Plasterboard fixings- The good, the bad and the useless!

[@lazerlazer]

From the Eastern Seaboard of the United States. I was almost pulling my hair out with these plastic anchors tonight. Even though it's almost 2:30 in the morning in London It's 9:30 here and I can get my project done now thanks to you. Just a great presentation. Thank you so much.

[@ultimatehandyman]

I'm glad the video helped ;-) Thanks for the comment

[@therealKINDLE]

I am so glad you demo'd the Gripit at the end. Because I have NO room behind the plaster board. So it saved my life.

[@ultimatehandyman]

They are very useful in such situations ;-) Thanks for the comment

[@yayafitini]

THIS IS WHAT I CALL A USEFUL VIDEO

[@ultimatehandyman]

Thanks for the comment ;-)

[@ontourxp]

What would be the best one to hold a 2.6k projector from a plasterboard ceiling?

[@nieeeric]

Absolutely

[@peterbdavies]

I have always struggled with plasterboard walls (rarely with brick walls) and it usually involves a lot of swearing. I have just had to take some shelves down that were sagging and falling off the wall. I got some new shelves repaired the wall and searched the internet and came across this video. I opted for the redi drivers as I can get those at B&Q. Most of the others I can't find there. I have struggled with redi drivers in the past but your tips on screw length etc were a life saver. Apart from one of the eight I had to do, where there seemed to be filler/brick behind the board, everything is now up and secure. Great video!

[@ultimatehandyman]

Thanks for the comment

[@Lando1020]

Great video! It's nice to see the back of the board and observe exactly what is happening when being tightened. Thanks a million!

[@ultimatehandyman]

Thanks for the comment

[@estefilopez292]

2.31mins in and I already know why I've been having so many issues!! Been using the wrong stuff all along! Thanks for sharing and hopefully this new knowledge will help me get over my hate for plasterboard walls!

[@ultimatehandyman]

I'm glad the video helped Thanks for the comment 👍

[@ronjohnson9853]

May I just thank you for the demonstrations. It is amazing to see what happens to the toggles etc on the other side of the wall. Especially as I am about to fix a rotatable television to a breeze block type wall. Thanks again.

[@MohammedAli-1]

Probably the best video on plasterboard fixings available on KZbin. Well done, and thank you.

[@ultimatehandyman]

Wow, thanks!

[@cargorunnerUK]

Great video, so helpful and clear. I had bought the plasplug heavy duty fixings on the advice of the screwfix staff, the fixings that snap and fail every time. I am now going to take them straight back. So glad I found your video before opening the box ! Thanks

[@ultimatehandyman]

You are welcome Thanks for the comment ;-)

[@miophx8283]

Extremely informative video with no wasted time. Probably the best video I've ever seen on KZbin with regard to quality information and efficiency of time!

[@ultimatehandyman]

Thanks for the comment 👍

[@fz7n71]

Perfectly explained and right up to date. So glad I watched this before rushing into the job.

[@ultimatehandyman]

I'm glad the video helps Thanks for the comment ;-)

[@roybatty4687]

Up to date 5 years ago.

[@PJBonoVox]

@@roybatty4687 No shit, Sherlock.

[@ontourxp]

@@ultimatehandyman hi what is the best and strongest to be able hold a projector from a ceiling?

[@megapangolin1093]

Briliant video, very clear, straightforward with honest comments about performance, pros and cons. Just what people need. Thank you.

[@leoreggaebwoy]

Mate, brilliant video. The crap fixings should be banned and taken off the market as they are a waste of time and knackers you up! So frustrating. Keep uploading these vids believe me they are very much appreciated👍

[@ultimatehandyman]

Thanks, I'll be making more videos when I get chance ;-) Thanks for the comment

[@sylviavillalobos8574]

Amazon video. Thanks

[@glencooper43]

Yeah, you're right. Talk about plastic waste, look at all that crap. The nylon worm screws are worse than useless. The metal ones are the only ones worth buying

[@theblytonian3906]

One of the most useful tutorials on the subject on You Tube. To the point, practical. Thank you.

