Behringer XENYX 802 Mixer Setup

[@pigeonistvideos]

Thanks! Those are audio cables from Hosa. One end is 1/4 TRS into the H4n and the other end is just RCA plug to the monitor out of the mixer. I use it to record my mixes so I don't have to record on the computer.

[@CrankCase08]

I've been using one of these for some time now but have realised the audio is not good enough for quality vocal recording, but it's good enough for live work. The 6.5mm jack sockets seem to be pretty cheap too because the connections become unstable, likely due to fatigue of the contacts, and the preamps get too noisy when turned up. Consequently, I'm now going to replace it with one of the Focusrite Scarlett range, I just haven't decided which one yet.

[@1961woodstock]

I just used this unit a week ago for a wedding gig, not that i have that much experience using it and it was right out of the box so no time to figure it out! The microphone i used we could not really get any volume out of it, and now i see what you just showed , TURN IT UP IN THAT LINE OF SWITCHES, i feel like an idiot now lol lol But just learned something , thanks much for the video.

[@pigeonistvideos]

I have an external USB sound card which I output to the mixer. The mixer does not connect to the computer digitally in anyway. You can consider using the headphone out 3.5 jack of your computer connect it to the 1/4 inch input of the mixer. You'll need a special cable.

[@ridarecords]

not bad homie this helped me decide this works i appreciate this vid.

[@pigeonistvideos]

Yes you can output two channels to mains and 2 channels to sub but I'm not sure about the volume control. I don't think you can do it since I think the master volume will control the monitor volume.

[@pigeonistvideos]

Dual 1/4" TSR cable from the MPC rear output to the L/R input on the mixer.

[@pigeonistvideos]

Mine came with everything I needed it for it including the power cable.

[@saeedsiddiki2007]

excellent setup - what are those cables going into the H4N

[@lisadesign19]

Great job 👍thanks

[@pigeonistvideos]

Thanks. You do not need an external recorder like the Zoom. You can just record within your computer like most do. I just do it this way to save on system resources but it's not the primary reason I have the Zoom.

[@marcolopez678]

MAXER 🎤🎤🎶🎵

[@pigeonistvideos]

@DJSHAZ2012 I'm using a RCA to dual 1/4" TRS cable from Hosa.

[@Daniel13Kim]

@pigeonistvideos Hey man, I loved your video. I' am planning to buy this mixer too. I do have one question though. Is there an on and off switch button for the Behringer XENYX 802? If not, then if you want to turn it off, is plugging out the power source the only option? Because from what I've heard plugging out the power source to turn something off damages the product. Please respond back ASAP! Thanks!

[@machoje]

hello. i have bought a behringer kenyx 802, and i wanna ask you if he has also some echo effects on microphone ..thank you very much

[@PrathameshKshirsagar]

Can you tell me plz how to use delay reverb in this mixer

[@pigeonistvideos]

I'm using a RCA to dual 1/4" TRS cable for the audio.

[@riosproductions3930]

You can use a USB interface that Behringer also sells to hook this guy up to a computer. I just bought the Behringer Q802USB which comes with the USB interface built in. That is also an option. I am using mine for podcasting and plan to use the FX send slot for live phone calls using iRig. I'll be posting when I'm set up if anyone is interested.

[@drodriguez4879]

Just got me one! Luv it! !!!

[@DJSephEntertainment]

Is it possible to hook up main speakers and two powered subwoofers and have independent volume knobs or sliders for each?

[@TheBashada]

do I need to buy that Zoom recorder or can I record my Numark mixtrack pro mixes via this mixer and audacity. great vid btw

[@zsoltnagy8398]

How can I have that Eco voice effect like a singer?

[@johnnydwicked]

Does your Xenoyx 802 get hot on the underside? Is that normal?

[@DJSHAZ2012]

what kind of wire did you have to connect the Mixtrack Pro too the Behringer mixer?

[@pigeonistvideos]

Yes the H4N is setup to record from the line level output of the mixer.

[@l.a.x4338]

Hey is there a way to connect more than 2 speakers????

[@pigeonistvideos]

Yes, XLR will fit. The unit also has phantom power.

[@anlelmastas6201]

Hello. Thank you for this video it is really good and than I have a question. What is your soundcard or audio interface I am really curious about it I watched video but I couldn't see :)

[@edpritchard6897]

THANKS FOR SHARING..GODD LUCK....

[@dorianwilson4559]

Never think what you produce is crappy. I did the same thing to a couple of my tracks, and people loved it. A few wanted to buy the tracks. So, let me hear some music you've created sir...

[@fazebronco3760]

could i use those rca connections to run sound to another speaker i have because im gonna run a sub and this speaker but this top speaker is running rca

[@Raldo_05]

hello, can you help me when I record their is humm or buzz the more gain i put the more buzz I heard ...is there something wrong with the connection?

