Secondary ignition analysis using Pico 7 Autonerdz link for your scope needs autonerdz.com/?wpam_id=2
Пікірлер: 46
@MarzNet2564 күн бұрын
Excellent demonstration. There goes the money they saved buying aftermarket parts for critical components, not to mention the hassle.
@CartersDiagnostics4 күн бұрын
Exactly 💯
@ryan.mullen2 ай бұрын
This is such a great video.
@CartersDiagnostics2 ай бұрын
💯🙏
@hometownautorepair31214 ай бұрын
I just got a pico about 6 months ago, looking forward to learning more, glad i found ya
@CartersDiagnostics4 ай бұрын
Congratulations on the scope! Glad your here.
@DJ-tn7vj9 ай бұрын
Solid work as usual Mr Carter. We slowly getting there. The P7 crossover
@CartersDiagnostics9 ай бұрын
Yeah, Im slow to change.
@peterhamilton27159 ай бұрын
Great technique and explanation. Look forward to these videos coming out .
@CartersDiagnostics9 ай бұрын
Awesome, thank you!
@tedgtfan7 ай бұрын
Thanks for the education. Picked up some valuable learning from this one.
@CartersDiagnostics7 ай бұрын
Good deal.
@chrisingram72779 ай бұрын
Awesome case study and well presented, thanks👍
@CartersDiagnostics9 ай бұрын
Thanks for tuning in!
@Jamie_44442 ай бұрын
Excellent content as always. Thank you😎
@CartersDiagnostics2 ай бұрын
O yea!
@JeffinTD5 ай бұрын
That was an excellent diagnosis and awesome video.
@CartersDiagnostics5 ай бұрын
Thank you.
@elitemobileautoelectric77825 ай бұрын
Thank you for sharing very informative information!
@CartersDiagnostics5 ай бұрын
Glad you enjoyed. I appreciate the comment.
@baxrok2.9 ай бұрын
Well done!
@CartersDiagnostics9 ай бұрын
💯
@glenforehand9 ай бұрын
Cool channel you got going!
@CartersDiagnostics9 ай бұрын
Appreciate that. Welcome aboard!
@ford033699 ай бұрын
Awesome
@ablackformula9 ай бұрын
Awesome video! Once cylinder 3 was verified as the misfire, any reason you didn't do any engine mechanical/relative compression check? Perhaps it was just an easier next step to put the ignition probe on top of a coil?
@CartersDiagnostics9 ай бұрын
I did a relative compression test, just didn't film it. It was fine so I proceeded with the ignition testing.
@vickenkaragozian20419 ай бұрын
Thats awesome. How do u like the autonerdz support? Very nice clean ignition waveform on pico scope.
@CartersDiagnostics9 ай бұрын
The support is great, I've been dealing with Autonerdz for over 10 years. I would not promote them if they were just average.
@vickenkaragozian20419 ай бұрын
@@CartersDiagnostics ok thank u very much. Planning to buy the pico scope. 👍
@CartersDiagnostics9 ай бұрын
That's great. Autonerdz has alot to offer than just the scope. Lots of support including the forum, monthly zoom style training, access to the cloud for cool custom probes and apps and more. The membership is included with a Pico kit and never needs renewal.
@vickenkaragozian20419 ай бұрын
@@CartersDiagnostics awesome. Thanks for the information
@eklazhward47396 ай бұрын
impressive how detailed is your diagnostic way...but, @16:15 how it work, that misfire on 3rd cyl affect to spark time from 1st cyl ? Why You not backprobe coil on 3rd cylinder, as you suspect that 3rd cyl misfire ?
@CartersDiagnostics6 ай бұрын
Thanks for the comment. I checked the time stamp you provided. I was on #3 cylinder ignition. Now at the beginning of the video I was on #1 until I properly identified the problem was on #3.
@eklazhward47396 ай бұрын
@@CartersDiagnostics So sorry, my bad
@t250r9 ай бұрын
Great case study! Do you locate your problem cylinder the same way with a 6 or 8 cylinder. I've read you look at the 360 mark, then one to the left to find your exhaust stroke. It gets confusing to me with the 6 or 8 cylinder.
@CartersDiagnostics9 ай бұрын
Great question. Rule of thumb is on a 6 cylinder go two to the left of 360 for exhaust.... on a 8 cylinder go 3 to the left. that should be your sync cylinder's exhaust stroke. Its always good to experiment on known good..and create misfire's and test the theory with your equipment before a problem child hits your bay.
@wzthonda80139 ай бұрын
good video thanks. when encounter engine misfire that obd 2 mode 6 will show which cylinder more false count than other .do you think pulse sensor is best way find what cylinder misfire? do you have coupon code for autonerdz? think about pico scope to buy, but kind expensive special work for dealer they do'nt pay check out time specially for warranty repair.
@CartersDiagnostics9 ай бұрын
The pulse sensor is best for me, simple to set up and not very intrusive, it just takes time and practice to understand the wave. My Autonerdz link takes you to the website, the picoscope kits are already discounted, vs buying everything individually and I think free shipping for USA. But feel free to call them or email them, its very possible a deal can be made.
@johnhill36449 ай бұрын
heard yesterday that our dealership will be getting the pico 4425a. which software will run 6 or 7. id like to get a head start playing
@CartersDiagnostics9 ай бұрын
CONGRATULATIONS! Iuse the latest P6 and a early access version of P7. Both can be used on the same computer. Both can be found under the training and support tab. Just click on the autonerdz link in my videos. Also ask the management to order your stuff threw my link. It helps me keep things going. THANKS.
@robertofkennedy9 ай бұрын
The top spring on the left looks like it's a different diameter
@CartersDiagnostics9 ай бұрын
Aftermarket stuff, anything is possible.
@shermanbird32489 ай бұрын
"Jumping out early"? Huh?
@nickayivor84329 ай бұрын
Brilliant video 👍 SHREWD Carter's Diagnostics Enjoy your weekend with all your family around you, Carter's Diagnostics ASTUTE Carter's Diagnostics From Nick Ayivor from London England UK 🇬🇧 ⏰️ 06:52am Good Morning 🙏 🌄