Peugeot 5008 particle filter additive level too low PatFluid , EOLYS ,DPF Fluid

Tools you need: 8-10 socket wrench, srewdriver, Additif for FAP
I want to show you also how to clean and how to regenerate but my camera did not record this piece. But to do this you must first start your engine and wait until your car is 70 degrees hot and then you start the procedure with diagnostic tool. The diagnostic tool will show you step by step what you have to do but first you must see there are no fault codes.
For more help or questions you can always contact me.
See you next time!

[@photographe06]

Just some advice if you plan on doing this: Eolys is very dangerous for your health. Wear strong protective gloves and be VERY careful about not touching Eolys with bare hands. Even on gloves, rinse immediately. Around 6:44 I see lots of Eolys on your hands - avoid this at all costs.

[@mistertechnic6313]

thank you for info

[@DanielRundkvist]

PDF filter hehehe.....made me laugh. Thank you brother! :)

[@mistertechnic6313]

no goed engelish :)

[@razvancirstea3639]

His English is not too good indeed but the video is realy helpfull. Thank you very much mate !!!!

[@mistertechnic6313]

:)

[@salvoturkey]

I swear to god about he is a Turkish but I cannot prove it.

[@mistertechnic6313]

Tespit dogru Burakcim :)

[@nicolacapuano411]

Salve se per sbaglio si ricarica entra sbaglita succede qualcosa?????

[@mistertechnic6313]

i dont understand your language ?

[@nicolacapuano411]

@@mistertechnic6313 traduzione in italiano

[@shurcer]

Hi Mister Technic! Thanks for the video. What software is required to reset the error after the job? Where are you located? How much do you charge for error reset? Thanks.

[@mistertechnic6313]

Hy you need diagnos for reset thank you for watching.

[@lipalipa3034]

Hello, where did you buy the eloys fluid kit ? And what kind of diagnose tool do you use ? Thank you very much

[@mistertechnic6313]

you can buy vehicle dealer .end you need with a licensed diagnosis

[@soyebravat8903]

Hi I've attached my kit to my Peugeot 307 hdi SW pouch. Liquid came in a Bottle with a tube attachment and some adapters but it doesn't fill the pouch?? Once all connected It goes through the tube all the way and It stops at the pouches valve but the liquid doesn't go in to the pouch. I've got the bottle high as possible, tube is vertical with pouch on the floor. Can you advise? Much appreciated.

[@mistertechnic6313]

@@soyebravat8903 take out the reservoir , begin refiling the addivite using the tube yuou must apply pressure end check to your tube is open or no normaly very simple .

[@soyebravat8903]

@@mistertechnic6313 by reservoir you mean the pouch? I was thinking of removing the pouch and connect directly the tube to the white valve on the pouch. For some reason I was applying pressure when it was connected to the valve on the box bit it just wasn't filling the pouch

[@mistertechnic6313]

@@soyebravat8903 yes take of out the pouch end begin refiling you go see it haw simple

[@selimekizmaz5461]

Usta keşke Türkçe anlatsan...

[@mistertechnic6313]

tesekurler islediginiz icin evet turkcede anlatsam iyi olur ama yurtdisinda oldugum icin ingilizcz anlatiyorum gine baska bi sorunuz varsa yardimci olmaya calisirim

[@nicolacapuano411]

Traduzione in italiano grazie

[@KIKIREZI]

Throw the efin cigarette away when working on car

[@mariancorb4346]

Very good arcadas

[@mistertechnic6313]

thanks

[@mariancorb4346]

Thanks very much

[@mistertechnic6313]

thank you for watching

[@ciprian1609able]

five touzen five 😍

[@roquilchacon5313]

Excelente