]

Esse aquecimento que vc aplicou ai já fez com que ele perdesse a resistência.Em seguida teria que ser temperado novamente ok...

[@jonmart7962]

Excelente👍 aporte

[@MrSteppingstone888]

Awesome guessing the steel tube and bars came from Alli express.. super tek brake cleaner spray cleans out oils super quick

[@StaPerRa]

Интересное видео. Вроде как это один из самых первых способов в истории по выделке нарезов в канале ствола. Да, для весьма посредственной по точности пневмы покатит, и- то после шлифовки канала ствола.

[@ThisMFINGuy]

No way cool man id love to c this fire

[@윤이레-b4y]

대단합니다. 만약 총열 내부에 강선이 없나면 어떤현상이 나올까요?

[@yvesbrandt1863]

Really good Works Bro. Gratulation. Best Regards from Germany.

[@pcpairgunschannel]

Much appreciated!

[@blacklisted4885]

Excellent. Ive seen ppl break many of the cheap chinese buttons that are the only thing available in many places

[@rick31869]

PURE GENIUS , THE PRODUCT AND THE MACHINIST ALSO !!!! IS THERE ANY WAY I COULD GET YOU TO MAKE ME A RIFLING BUTTON IN .50 AND .68 CAL FOR PAINTBALL AND LESS LETHAL MARKERS ?

[@pcpairgunschannel]

Sorry, I cannot ship items

[@rick31869]

@@pcpairgunschannel THATS A NEW ONE FRIEND , MANY PEOPLE MAKE AND SELL MACHINED PARTS , IS IT ILLEGAL ? THERE IS A LOT OF MONEY IN THE LESS LETHAL WORLD TO MAKE LIKE SPECIAL VALVES , BARRELS , DRESS UP PARTS , AMMO , END CAPS , TO MANY TO MENTION !

[@Kahsimiah]

You can't just buy a rifling button anywhere in the world. Some countries have stricter gun laws.

[@pcpairgunschannel]

yep

[@Bluecollar711]

How did you inner diameter twist it?

[@pcpairgunschannel]

Since the rifling button is twisted, just like a screw it will twist by force

[@samw2768]

The best rimfire barrels are mi rifling . "Minimal invasive rifling " tye projectile only needs enough rifling to impart spin nothing more. When the projectile is getting engraved by the rifling it has more spin drift from the wind hitting the rifling marks. Let that sink in

[@Mazarakis_Spyridon]

Is it necessary the water to contain salt for the heat treatment to get the steel hardened?

[@pcpairgunschannel]

If its not hardened the button will deform and not cut so well. You can also dip it in oil but you need to temper it so its not too brittle

[@Mazarakis_Spyridon]

​@@pcpairgunschannel I asked you, if the water for the heat treatment is necessary to be salt water. Is it?

[@pcpairgunschannel]

@@Mazarakis_Spyridon Yes, it won't work with just water. Edit: it actually will work, but won't be nearly as effective.

[@Mazarakis_Spyridon]

​@@pcpairgunschannel Thank you!

[@Pareczech]

Seriously man... nice work but gloves dont go near lathe!

[@jcoleburt]

How did you get the perfect twist in the rifling. ?

[@pcpairgunschannel]

since the allen key is twisted slightly, just like a screw it twists itself in the barrel. I will still experiment many more rifling techniques and see what produces the best rifling

[@jcoleburt]

@@pcpairgunschannel Thank you.

[@joesashiify]

How do you know how much twist your putting on the button?

[@pcpairgunschannel]

@@joesashiify its not possible to manipulate it You have to twist it eyeballing

[@Arturo277]

Excelente trabajo de la estria del cañón creo que ahora le haces la recámara para el casquillo o bala y el percutor

[@christopherramirez9645]

Can you make inner barrel for airsoft with groove as well? 6.01mm or6.02 mm inner diameter?

[@pcpairgunschannel]

@@christopherramirez9645 I dont think rifling works well for airsoft since the bullets are round

[@thedude8046]

Nice job man!👌 What kind of steel was the tube?

[@pcpairgunschannel]

It’s 40crmo Some kind of chinese Carbon steel

[@teofiloguayamismaslucan7257]

donde consiguió ese tubo para un 5.5 estimado.

[@pcpairgunschannel]

AliExpress. Enlace en la descripción

[@flatout1001]

cool work lad

[@pcpairgunschannel]

thanks man

[@jefersonarredondo6673]

Amigo esta llave allen en realidad se deja templar para hacer el estriado ?

[@pcpairgunschannel]

¿Cómo lo usarías para moletear? Lo siento no habla español

[@mrdumbum8199]

can u use the lathe for 4140 steel?

