The only video that actually helped thank you very much for your time and knowledge
@trxtech30106 ай бұрын
Glad to hear that it helped!! Thank you for the Posative feedback.
@trxtech3010 Жыл бұрын
just for anybody that wants to know yes I may not instal C Clips how Service Manuals say to, however it doesn't matter because the only reason any service manual tells you this is just for ease of removal of the old C-Clip.
@Moto4Husky2 ай бұрын
That's how I put it in my 88 yz 80 recently and haven't had any issues at all. And that's with a used circlip (new one got launched into oblivion unfortunately).
@leekilgore47116 ай бұрын
Dude thank you. Wholly crap it worked
@trxtech30106 ай бұрын
You're welcome! Goad to hear it helped!
@AronStensaa10 ай бұрын
Don't line the opening of the cir clip with that notch. That's how you remove them if the opening of the cir clip is lined up with that notch, there's nothing to grab onto with your pick to remove it, if you need to 😢
@trxtech301010 ай бұрын
It's only like that for ease if removal... So no it will not mess anything up.
@AronStensaa10 ай бұрын
6 or 12 o'clock is best.
@Airman..10 ай бұрын
Wont work on 2nd clip with short piston pins
@javiertablas-tapia73886 ай бұрын
Great tip worked first try
@johnnyhonda75765 ай бұрын
You need to have the wire in the cutout. Last 1/2” of the circle so you can get a pick in there to remove the clip
@trxtech30105 ай бұрын
I know this...
@pingpong96562 ай бұрын
That is wrong, because now you can't extract it.
@trxtech30102 ай бұрын
I can extract it just fine after that....
@pingpong96562 ай бұрын
I would like to watch that video... LOL
@trentgrace898310 ай бұрын
I was worried I might damage the retaining ring by doing it that way but am very happy and relieved to see it can be done that way this video was exactly what I looked for🫡
@trxtech301010 ай бұрын
Glad to have helped.
@Hijo._2 ай бұрын
…and then “círclip” springs loose; wrist pin walks outward toward cylinder wall, good night, sweet dreams 💤 you growling 318 La Small Block you…
@trxtech30102 ай бұрын
lol what?
@JG-do6eb Жыл бұрын
I always thought opening on clip went on bottom when working on dirt bikes eons ago...
@trxtech3010 Жыл бұрын
installed them in all different directions. I've never had an issue all of these years. Thanks for watching 👍🏻
@JG-do6eb Жыл бұрын
@@trxtech3010 i understand that but still doesn't mean its correct ..I believe i am correct ... you should research and learn more if you are doing things correctly ...it would suck if ypu lost an engine over your ignorance ...good luck
@JG-do6eb Жыл бұрын
@Jason rood opening up or down on the old motorcycles / wiseco pistons ive installed....but could be different on application in others..
@JG-do6eb Жыл бұрын
@Jason rood ok..if that's correct or is that your guess?? Stupid is what stupid does
@trxtech3010 Жыл бұрын
@@JG-do6eb once again, I've been doing this for years absolutely never had an 1 issue...
@napper14964 ай бұрын
Very close to damaging the groove with your screwdriver bud.
@trxtech30104 ай бұрын
LMAO, comments like this or what give me a chuckle as people who have never touched an engine once in their life will sit there and try to tell me what I'm doing wrong and what will happen and so on...