[@humanbeingfromearth]

Thank you for this video. Im getting one tomorrow, and wanted to read up. This thing has like six inputs if you do it right, and five outputs! depending on what u use the fx channel for. this other bloke used it to send individual channels out, using the fx gain knob or whateva its called.

[@JimboDean9]

so is something like a ux1 useless with this kind of mixer? or is there anyway i can hook it up and use the extra mic and guitar jacks? im not sure how well this brand would work out for me since im looking for nicer mic preamps for clean vocal and acoustic sounds..also wouldnt know how to set it up to record with ableton..

[@sanjayagnesh6854]

behringer with sound card kanha se kharida ja sakata h plz hume guide kare ye kou se softwere me run karta h

[@riosproductions3930]

There is no off switch on the 802. There is an aux on the power supply no info on what this does that I can find. If you Break down your equipment properly then you should not have any issues damaging this product. Also one quick tip if you have a problem with these small mixers not having any on / off switch: Buy a surge protector. You should be using one for your setup anyway. Use that to cut power. Cheers!

[@107SONIDERO]

how to connect a VMS4 controller wit the Behringer XENYX 802 and used a microphon ?

[@danishthomas1981]

Hi, How can I connect Behringer XENYX 802 Mixer to the Sony Home theatre system?

[@Graid7]

how many channels are on it?

[@BogdanSerban]

Can you tell me if the FX send is mono or stereo? I can't understand from the user manual. I need to send a stereo out to a tape machine, which goes straight back to the sound card, but then I need two other outputs, one for the monitors and one for the bigger speakers, and two stereo inputs, from the main PC and from the laptop/phone/turntable etc.

[@pigeonistvideos]

The FX send/output is mono. The FX return/input is stereo.

[@BogdanSerban]

Thanks!

[@tdotbdot2012]

Hey man how do you hook up your mixtrack pro to mixer?

[@cashvisionfilms903]

wondering can i hook a compressor up to this if so where do i plug it in

[@pusher1012000]

can u have a turntable on the going to the mpc?

[@xdbrain]

how do you hook up your mpc to your mixer?

[@ZWATER1]

thanks bro

[@DJTitoTheFuzz]

awesome gear, exept for the crappy boombox lol, im thinking about getting this for mobile djing uses, i have a traktor kontrol s2

[@jayextreme6350]

Hey dude We'res your video on setting the 802 up for Skype

[@pusher1012000]

how much do they go for

[@asmith5881]

what cord do use to connect the mixer with the mpc ???

[@djkemydancommandoforce8947]

can u set it n use the numark to use for your gain n control all gain

[@AtrioxIsBanished]

how is your dj controller connected, which input on the mixer is it plugged into?

[@pigeonistvideos]

The MixtrackPro is connected to channels 3/4 via RCA jacks. Go to time 3:25 on the video.

[@keithgray8093]

Pigeonist What Cords do you need or what do you need too hook it up usb mode so i can hook it up to my laptop and use it in fl studio

[@pigeonistvideos]

It's not USB compatible. It's a very basic mixer.

[@MrTrippple]

how do i hook it up to computer?

[@daniellelite3080]

How do I use the fx in the console?

[@pigeonistvideos]

@ridarecords Thank you!

[@ilyazhitomirskiy9218]

Hello there! I plugged in my Yamaha CM-500 headset into my Behringer XENYX Q802USB mixer, plugged the mixer into the computer, and tried speaking into the microphone. For some odd reason, my speech into my headphones is slower than the rate at which I am actually saying it. How do I fix this error? Thank you very much!

[@arncj18]

newbie here: since this is not USBversion , what type of cable do you connect this to your Laptop/Pc with? I just need it to connect my xlr mic, beyer headphones and speakers via jack to this , will I be able to?

[@pigeonistvideos]

You can output from your computer headphone into the mixer aux in using 3.5 jack to RCA cable. If you use an XLR mic it won't go route back to the computer. You can try but there will probably be an echo.

[@arncj18]

aha and the RCA end needs to be 1/4" right? and so the xlr mic wont work properly?

[@pigeonistvideos]

RCA jacks look like the ones in TVs. You can try using the 1/4 TRS jacks as well. The mic can be routed to a digital recorder but routing it back to the computer will cause a loop so you might hear your voice with an echo. Get a 2nd hand audio interface if you want better audio/computer connectivity under $100.

[@Gsweetwyne]

Hey I've had this issue forever(like 5+ years) and never worried about it until now. SO... I have my two monitors plugged into the main out, it's basic, the right speaker is plugged in to the right and the left is plugged into the left. HERE'S THE PROBLEM... Whenever there is a pan to the right it's very faint. anything that's panned to the left works perfectly BUT the right is barely able to be heard. What do you think the issue could be?