[@ultimatehandyman]

Thanks for the comment ;-)

[@YehoodToob]

Invaluable information, saved me a lot of guesswork and money! Thank you

[@ultimatehandyman]

You are welcome.Thanks for the comment ;-)

[@thomaskalinoski6121]

Great video! Learned a lot in short time!

[@17zubs]

Great video, what would you recommend to hang a standard size clock?

[@ultimatehandyman]

Thanks, I'd just use one of the worm type screws as they are readily available and inexpensive. Sorry for the late reply, I have just seen your comment!

[@Muckhauler]

Took me years of pain and distress to learn what you have shown in 10mins my friend! Well done - great informative video for avoiding plasterboard disasters and wasting money! Can highly recommend the last item (the red plastic circular discs) just fitted out a load of kitchen wall cupboards using them. Manufacturer boasts a hanging weight of the red ones to 75kg! (Other weights/sizes/colour codes available too). Big tip with them is not to be frightened of tightening the screw right up to ensure a nice secure fitting. Top video👍

[@ultimatehandyman]

Thanks for the comment ;-)

[@JayKay-ht8rg]

Perfect! Just what I was looking for. Need to fix a Wall Heater to a Plasterboard Wall. Think I’ll go with the SnapToggle fixing. It seems the most heavy duty one. Thanks for Posting this. Extremely helpful to me!

[@umartdagnir]

Thanks a lot for this video! I just moved into a flat with plasterboard inner walls, had no experience with them before. You saved me from buying useless cheap stuff and wasting my time.

[@ultimatehandyman]

You are welcome Thanks for the comment 👍

[@jaakkooksa5374]

When using those conical aluminum anchors, it helps if you turn the screw in and out a couple of times when the anchor is still undetached. That way you can avoid using excessive force which will break the plaster board.

[@crackspider101]

Brillaint video. As a new build owner where ALL the walls are plasterboard, this is brilliant

[@ultimatehandyman]

I’m glad you found the video useful Thanks for the comment 👍

[@koffibanan3099]

Great overview, thanks a lot! Now I actually want to hang my whole wall full of junk, just for the sake of hanging things :)

[@ultimatehandyman]

+Koffi Banan Ha Ha, Thanks for the comment ;-)

[@carlosbolanos1070]

This really made me laugth, people now thinks I'm crazy.

[@mj234eva]

Lol, same!

[@Healthhazard43]

Did not even know that snap toggles even existed as not stocked at my local hardware shop. Thanks for a great video (even though it took youtube seven years to suggest it!!!) They look perfect for my next project.

[@ultimatehandyman]

They are brilliant and my number one choice of fixing to plasterboard 👍

[@neildmoss]

+Ultimate Handyman I found the secret of the blue heavy duty PlasPlugs is to use the screw with the smooth neck, but shorter than you ones you tried in the video. The screw should only be as long as the actual length of the plug. The screw bites into the tapped end of the plug when the neck reaches the collar of the plug. The screw then rotates freely in the collar, but the tapped part of the plug is drawn to the wall, expanding the wings against the wall. In your demo, the tapped part of the plug is being driven away from the wall by the pressure of the tapped part of the screw still being driven through the collar. (ps very grateful for your channel... I've refitted three rooms with the lessons learned.)

[@ultimatehandyman]

If the screw is so critical to these fixings working you would expect the manufacturers to supply screws with the product. Thanks for the comment ;-)

[@neildmoss]

Agree - either supply the screws or state what works in the instructions! That said, I may just have got lucky. Does it work for you?

[@ultimatehandyman]

I don't use these anymore and can't remember where I put them, I just made sure they were not with my other plasterboard fixings! Thanks for the comments

[@grizzlygrizzle]

I have found that using a thinner screw helps. Many of the manufacturers specify screws that either break the anchor, or else spin the anchor in the hole in the plasterboard.

