Piping Isometric Drawings Explained for Beginners.

[@audiobook-s]

Good job thanks again for sharing this video

[@Funnyman-videoss]

Like videos helps us fo improve our piping skills

[@audiobook-s]

please continue to share these videos

[@abdulhesimov9585]

Very good job

[@nenehacxanm5364]

Good job

[@nikosaliyev9666]

Good job for pipefitters

[@qurbanqurbanli9242]

Very good exclent

[@cosqunsalamnov6738]

Veryi gud 👍👍👍

[@celalmutellimov5919]

Good piping video,thanks for sharing

[@rovshenrovshen9341]

Nice informative video,perfect

[@ramilnovruzov2955]

Could you please share video about 3d model pipe isometric

[@rupangchannel888]

Thank you 🙏

[@Piping-engineer]

You’re welcome 😊

[@blakewilliams6613]

so a 45 degree is an up and cunfuses every thing. . . . . . figure some thing else for a 45 degree or find a better eplain for the 45 deg not to confused with the UP. . .

[@Piping-engineer]

Many thanks for watching and comments, my friend. We will take your advice into consideration in our future videos.

[@mauriciogjomemo474]

the same, i dont get the 45 degree angle , something must be wrong

[@rajuparapati3638]

Exlent explainess

[@Piping-engineer]

Thaks for watching and comment

[@deanmanuel9560]

Very good please show more in English.

[@Piping-engineer]

Thanks for watching, Yes, will continue videos in English

[@aliflankes8259]

Good drawing but sould be more descriptions

[@celiajuarez4376]

Can you show a isometric cube drawing

[@XtremeVeh]

Do you have a tutorial on how to draw this on sketchup .Thanks

[@Piping-engineer]

Yes, If you watch our other videos you can see that,l am using Sketchup,Bandicam,clip champ and Canva

[@scorpiontetteh-kf2ic]

Thanks

[@XtremeVeh]

What softawre did you use to draw it on paper

[@Piping-engineer]

Sketchup

[@nelsonconstantino3856]

𝒀𝒆𝒂𝒉 𝒘𝒓𝒐𝒏𝒈

[@waleedyoussef5956]

من فضلك يا هندسة، elevation هو منسوب مركز الماسورة او الراسم العلوى او الراسم السفلى تحياتى واحترامي

[@Piping-engineer]

مرحبا سيدي، شكرا جزيلا على المشاهدة وأفكارك القيمة

[@Baiano7589]

2 curva de 45° ? Como assim?

[@arturj.8804]

Your wire bending is wrong? Two last angles are wrong. Your bending from north to east should be 90 degrees, your wire is clearly 45ish degrees. And then you should go straight up, also 90 degrees. Its a shame bc your explenation was correct but the wire bending makes it very confusing

[@Piping-engineer]

Many thanks for watching and comments, my friend. You are absolutely right. After watching your video several times, I was able to understand what you said. Unfortunately, it is not possible to correct this in this video. We will definitely be more careful in our future videos.

[@JhongBaguio-h8e]

Yes he is mistake.not correct.

[@gilcineyteles]

O arame tá virado na coordenada ,mas porém fora de esquadro

[@Piping-engineer]

Eu fiz uma nova versão deste vídeo, por favor assista também kzbin.info/www/bejne/aKXcY614e5V4iJo

[@sergioxmc1]

software to drawing?

[@Piping-engineer]

HI, are different software, sketchup

[@sergioxmc1]

Sketchup? 😮😮

[@RicardoDelasAlas-w6n]

Is that correct?

[@King_Ingsley]

The wire bending is wrong

[@rahimpakottik2794]

good

[@Piping-engineer]

Thanks for comments

[@luismaldonado4193]

Esta mal hecha las lineas, linea horizontal no tiene elevacion, linea vertical si

[@Piping-engineer]

Gracias por ver y comentar, tendremos cuidado.

[@scorpiontetteh-kf2ic]

I want to subscribe

[@Piping-engineer]

Thanks for watching

[@louiedeesantiago1673]

Yes that's wrong😂

[@Piping-engineer]

I don't agree with you

[@SR-os1qt]

@@louiedeesantiago1673 this was everything good till he take the wire to bend

[@klaustukas5505]

Its wrong😑

[@Piping-engineer]

Correct! Again watch, please

[@MrGalaxyguy]

Correct explaination and Wrong implementation

[@avinashgadagi3706]

It's wrong

[@khanjone2052]

It's wrong information

[@babagulmammadov416]

Good job