PIR SENSOR WITHOUT ARDUINO

Hi in this video i will show you how to use pir motion without arduino.
Componets required
------------------------------------------------
1)pir sensor - amzn.to/3rVmHcO
2)bc 547 npn transistor - amzn.to/3BrzAyC
3)5v relay - amzn.to/357sK4Y
4)1n 4007 diode - amzn.to/34MQ34s
------------------------------------------------
Circuit diagram : bit.ly/2yvt4u8
------------------------------------------------
Song: MBB - Clouds (Vlog No Copyright Music)
Music provided by Vlog No Copyright Music.
Video Link: • MBB - Clouds (Vlog No ...
------------------------------------------------
thanks for watching
========================
#Electroretro #pirsensor #electronicsproject

[@ElectroRetro]

Circuit diagram : bit.ly/2yvt4u8

[@jackson-aka2gs749]

tested over and over. this works perfectly, thank you.

[@ElectroRetro]

👍

[@luizsimplicio1783]

esse pir e muito legal gostei ja fiz 4 sensor de presenca e´10

[@richard8241]

Thanks good video. Could I hook this up to a 12v horn for an alarm instead of the light ? Would I need anything bigger like the diode or transistor ?

[@ElectroRetro]

Yes you can, Input voltage for pir is +5V for typical applications. Can range from 4.5V- 12V

[@richard8241]

@@ElectroRetro Thank you ! Subscribed ! ;)

[@smash461986]

Hello. This worked great for the LED strip on the stairs. I've had someone message me so they can do the same so thanks for the video and responses. Currently I use a smart plug to tell the strip to only come on at night but if you were to add a light sensor and get rid of the smart plug, how would you wire it?

[@ElectroRetro]

If you open that white cover on PIR sensor you can see a connection point marked RL, You can solder a LDR (Light Dependent Resistor) on that to sense motion only at night time.

[@smash461986]

@@ElectroRetro Wow it's that easy!? Very helpful thank you.

[@ElectroRetro]

👍🏼

[@haranadh_vizag]

Hi...Electro Retro .. really great work 👏👏 can I have circuit with out any relay ..I need simple Hi 9v battery with 4 led PCB design PDF. Ready to itch

[@ElectroRetro]

You can simply replace the diode and relay with leds

[@manlikezakaado6135]

where did you plug the 12V input LED wire

[@kiranshashiny]

Im trying to connect a 5V DC motor instead of the relay,

[@ElectroRetro]

Yes you can connect it

[@leon9357]

Nice. Just two questions: 1) Can I use 12V LED strip 5 meter or long? 2) I want to use two PIR sensor for my automatic stair case light.So how to do that?

[@ElectroRetro]

Yes, you can use

[@leon9357]

@@ElectroRetro Thank you. But how to use two PIR Sensors for the stair?

[@ElectroRetro]

Connect two pir sensors in parallel. Vcc to vcc, signal to signal, gnd to gnd.

[@leon9357]

@@ElectroRetro Thanks.

[@FlightSim2703]

It's cool, but what is the light for if this light comes on in daylight? Could you figure light to comes on after dusk ?

[@ElectroRetro]

If you open that white cover on PIR sensor you can see a connection point marked RL, You can solder a LDR (Light Dependent Resistor) on that to sense motion only at night time.

[@FlightSim2703]

@@ElectroRetro awesome, will you sometime load a video, for how you do it , thanks 🥰♥️👍👍👍

[@ElectroRetro]

Yeah.

[@naveendsouza2137]

This is perfect but i want to use 12v for both pir and led what needs to be changed

[@ElectroRetro]

Use 12v relay

[@naveendsouza2137]

What about the transistor and diode value? Will it be the same... Thank you for the quick reply. Im not from electronic background so can you please tell me

[@ElectroRetro]

Same

[@ersomesher]

How to connect a 12V LED strip light directly to the sensor without using any resistor or transistor or a relay. The LED strip light will be powered by 12V 5A driver. The setup will be mounted underneath the kitchen platform. The LED strip light should turn ON when the drawer is opened.

[@ElectroRetro]

Without transistor or relay not possible.

[@netsurfer2975]

I have relay modules instead of the stand alone relay. Can I make this work?

[@ElectroRetro]

Yes

[@jayrcabales6463]

Can you show a circuit diagram with the led on it. I dont know how to make circuit diagram

[@ElectroRetro]

Just replace relay with a led. And make sure to add a resistor

[@racelikepro]

Hi brother I want to use pir to control my magnetic door lock... Will the same circuit work where the bulb is replaced with the magnetic door lock

[@ElectroRetro]

Everything is same just replace bulb with lock

[@racelikepro]

@@ElectroRetro thanks for the response will do n share my feedback

[@ashutoshkhire3604]

hello sir did u connect the brown and the red wire to another battery of 5 volts

[@ElectroRetro]

Yes

[@ashutoshkhire3604]

thank u sir for the very quick reply i will go for it

[@ashutoshkhire3604]

@@ElectroRetro and by the way we need to use npn type bc 547 transistor right

[@ElectroRetro]

Yes, use npn transistor.