[@pcpairgunschannel]

Yeah, you can. Even on materials that are harder to cut like stainless steel it works fine, just as long as you use appropriate speeds and feeds and appropriate passes

[@mrdumbum8199]

@@pcpairgunschannel nice, i was looking for a machine with which i can mill the barrel from 4140 steel and rifle them with a button

[@t.h.o.r.]

Innovative!- but you can't 'upset' carbon steel on the back of an old frying pan. get a piece of railway track or a truck flywheel. Im off to watch some more of your videos. Ive had airguns for 50 years - and never learned so much. thanks

[@pcpairgunschannel]

@@t.h.o.r. Thanks 🙏

[@alfonzoidalgo9091]

Nice👍👍

[@ukash4ever]

Excellent idea, thank you for sharing! : )

[@pcpairgunschannel]

👍👍

[@endrymargam7863]

Gunakan steel wool bro,agar lebih bersih

[@pcpairgunschannel]

👍👍

[@2010nijal]

Where did you get the round bar from?

[@pcpairgunschannel]

the tube? i left a link to buy in the description

[@ameenattef469]

Really amazing. But why do you beat and knock over it after heating it?

[@pcpairgunschannel]

because it was only 5.55mm in diameter, that's not enough for rifling. I increased the diameter by doing that, it ended up being 5.62mm

[@ameenattef469]

@@pcpairgunschannel 😁😁😁Great, I thought that was likely, but I wanted to make sure.....but did you know why I wanted an Arabic translation? So that I can understand and follow what you are saying. Greetings

[@ЕленаТурлова-п7ж]

@@pcpairgunschannel Весьма оригинально и главное просто. при наличии расширенного разнообразия оборудования есть возможность делать нарезы более технологичней и точнее. я нарезал нарезы спецрезцом изготовленным из шестиперьевой развертки, ленточка режущей части шлифовалась до необходимого размера и длина этой ленты оставлялась на 1.5мм.это и являлось шириной нарезного канала. станок токарный с автоматической подачей суппорта. есть и ускоренная подача, ствол зажимается в патроне. ставятся малые обороты, из ствола выходит приваренная оправка к резаку из развертки. она зажимается в резцодержатель. патрон вращается ничего не происходит и тут включается подача ускоренная вправо. равномерно вытягивает оправку с резцом . при этом выходит и стружка. так как заточка режет металл в стволе. происходит именно нарезка каналов. ваш метод конечно более простой и многим доступнее, но он продавливает каналы. свинцовая пуля мягкая и принимает размер ствола. и даже по вашему методу пуле легче идти по каналам продавленным, они ведь гладкие без всяких там мельчайших зазубрин. ваш метод считаю оптимальным для самодельщиков......удачи вам и желаю быть осторожным с законами.

[@pcpairgunschannel]

@@ЕленаТурлова-п7ж 👍👍

[@sonakhuraijam7223]

How many long pcp gun berral ?❤❤❤

[@pcpairgunschannel]

this is 300mm long, but you can use 200mm, 400mm, 500mm, 700mm... anything you want. this will be used for a PCP pistol.

[@sonakhuraijam7223]

@@pcpairgunschannel thanku....how can I buying this pcp gun barrel..I want to this barrel..Plzz help me...

[@pcpairgunschannel]

@@sonakhuraijam7223 Due to courier policy i can't deliver my own products. You can make it the same way as I did it in the video, you can buy blank tube and rifle it yourself like I did it in this video. If AliExpress doesn't work you can buy it from ebay also, just search "hydraulic steel pipe"

[@ЕгорСавицкий-й3щ]

What twist you made in that barrel ?

[@pcpairgunschannel]

@@ЕгорСавицкий-й3щ it’s just eyeballed, no accurate maths. It still gave good accuracy, check my latest shorts video

[@dworkinbar]

Почему бы не чистить почти готовый ствол нормальным оружейным шомполом со сменными патчами, а не пихать внутрь бумагу стальным стержнем, чтобы не повредить нарезы?

[@pcpairgunschannel]

Это сработало бы, но идея заключалась в том, чтобы просто избавиться от грязи и масла

[@dworkinbar]

@@pcpairgunschannel OK, я просто поинтересовался

[@fabiogabriel676]

Eu queria ver o resultado desce engenhoca😂 se ficou bom ou não 😅

[@snakes111b]

so quality air gun with mechanism,only change barrel and have 22LR?Am i right?Can you give advice of some good cheap air gun?Thanx

[@LuisFreitas-y9b]

Como consigo um cano desse raiado