[@coolspot18]

The PlasPlugs I bought in Canada work really well - never had a problem with them breaking. I wonder if the ones you got were defective or the screw size wrong? The ones at HomeDepot in Canada include screws, but they're just regular wood screws.

[@happytimes4421]

What an excellent video. Loved the fact you showed behind the plaster board to see how each fixing worked. Now to go buy the ones I need for my shelves.

[@ultimatehandyman]

I'm glad the video helped Thanks for the comment 👍

[@Xenochrist95]

Whenever i knock a hole in the wall too big for an anchor I fill it with epoxy putty and when it dries it holds screws pretty well.

[@ultimatehandyman]

Thanks for the comment

[@3milesong]

Very informative. Thanks for posting.Notes to self; Favorite items:3:24 - Worm Screw Anchor 6:14 - Snap Toggle Anchor8:19 - Spring Toggle Anchor9:00 - Grip-it Anchor

[@ultimatehandyman]

Thanks for the comment 👍

[@jimsear]

Excellent tutorial!

[@ultimatehandyman]

+Jim Sear Thanks Jim ;-)

[@perpetualjon]

By far, the best demonstration of drywall fasteners I've ever seen!

[@ultimatehandyman]

Thanks for the comment ;-)

[@l3ertuz362]

now I understand what's going on the dark side

[@ultimatehandyman]

+l3ertuz Thanks for the comment ;-)

[@ThatFreelance]

Lol

[@gto1066]

Thanks bud. I'm not too good at DIY but you've just made me feel a little more confident with your clear and informative videos.

[@ultimatehandyman]

Glad I could help 👍

[@intotheblue50]

When you use Ready Driver Zinc Worm Screws as you name them, coat them in PVA glue as they go in and they will set solid and consequently be a much stronger fixture. PVA will bond porous to non-porous materials in this way.

[@ultimatehandyman]

Thanks Phil, I don't use them much to be honest but I'll try that next time.

[@159church]

Also why not use drill instead of screw driver it’s quicker and you can set the correct torque needed

[@congaa]

Given the flat tip of these zinc worm screws, it makes sense to start off by tapping them in to position with a hammer, up to the thread. Then use a screw driver with some pressure. This will ensure greater accuracy of the fitting location.

[@stratops]

Well done...also quite comprehensive in a short presentation. Nice to see what's happening inside the wall. Thanks!

[@ultimatehandyman]

You are welcome Thanks for the comment 👍

[@ultimatehandyman]

@harry lewis If it's a hollow plasterboard wall I would use snap toggles or the blue Grip it fixings. If the wall is plasterboard with a solid wall behind I would use Rigifix fixings. kzbin.info/www/bejne/rpK8l6ZpoddkoKs

[@markusfinski3715]

+Ultimate Handyman wow am a plasterer and I didnt know the "Grip It" fixing existed lol... I have plasterboard with solid wall behind it, and in between them I have pipes. So I think Grip It would be my only choice seeing I can only go deep as the plaster board (I have a gap of few mm between hard-wall/pipes and plasterboard). Thanks for this awesome video m8

[@ultimatehandyman]

+MarkUs FinSki You are welcome Thanks for the comment ;-)

[@jackjill3205]

+Ultimate Handyman snap toggle or grip it what would you say is better best for using generally and using to hang kitchen cabinets and tv brackets

[@ultimatehandyman]

After testing many plasterboard fixings I'd go for spring toggles in most applications as they are inexpensive and can hold more weight than some of the other fixings- kzbin.info/www/bejne/e3Snqqacg82rlac Thanks for the comment ;-)

[@BrianBell4073]

+Jack Jill....It would be normal to install what we call 'grounds' in kitchens with plasterboard walls. Like noggins, but the grounds are lined up just below the height of the top of the cabinet. Basically horizontal pieces of timber attached to the stud work for the specific purpose of hanging wall cabinets. If you must go for a plasterboard fixing then keep all your plates in the base units ;-)

[@ianian8022]

For any Americans who may be watching this (and to annoy my fellow countrymen as well) the man in the video is talking funny because he is from the North of England. He does however, know his fixings and though you may think he is demonstrating the bleeding obvious it is comforting to know that your workmate who seems able to use the blue fixings that you keep snapping is either uniquely capable, very lucky or is going to get a phonecall from the boss next week to say the speaker, projector, interactive whiteboard, whatever, he fitted at that last job has just come off the wall and narrowly missed a school kid etc. etc.

