Peugeot vivacity variator

[@zzpote2784]

I eventually performed the modification yesterday, it works well 60/62 kph on the speedometer. Very easy to do, the biggest job was to build a device to block the piston ; I used an old spark plug fitted wiith a bolt inside ...My son is very pleased to this big speed increase !!!

[@davidgriffin79]

So that's how it works: the angular velocity of the rotor overcomes the centripetal forces on the rollers; they move out pushing the plate which increases the radius the belt takes around the plate increasing its linear velocity. The washers prevent how far the belt radius can be increased around the rotor thus limiting the linear velocity and therefore maximum speed; interesting and noted for when I get one of these scooters for Summer.

[@jegbryrmegikke1]

Thanks alot man, exactly the same on speedfight 3. did it today and made my top speed increase by 15 km/h

[@Mihu24]

Thank you alot!! It was very helpful, i removed also that plate and from 45 km/h now it reaches 65 km/h !

[@urkent4463]

everyone before put back in the screw of the vario, clutch got to be pressed by hand, putting the belt in that vario has it's free room and not screw the vario on belt instead of iron

[@matsvinn1666]

I just did it on a looxor 50 cc and now it doesnt speed up at all. The gas works 1/20 Times. Answers?

[@pakssmsjsjsks8596]

i removed the restrictor plate and still its not going all the way up on the vario and its only runs 50kmh so what to do? to make itt little bit faster

[@JamesParus]

impact gun is usually the best way to open it. Compressed air of electric. Of course it could be hard to find one. it's best not to use excessive force against the piston.

[@JamesParus]

probably. Not sure. it's almost identical procedure in all brands and models.Sometimes the limiter could look different.

[@garlikas]

I tried to do this to my vivacity 100cc, but the centre of that axle looks like drilled at the centre and hammered with some kind of sharp tool to make it stuck, so I wasn't able to unscrew that bolt, even vith a piston stopper inserted into the cylinder. Maybe I was too afraid to use too much brutal force in case I could brake the piston. Do you have any suggestions how could I unscrew it in this situation? thanks in advance.

[@hdmatthew2]

So you remove washers & the big metal plate?

[@doresiibraimi4656]

Thanks man, i gained 15-17kmh morr on my speedfight 2 from your tips❤

[@persian1997]

Is this on the newer 2008- vivacity?

[@RicardoPenders]

I have a Peugeot Speedfight 4 (4t, 2v, Euro5) from 2021 and I had it done by the shop I bought the scooter from, they gave me the vario ring which is a plastic ring and they also tuned the original ECU to make it run faster, it's still restricted by the ECU at 58km/h but I want to change it again so the ECU isn't the restricting factor anymore but I can't find any information about my particular scooter and the videos that I find from Peugeot scooters don't match at all to my scooter which makes it even more difficult for me. If there's anyone who knows where to find any information about my scooter or a shop where I can buy parts for my scooter that would be very helpful to me, I'm looking online for months thinking that eventually other people would buy a new scooter which is the same one as I have but now that a year has passed I still can't find anything online, this is very frustrating because I don't trust the mechanic from the shop where I bought my scooter and as soon as the guarantee period has passed I'm not going to that shop anymore so I want to do it myself then but if I can't even find an online shop selling 3rd party parts or original parts even then it's pretty much impossible for me to do it myself making me dependent on some guy that I don't trust.

[@thecritic7355]

Hello my friene, does this work on a Peugeot Ludix Elegance?

[@mistercizy2569]

Which rollerset is the best for vivacity 3 50cc

[@Alikh-oz9li]

Hi . Please can I communicate with you about this bike

[@herrdoodlesmith511]

Does this change how my moped sound? Will you be able to hear that the moped is trimmed if you remove the restrictions?

[@sa6kad]

Great video! Do you know what is the size of the rollers in vivacity 3? I just bought one and want to derestrict it and change the rollers since they seam to be too heavy and the scooter starts slowly.

[@Rtmlonesoulja]

What size socket do I need to take of the nut ??

[@redzcammozz1612]

Can you put it back later so it goes back to the original condition?

[@JamesParus]

Yes.

[@iivariloukasmaki4205]

Thanks, was rly helpful. My max speed rose about 15 km/h.

