@@curits8260 This module support 15Ah battery

@@ElectroRetro thank you

It's possible to increase Max input voltage by replacing mosfets, diodes,input capacitors, input voltage dividers and some editing in code. But I don't recommend it, because it's not safe and I didnt test this mppt with more than 90V.

@@ElectroRetro thank you

At 11:15 you can see I use a module to supply the mosfet drivers. I used a boost converter here and connected it's input to +12v rail.

@@ElectroRetro ok its isolated ?

@@smartups1 yes

@@jerrysmt2959 No

Yes

No internet needed. Connect with mac address.

Can't connect 12v load directly to pir sensor. You need a relay or mosfet.

@@ElectroRetro What would happen if neither of these are used and the strip light is directly connected. Will the light get damaged or the sensor? Or nothing will be damaged and the LED won't glow?

@ersomesher There is a good chance for sensor damage.

@@ElectroRetro Thanks for responding. If you have spare sensor and some time, request your kind hello to try that configuration and confirm if it's working or not. I don't have spares, hence the request. Thanks.

As I said earlier it's not possible to directly connect 12v load to pir sensor.

No

I bought the core from digikey.

The battery life depends upon the battery capacity, You can get more than 1 month with 2000mah battery. Also the range depends upon the environment, In my tests I got almost 450 meters line of sight. So I think 100 meters will get in real life scenarios without data loss.

kzbin.info/www/bejne/nHKaaWZmaKqJh9Esi=AQzitudcxsYcnOrU

Depends upon PCB size and concentration of ferric chloride.

Ferric chloride

You can make your own. It's easy. I have given all files for free. You can also edit the PCB according to your need.

bluerobotics.com/store/sensors-cameras/sensors/bar30-sensor-r1/

No

Sir in the Cn1 S1 (2) pin connector jumper connection

@@futuresciencetechnology536 yes

NO, I have 100 A / 150 V IN / 66 V out MPPT, ESP32, onw design, own SW, it works with 90 - 98 A power all day long a few yeras and no problem. It will work at 45 - 47 *C another 30 yeras.

@@PavolFilek can i get the pcb design?

​@@PavolFilekany schematic or post about your diy mppt?

@@syarifhidayat8973 ESP32 2-phase DIY MPPT - part 125

@@syarifhidayat8973 But there is a lot of work make 2 *3 -* 4-phase 4 x 50 A MPPT, proper toroids 16 kHz - 78 kHz, N-FETS, drivers, 16-bit DACs to meause voltages, amps and temps precisely, RC snubbers or RCD clamps, SW needs to be precise and not faulty.Than communication WIFI/BT/BLE to produce HTML pages + settings with help of some 20x4 displays. Also some DC/DC cnoverters to make 12 V and 5 from 9 - 969 V battery. Then a lot of measure,ments.., testing difeerent algos, measurements of FETs and toroids and CAP temps, to have FETS at level, that afficeincy and calendar age of service will be OK:

No

Do you have flyback diode connected to the relay? If yes, then it may be electromagnetic interference from relay.

can a flyback diode fix this?

@@alifghifarii8428 it may fix.

@@ElectroRetro I've used a flyback diode and soldered it to the relay but still can't fix it, is there another solution?

Place relay further from ESP. That may work.

Sorry that feature is not added in this project. Instead, On the receiver display you can see a green dot blink every time the transmitter send a signal. if the connections are ok, It blink every 20sec apart. Transmitter goes to sleep mode for 20sec and wake up and send the signal. The sleep mode is implemented for increasing the battery backup.

Which blinking signal do you mean?

In transmitter unit code we give the MAC address of receiver unit. So there would be no interference.

If we want to change the MAC address, we change it with the coding of the transmitter. It should be changed with the coding of the receiver. My point is whether changing the coding of the transmitter will solve the problem or the coding of the receiver will also have to be changed.

@@futuresciencetechnology536 you don't have to change the receiver code. Only transmitter code needed to change. Every esp have unique MAC address.

😂You are genius thanks for you

@@futuresciencetechnology536 To get the receiver mac address you can follow this tutorial randomnerdtutorials.com/get-change-esp32-esp8266-mac-address-arduino/#:~:text=Change%20ESP32%20MAC%20Address%20(Arduino%20IDE)&text=You%20can%20set%20a%20custom,old%20and%20new%20MAC%20Address.

Please explain your problem.

@@ElectroRetro the library for Arduino IDE it's Not Working. Because this is not ZIP format Need ur arduino ide in zip format So how do I add these libraries In Arduino IDE

@@ElectroRetro and iam feeling error in library

@@ramrode5350 please name the library you want. I can give the link to download as zip.

@@ElectroRetro ok I will send you

Baat to sahi hai

For schematic and code:- www.instructables.com/DIY-ESP32-Based-Dual-Phase-Interleaved-MPPT/

​@@ElectroRetrobut the library for Arduino IDE it's Not Working. Because this is not ZIP format Need ur arduino ide in zip format So how do I add these libraries In Arduino IDE ?

@@ramrode5350 place all files in same folder and open it using Arduino ide. After that you can install libraries from Arduino library manager.

Yes