[@ersomesher]

How to connect a 12V LED strip light directly to the sensor without using any resistor or transistor or a relay. The LED strip light will be powered by 12V 5A driver. The setup will be mounted underneath the kitchen platform. The LED strip light should turn ON when the drawer is opened. Why are transistor and resistor mandatory? What would happen if remove them and connect LED strip light directly? Reposting as I can't find my previous same comment.

[@ElectroRetro]

Can't connect 12v load directly to pir sensor. You need a relay or mosfet.

[@ersomesher]

@@ElectroRetro What would happen if neither of these are used and the strip light is directly connected. Will the light get damaged or the sensor? Or nothing will be damaged and the LED won't glow?

[@ElectroRetro]

@ersomesher There is a good chance for sensor damage.

[@ersomesher]

@@ElectroRetro Thanks for responding. If you have spare sensor and some time, request your kind hello to try that configuration and confirm if it's working or not. I don't have spares, hence the request. Thanks.

[@ElectroRetro]

As I said earlier it's not possible to directly connect 12v load to pir sensor.

[@suyashbalang]

Can I use this circuit in direct sunlight. Will it work or it gives an malfunction…???

[@ElectroRetro]

Maybe it Will work but sometimes have a false trigger

[@nakhla3]

Is it safe to use the diode and bc547 with ordinary 220 volt ? Please answer quickly I am doing it right now

[@ElectroRetro]

Bc547 and pir sensor must be powered with 5v. You can connect 220v to the relay contact pins.

[@diane1993]

While the motion detected, relay on multiple times ...giving a continous sound and the light is on ....can give suggestion for thz trouble shoot

[@ElectroRetro]

Check the voltage on relay coil pins.

[@diane1993]

The voltage fluctuates

[@ElectroRetro]

Most likely that's the problem. Check your power supply and connections.

[@ccoinchris1905]

Any way you can show a picture of the whole system, in the video i cant see where the wire are going on the table, battery source

[@veronicajuarez7829]

Can this be used for a 5v led strip?

[@ElectroRetro]

Yes

[@devilpulsar]

Red brown wire kis chiz ke hai please reply

[@ElectroRetro]

Red is positive 5v and brown is negative

[@survivor351]

Hi, nice project, can we use more pir sensors with same circuit (for different angles scan)

[@ElectroRetro]

Yes, use diode on output pin.

[@survivor351]

@@ElectroRetro thanks, did i understand right? Vcc and ground pins same connect to 5v input, outputs to diodes on pin, not use another bc547

[@ElectroRetro]

Example:- drive.google.com/file/d/1fASavSSkePmwn7HxRfWk1D5bIP_22512/view?usp=drivesdk

[@ElectroRetro]

Everything is same just add diodes on output pins.

[@survivor351]

@@ElectroRetro thank u so much

[@SanjeevKumar-dx8gt]

sir, I did everything as per this video. but my bulb is always turned ON. I checked my PIR and the voltage is coming properly, my relay is in proper connection (NO)... what are the possible problems?

[@ElectroRetro]

Adjust you pir sensor delay to minimum.

[@SanjeevKumar-dx8gt]

@@ElectroRetro I kept it brother but still it is the same issue.

[@ElectroRetro]

You need to check if the voltage on the PIR output switches. Use a multimeter to measure the voltage between OUT and GND.

[@SanjeevKumar-dx8gt]

@@ElectroRetro I did and did not change at all. means it remained the same value.. Should i need to change PIR and check again? also, NPN or PNP version matters?

[@ElectroRetro]

Change your pir, make sure you are using npn transistor.

[@ianjaspercanda8414]

New subscriber here

[@ElectroRetro]

Thank you so much.

[@Martin-dw4eo]

Me too. I just subscribed.

[@dj_sorra8605]

Can I feed the sensor with 5v and the LED (5v) also with 5v?

[@ElectroRetro]

Yes

[@smash461986]

Hello. I'm using a 12v led with 12v relay. How do I attach the positive and negative 12v to both the led strip and pir sensor? Thanks

[@ElectroRetro]

Connect supply's positive pin to the relay's common pin and connect led's positive to relay's NO (normally open) pin.

[@smash461986]

@@ElectroRetro thanks for the rapid response. I shall give it a go.