[@nicolek4076]

I'd say, more specifically, that he comes from the North-West of England: Lancashire or Manchester. Doesn't sound like any sort of Yorkshire to me.

[@ultimatehandyman]

That's correct. Darwen, Lancashire ;-)

[@caskwith]

Very nice round up there. Great to see the fail points on camera, those plasplugs were utter crap! Never used the snap toggles myself but they look very good, used most of the others in some form and for my money it's very hard to beat umbrella fixings, strong, permanent, easy to fit (I don't have a tool) and cheap as well. What is the load rating difference like between the snap toggles and the umbrella fixings? Are snap toggles a bit more heavy duty?

[@ultimatehandyman]

+caskwith Thanks, I'm going to do a video soon seeing what weights some of these fixings can hold in plasterboard. I think the snap toggles are more heavy duty than the spring toggles, but have not tested them to be 100% certain yet. Thanks for the comment

[@sharonlee4773]

Thank you so much for your clear,straight forward advice! So many on youtube just love listening to their own voice and waffle on forever.Great video,most helpful.

[@ultimatehandyman]

Glad it was helpful! Thanks for the comment 👍

[@nsleavitt1]

Would someone please buy this man a cordless screwdriver.

[@Toontex]

It is advised to use hand driven screwdrivers with all these fixings when used on plasterboard

[@markslade9722]

Very informative video showing lots of different types of dry wall fixings, and seeing how they work or don't work in some cases from behind the plasterboard, that we would never get to see ourselves while using in a real life scenario👍

[@ultimatehandyman]

Thanks Mark 👍

[@seabcarolan]

Very useful video. I appreciate that you referenced both Metric and SAE sizes. There are two kinds of countries in the world, those that use the Metric System and those that send men to the moon. Just kidding, great work my friend.

[@ultimatehandyman]

Thanks for the comment ;-)

[@ianowen9717]

Once again a useful video. Those reading these comments might want to consider using 'Bullfix' fixings, which are similar to the 'GripIt' but have wider plastic wings on the inner wall side. I have just used four of them to hang a 43" QLED TV on a stud partition wall and it's rock solid, much to my amazement. The pack I purchased had 10 fixings, corresponding screws and the necessary 20mm drill bit, all for around £10, so enough left over to hang another TV.

[@ultimatehandyman]

I recently tested the Bullfix extra, although the video has not been made public yet- kzbin.info/www/bejne/nma4onyirJtkjNk

[@elliottlandon8420]

amazing video thank you really helped me decide how to hang my tele off plasterboard much appreciated

[@themanwithinflatableknees8770]

To mirror everyone else, what an excellent video. Very well explained without the crap so many use.

[@ultimatehandyman]

Glad you liked it! Thanks for the comment 👍

[@flipmode00]

2019 and I like this video

[@ultimatehandyman]

Thanks for the comment

[@ThorntonValiant]

Great video. Really helpful. I actually watched this after buying some heavy duty Plasplugs. I used them to put up some shelves for light use. I actually found them to be really good. Did the job well. The shelves are only to hold DVDs but really secure.

[@ultimatehandyman]

Thanks, Alan. I did not have much success with some of the Plasplugs fixings. Thanks for the comment

[@1971dave]

what I do is drill through the wall in to next room and put a steel plate .on the wall. 6 inch square and 1 inch thick. 10 mm bar and bolt it down..and that is hang anything on it

[@racketman2u]

Specs sound reasonable, but to avoid undesirable shear loading, i would actually recommend drilling across that room and into the far wall.