[@pigeonistvideos]

Don't take offense if I state the obvious. I don't know how thorough your troubleshooting has been at this point. I'm just gonna list things I would check. 1. Check PAN level at input source 2. Check PAN level at mixer input 3. Check levels of the the weak monitor if powered 4. Check levels of the the weak monitor at amp if applicable 5. Check your wiring and plugs I would also flip the L/R to see if the problem flips or stays. I'm ready to move on from this mixer. So I'll be getting rid of it to get more channels and built in effects.

[@darrionsmith5230]

How do I decide what speakers to get

[@pigeonistvideos]

1. Budget 2. Listen to the speakers personally at the store 3. KZbin reviews 4. Have a clear understanding of what the speakers are for (studio or party) I'm sure there are other things to consider but start with that.

[@marcolopez678]

MAXER 🎤🎤

[@davidfriddy5824]

How can I setup the FX funk. on the Q802 USB?

[@pigeonistvideos]

It really is.

[@ChristianPanero]

So I can have 2-3 inputs and than I can mix them, but can I use the main output with two monitors and also use the "ctrl room" for another monitor? If I connect also the "ctrl room", the signal level will be the same or not? I hope it will be louder, but I don't know. Could you tell me it, please? (sorry for my bad english lol) Thanks.

[@pigeonistvideos]

CTRL room (L/R) has it's own volume control just like the main outs (L/R).

[@ridarecords]

@pigeonistvideos yup keep with it lol very good review if i could rate id give 5/5

[@Demon-Knight]

I have one of those mixers too I don't think its very good the most effective thing about it was the volume in my opinion. I want one with effects and stuff on it I think that would be a better choice for me.

[@myway936]

thank you

[@omaralvarez9764]

Hi, when I connect my phone on the rca inputs my level goes pretty high and clips, its so embarrassing in parties, I set the volume on my phone to max could that be the cause ? I use my phone to play You tube videos, and mp3s, from it, thanks.

[@Z0mbieHunterMan]

Yes that is the cause. Glad to help 6 years later

[@omaralvarez9764]

@@Z0mbieHunterMan its been 6 six years, holy crap lol. Still got it thanks for the reply.

[@maryannjuralbar4126]

Hi can you help me?

[@JulianCampbellPPV]

Hello, will these cords (www.amazon.com/Hosa-CMP159-Stereo-Breakout-10-Feet/dp/B005HGM1D6/ref=pd_bxgy_MI_img_y) work with this mixer? They fit in perfectly but they don't seem to be working. I cant get my laptop to recognize my c2 behringer condenser microphone. My friend was once. able to make it so the laptop was picking up sound coming through the microphone but it was very bad quality Should I get different cords? I'm looking for ones that can go into a laptop

[@SteveScullyMusic]

did you turn on phantom power on the mixer after you plugged the mic in ?

[@classikunity1358]

thanks

[@rickysantillas1008]

Cool

[@turOloks1]

I GOT A BIG QUESTION

[@pigeonistvideos]

Ok

[@rodolfobaliga7577]

how can i buy a cheap, good quality mixer with a good bass & treble output. thanks and more power to anyone who can answer this query.

[@hausiksf]

We've got some wonderful deep house for you to check out: soulful vocals, a round & funky bass line, and punchy percussive elements! kzbin.info/www/bejne/sJLJXpSih9dnetk

[@prizmapex]

You said you wanted to give your two cents worth of input, how come when you put your two cents in you only get a penny for your thoughts, your losing money there.

[@ggpucky85]

nice please check my studio leave any comment thanks

[@kevinsavage7322]

where can I connect my mixer to the laptop with a focusrite solo audio interface? Thank you.

[@mikey_dubz]

Mixer output to focusrite input to laptop usb and you’re good to go

[@walidbenallel5514]

hi, 1 question the instrumental enter with my voice when o record, Why???

[@pigeonistvideos]

The instrumental goes to the main output with your voice. The tracks can not be separated for the output. Listen to the instrumental from another source like your mobile phone with headphones. Do not put your instrumental in the mixer.

[@pauldavison3882]

Hi Walid! Connect your sound card/audio interface's output to the mixer's 2-track in, and the mixer's 2-track out to your sound card/audio interface's input. Also connect a mic for recording your voice (obvious) and headphones for monitoring. Push down the 2-TR TO CTRL ROOM button, and make sure the 2-TR TO MIX button is up (very important). This configuration sends your "instrumental" to your headphones while your voice goes down one channel, onto the stereo bus (alone) and out through the mixer's 2-track out. Hope this helps, and good luck with your recordings!

[@lisadesign19]

Thanks