[@pajuluomawildout2896]

Mitä pitää tehä en ymmärtäny

[@iivariloukasmaki4205]

@@pajuluomawildout2896 2:50 otat ton kehän pois tosta ympäriltä

[@pajuluomawildout2896]

@@iivariloukasmaki4205 jaa mikä on kolmel pultil vaa et sittekö pysyy paikallaa

[@pajuluomawildout2896]

@@iivariloukasmaki4205 ja toimii

[@iivariloukasmaki4205]

@@pajuluomawildout2896 Juu, mutta kato et muut osat tulee paikoillee

[@MrVeggis1964]

Hi! My son want a sp2 here in Norway. I understand that it sucks with 45-50 km/t So, after some googeling im not smarter. What would you suggest as a smart way to tune he's fb2? Without changing sylinder, carorator.. Thanks again

[@ThxiD4x]

Great vid! But can't you just remove the washers only and then put everything back?

[@JamesParus]

if you remove the small washers the bike becomes slower. but if you remove the whole big metal thing, then it has no limiter.

[@ThxiD4x]

Ok thanks! I'm not going to de-restrickt my speedfight 3 anytime soon as it's brand new, but can this damage my scooter etc? Do I have to remove other things also, to not risk damage the scooter? Just looking for maybe 10-15 km/h more speed.

[@JakeTintti]

ThxiD4x variator is like bicycle gears. Removing the limiter just gives you 'higher gear'. so nothing else is effected.

[@johannesgitarristen1]

before you take the belt off, that thing who looks like a stuck brick should i take that off?

[@jorgenbarosen2130]

thank you for this my top speed is perfect after this. Really helpful!

[@jennitoler8267]

hey can anyone tell me if I can do this to a 4t vivacity peugeot I've looked all over the Web helppppp me please

[@waskalien]

Just perfect, thank you so much

[@linasamv2072]

do i need to check it if my motorcycle doesn't start?

[@a.hasselplan8471]

No

[@PuckFifaHD]

You only need to get rid of the plate?

[@JamesParus]

Yes.

[@kskqkqjdjdaad4331]

Do you need impact gun for it or can you do it wihout ?

[@nicolaidahl4747]

Just be careful and use multible impact points to even out the pressure as a precaution.

[@sprinterkingVEVO]

do u drive whitout weights :o??? and how many grams if u have weights

[@organicbbqsauce2651]

Isn’t there another tool instead of a impact gun

[@alexschonenberg6577]

Do u know the weight of the rollers?

[@MrPIMPSV]

Nice video!!! Is this for the new vivacity peugeot? And is it diffrent by a 2 or 4 motor?

[@cjmnmoto2583]

Should u change jetting if you do this

[@JamesParus]

not needed, as the top revs don't go up. limiter in variator is like keeping car at third gear. this just lets it to change to higher gear.

[@GolysACSRP]

@@JamesParus how much km/h does this increase ur vivacity? so lets say first it goes 40 what does it reach after deleting the plate? Thnx

[@saifkhmiri5560]

@@GolysACSRP 75km/h

[@codemasterz6074]

Hey James I`ve just removed 6 washers from the screws (2 for each) and there is absolutely no improvement. My vivacity is slow as ever going 45 km/h. Do you have any idea as why would it be ?

[@JamesParus]

it works like that. if you put more washers its faster. if you remove washers its slower. Best method is to remove the whole plate.

[@codemasterz6074]

+James Parus Ah man I`m such an idiot. I`ve watched your video like 5 times yet I haven`t realised that YOU DIDN`T PUT THE PLATE BACK. I removed the washers put the plate back.. and I was surprised there was no improvement. Just now I realised that you don`t put the screws and plate back on. Thanks alot. Any other improvement on your vivacity ? I use it to commute daily and I could use a bit more speed. Cheers.

[@JamesParus]

+codemasterz :) i didn't do anything else as this is the easiest mod.

[@codemasterz6074]

what about changing the exhaust ? would it offer any improvements ?

[@JamesParus]

+codemasterz yes it would,but probably needs jetting changes too.

[@petje35]

New vivacity 4T. ?

[@nunoleite46]

Hello, there is no risk of the belt out? its the same on the vivacity 125cc?

[@JamesParus]

belt cannot go over the edge, it's so short. This is probably only suitable for 50cc version.

[@nunoleite46]

James Parus Thank You

[@MrSkelltown]

and how many km is now?

[@F34RxMW2]

how do you make it go 80?

