Out for a ride and the bike just stopped . After a long push home its time to investigate the cause .
Пікірлер: 26
@kan815k2 ай бұрын
On these types of belt driving scooters, no need to take the spark plug to release compression to push home.
@bikerdood11002 ай бұрын
You do if the clutch is jammed on
@sky1army423Ай бұрын
So what was the problem?? The clutch was stuck?
@bikerdood1100Ай бұрын
Undone itself I do show it
@meduubazi196610 ай бұрын
My moped (Viva city 2001) consumes a lot of fuel, what should I do?
@bikerdood110010 ай бұрын
Well two especially when restricted are quite thirsty Derestricting the variety pulley would up the gearing a little I expect you are basically full throttle everywhere and even a small engine isn’t very efficient if it’s flat out all the time Ours was derestricted and had a different exhaust so at 30 the throttle was only half open, it’s the problem with mopeds really Too slow and not even efficient when restricted
@kaushikrao78683 жыл бұрын
My moped (Peugeot vivacity) starts and switches off correctly (almost). The display on the moped never switches off, however, the engine does and all the other electricals (headlights, horn, indicators). This issue also led to the speedometer not working as well. Any advice on what could be the issue? I'm not experienced in anyways to handle this problem. Please guide me.
@bikerdood11003 жыл бұрын
Hmm It isn’t likely to be the switch , but you never know. More likely to be a short circuit . It’s often caused by when the insulation wears through and contacts the metal frame . These sort of issues happen on older bikes as the Wiring gets brittle and tatty, with those sort of problems the simplest thing is to replace the suspect wires .Trouble is it’s a scooter and there’s lots of plastic.it’s not difficult to remove but takes a while
@josephkrout9341 Жыл бұрын
@@bikerdood1100aq
@Stuxen2 жыл бұрын
This exact problem happened to me yesterday however i didnt reslly understand what fixed it for you. I took apart the clutch and didnt see anything weird. It makes a really horrible sound and i dont know how to fix it
@bikerdood11002 жыл бұрын
Well it was the big nut on the clutch that worked loose on the video Bad noise often rollers
@Stuxen2 жыл бұрын
@@bikerdood1100 I screwed the big nut tight but when i place the wingbell it does not spin really freely, when i turn the engine on it makes horrible noise from the clutch.
@junaidaslam12 жыл бұрын
My moped, after riding for 5 minutes, takes a lot of force before taking speed again. For example, if I stop at a traffic signal for a while and give acceleration, it takes a few seconds before moving again. What could be the issue? Could it be a dirty carburetor or something else?
@bikerdood11002 жыл бұрын
Could be fuel Or likely very worn rollers and belt
@junaidaslam12 жыл бұрын
@@bikerdood1100 Do you know how much a roller normally costs for this? I had a full tank Euro 95 fuel with oil level also up to the mark.
@junaidaslam12 жыл бұрын
@@bikerdood1100 Also can you please show me picture of a roller, i am still new to using these scooter... i would like to know how much the fixing can cost me. i alredy spent around 180 euros with not much success except some of the other minor fixes.
@bikerdood11002 жыл бұрын
@@junaidaslam1 I don’t know exactly. But they are not expensive , a change of spark plug may help too
@junaidaslam12 жыл бұрын
@@bikerdood1100 Ok Thanks a lot. I will try these things.
@chizi74562 жыл бұрын
Man don’t get a Peugeot 😭
@bikerdood11002 жыл бұрын
🙄
@chizi74562 жыл бұрын
@@bikerdood1100 I only say this as I’ve had a 2018 kisbee for about 5 months and spend endless amounts on it and it always manages to break
@bikerdood11002 жыл бұрын
Well the one in the video was owned by us for 20 years without problems. All about the maintenance.
@chizi74562 жыл бұрын
@@bikerdood1100 okay okay, my bad. Don’t get a new Peugeot
@bikerdood11002 жыл бұрын
Well Peugeot don’t make their own bikes anymore, they closed their factory in France and buy scooters in from China. I believe the quality isn’t what it was as a result of cost cutting. So the same old story really to be honest I don’t think the build quality of the major Japanese companies is where it use to be either, so the fact that newer bikes aren’t so good unfortunately doesn’t surprise me