[@smash461986]

Hello I'm not getting anything from the led strip. It's only 3 leds but is a 1a supply too low? The relay is rated at 10a. Does the negative of the 12v supply go to gnd on the PIR? I'm basically trying to do your setup but without an additional 5v for the PIR but it's throwing me off completely.

[@ElectroRetro]

Negative and positive must be connected to the PIR sensor.

[@smash461986]

@@ElectroRetro hello. Brilliant there is life. There's a clicksound when the motion detector activates. I think it's the relay. Is this normal? Thanks for the help so far BTW, I was ready to give up.

[@ashutoshkhire3604]

there is no compulsion like where we need to connect the anode and the cathode of the 1n4007 diode to the relay right ???????????

[@ElectroRetro]

Diode cathode should be connected to positive.

[@ashutoshkhire3604]

@@ElectroRetro ok thanx and u didn't need to adjust the distance and time did u ?

[@ElectroRetro]

You can adjust delay and distance according to your application

[@ashutoshkhire3604]

@@ElectroRetro ok thanx

[@prathmeshchopade2213]

Sir how should I increase ontime

[@ElectroRetro]

Adjust left potentiometer clockwise to increase delay.

[@ArbazKhan-bg2sb]

Can i use this for tubelight?

[@ElectroRetro]

Yes

[@ArbazKhan-bg2sb]

@@ElectroRetro hi, if i want to keep the light always on then can i add an on/off switch as well?

[@ElectroRetro]

You can use a two way switch.

[@konkani8978]

Can we use multiple pir sensors in parallel?

[@ElectroRetro]

Yes you can use

[@konkani8978]

Thanks sir 👍

[@jeremiahlaman2010]

I follow the connection . Why is it. Turning on and off without sensing the sensor?

[@jeremiahlaman2010]

Please help

[@ElectroRetro]

When the PIR sensor turned on, it will automatically turn on and turn off after 30 sec.

[@auntijinamastey]

Sir, my pir sensor always stays on. What is the problem.

[@ElectroRetro]

May be your sensor is faulty

[@jindeva397]

Can i do this without the relay?

[@ElectroRetro]

Yes

[@daybreaklover2999]

Is the transistor PNP or NPN?

[@ElectroRetro]

Npn

[@shanushah9690]

can i use 547 to 548 bc

[@ElectroRetro]

Yes

[@pranshubahuguna4486]

What will happen if we don't use transistors

[@ElectroRetro]

It won't work

[@aceboyz9169]

How about IR sensor

[@aldemjohne.salvadora8785]

can i use 12v DC?

[@ElectroRetro]

Use 12v relay

[@aldemjohne.salvadora8785]

@@ElectroRetro what if a 9v DV BATTERY?

[@ElectroRetro]

Use 9v relay

[@dhirajmishra6583]

Can i use BC548

[@ElectroRetro]

Yes you can

[@dhirajmishra6583]

@@ElectroRetro thanks sir

[@mirzasikenderzaib1285]

Sir can we use without transistor

[@thusharpa2924]

Sorry im late

[@ElectroRetro]

Thanks for watching

[@suraidasuraidaju4181]

what type of glue u use

[@ElectroRetro]

I didn't use glue in this video

[@rithminipehansa3562]

How to add LDR to this circuit ?

[@ElectroRetro]

If you open that white cover on PIR sensor you can see a connection point marked RL, You can solder a LDR (Light Dependent Resistor) on that to sense motion only at night time.

[@rithminipehansa3562]

@@ElectroRetro thank you ✨️💜️

[@sakukumee8346]

can12 v input

[@ElectroRetro]

5v is recommended

[@chakrawartikumar1335]

can I use 12v Relay

[@ElectroRetro]

Yes

[@pakpii4883]

Komponen belinya dmn toko apa bos

[@ElectroRetro]

?

[@mohamednifras1990]

Bro ethumari nan bathroomle set pnnina bro anal nan niddu pattan off avuthu bro nan asajja on avuthu asayaddi off avuthu bro

[@ElectroRetro]

Can you pls tell me in English

[@hamzabro06]

Range?

[@ElectroRetro]

Upto 7meter

[@amnafatima163]

can i add 2 motors so that i can make a robot

[@ElectroRetro]

Yes

[@amnafatima163]

@@ElectroRetro and do you have any guidelines for making it

[@ElectroRetro]

If you are trying to turn on two motors using one pir sensor. Just connect two motors in parallel

[@amnafatima163]

@@ElectroRetro okay

[@athuldev5307]

🤓

[@tanishqpraksh5753]

What kind of wire is used?

[@ElectroRetro]

Hookup wire

[@teddyyusman8571]

Can i use 12v relay?

[@ElectroRetro]

Yes