[@vegardaspy8109]

you can remove the sealing in the beginning of the exhaust

[@antte_3114]

Kun mä otan ton peltikiekon pois nii ei kuule ku 40/kmh ja jos se on siinä nii 50/kmh

[@jakey591]

does this work on peugeot v clic?

[@Cooper3Sly]

What year is that peugeot? Or is it the same way on every year? Cos i have like 2010 and pretty new with this stuff. I'm sry for my english if there is something wrong. Thank you for helpful vid!:)

[@nxthfx175]

There all pretty much the same bud, as long as it's the same model everything will be the same, just better quality.

[@DTMotorcyclesEssex]

Good stuff mate 👌🏻

[@Za7a7aZ]

You probably already know this but because I am a scooter friend I would like to inform you that when an accident occurs which causes the insurance to pay big money to the other party involved you will suddently have a huge problem because of this little adjustment.

[@benjaminkantelus6966]

Kyä tunnistaa lausunnasta et on suomalainen

[@niklas8139]

torilla tavataan

[@japez420]

Jep

[@pajuluomawildout2896]

Mitä pitää tehä en tajunnu

[@victorhernandezcham981]

Thanks for video. It,s very clear.

[@luukas5312]

Miksi tuo rullakuppi tai se ei lähde irti vain vetämällä?

[@JamesParus]

Olisko erilainen tai uudempi malli

[@sasurintala6343]

@@JamesParus muistatko et mikä tän sun vuosimalli oli?

[@bournemouthrider3836]

Does it work on all Peugeots

[@JamesParus]

I have no information about other models, but I've heard some rumors that peugeot speedfight 3 al least has different structure.?

[@pyroclutch9061]

yes it does i tuned my peugeot zenith whit that and some more stuff but it works but it goes not from 45-50 to 60 its more like 45-55 my setup 50 cc DMP polini vario polini koppeling Red drukveer blauwe trekveren sito plus eronder 8 gramm rollen snellere cdi

[@larsbuitenhuis6196]

I've a Peugeot Jetforce C-tech and it has a restrictor plate on it, some models may have a restrictor ring.

[@pyroclutch9061]

not on all peugeots be carefull because 4t is not ! and some c-tech d-tech not

[@larsbuitenhuis6196]

ringo heimans Luckly i've the exact same variator :)

[@tirppu4007]

oma viva menee ny 80 kiitos tästä

[@ingodwetrust9848]

Thank u for every thing .

[@pajuluomawildout2896]

Mitä piti tehä en tajunnu

[@andykerr3803]

So simple 👍

[@danielbaker5]

Guna try this today on my vivacity 100cc

[@Egyhorsnblood]

Thank you

[@JamesParus]

it's probably almost similar to all engines.

[@MrVeggis1964]

Thanks man :-)

[@jpa2217]

Missä se rajotin siis on

[@JamesParus]

2:55 kohdassa irrotettu peltikiekko.

[@jpa2217]

@@JamesParus selvä kiitos

[@jpa2217]

@@JamesParus voiko sen peltikiekon ottaa pois vaan

[@pipapleite]

Vivacity 125cc or 50cc? Thanks

[@JamesParus]

this is 50cc. 125 probably has no limiter.

[@MrCipherify]

lol stupid 125 with limiter go and do some research girls and scooters -_-

[@RoastedSwan]

+James Parus 125cc have limiter to

[@Josephryan1337]

Anton Eriksson :)

[@mrentremattor5772]

kiitos

[@johanzh2550]

best way to strip the threads is to use this machine for tighten the nut

[@zzpote2784]

just a question about how to unscrew the bolt at the center of the variator ? It is a14 mm bolt and when I try to unscrew everything turns. I see you use an electric wrench, but how to unscrew it with just a manual device ? thanks

[@JamesParus]

you can sometimes hold it with big screw driver, but its easy to destroy aluminium fins.

[@zzpote2784]

+James Parus ok thanks for the answer I bet the best is to use a device installed in the spark plug orifice to block the piston. Last question ; you said the 3 washers could be completed by extra washers, but you totally get rid of the plate and washers attached with the 3 bolts (7 mm) is there any risk the small cylinders may escape from their location ? Regards.

[@JamesParus]

+ZZ POTE there is no chance to escape as they are under that plate. visible at 3:10.

[@zzpote2784]

+James Parus ok thanks ! it seems obvious now !!! I just have to do the job on my son's bike. maybe next week-end... thanks a bunch for your availability