[@johnmccallum8512]

This is quite common if you were to look up at some of the older buildings you will see a cast iron plate with a nut in the centre. Saves rebuilding the wall for some time.

[@Bazlightyear007]

proper hardcore. question is: is it bulletproof though? :)

[@andybell9245]

Good neighbour

[@InCountry6970]

Dave Jenkins, you crack me up. Very funny !!!

[@adammorrow651]

I hate the spring toggles, they don't work in modern homes with insulation in the walls, they just get caught up in the insulation and don't work for me.

[@ultimatehandyman]

Surprisingly they are one of the strongest fixings available! Thanks for the comment

[@adammorrow651]

They are only rated at around 10kg and I have found many others that are rated at 15kg and heaps easier to install. The tabs don't seem to spring out when there is any insulation in the walls.

[@ultimatehandyman]

I tested some out in this video and they were the best performing plasterboard fixing- kzbin.info/www/bejne/e3Snqqacg82rlac Perhaps you could try moving some of the insulation away from the hole?

[@ccmogs5757]

Try Fischer 6mm plasterboard plugs for light-med. duty :]

[@airzone2332]

They are the only ones I use. Find they are the strongest.

[@BigStew007]

Very good demonstration of the myriad of plaster board fixings available. Personally I've never found one that "suits all".

[@ultimatehandyman]

Thanks for the comment 👍

[@stokiechris462]

you dont need a setting tool pal

[@ultimatehandyman]

Yes, I know but some people have had issues with them not biting and spinning in the plasterboard ;-) Thanks for the comment

[@jasonmcnamara2079]

its the best way for the best possible result

[@hiltos]

Huh didn't even know that there was a setting tool. I just tap it with a hammer and screw it in so it mushrooms.

[@djsgrant]

Great video. People who have given this the thumbs down are morons.

[@johnbarnes4420]

Far easier with a tool

[@toysintheattic2664]

You just made the very daunting prospect of hanging my tv in my new home a lot easier. Thank you

[@ultimatehandyman]

+John Davies You are welcome. Thanks for the comment

[@dan55yeah]

He lost my respect when he started using a masonry drill on plasterboard...

[@ultimatehandyman]

What would you use on plasterboard?

[@felinthorn4977]

Here in the USA the home of wallboard.... Being a soft material you will find a wood drill bit does a much better job! If the item to be hung is less than 10lbs/4.5 kilos a nail driven down at a 45degree angle into the wallboard is more than adequate. And no we do not skim coat wallboard with plaster! Just tape & mud the joints, mud the screw holes, light sand to smooth and either texture, prime and paint or just prime and paint. Why pay hundreds extra in material & labor when you could never tell the difference. Other than our way won’t crack!

[@zacharythebeau163]

@@felinthorn4977 I disagree here in the USA we call it sheetrock or drywall. PS there are areas of that USA that call it plasterboard and the "mud" is a skim coat. Here in the area of the USA were I live it's call joint compound.

[@kevindesilva1311]

@@felinthorn4977 Sorry but plasterboard was invented in the UK and we have been using it longest . We either mesh tape every joint and then skim it with plaster or paper tape the joints and sand . I have been putting it up for over 45 years and skimming definatly produces a superior job . Which is far less prone to knock damage . I find that a masonary drill in a drill not in hammer mode produces the best hole for fixings

[@sneakydoyle]

Why would you use a wood bit. HSS bit with no hammer action, sorted.

[@as680783]

Exactly the video I was looking for. I need to hang a heavy-bag (punch-bag) weighing about 40kg to my plasterboard main wall, which doesn't appear to be dot-and-dab. The 10mm/7cm wall plugs that come with the wall stand don't look sturdy enough for the job. Looks like I'm going to need the Grip-It fixings for a proper job. Many thanks for the tips and interesting plus informative to see the actual mechanics of how these things work on the 'other side' of the wall. Superb stuff!

[@KarrsmyBoa]

Great video we've just bought some cupboards from ikea and I only said to my partner last night that I didn't know what type of fixing to use and then this video pops up for recommended viewing 👍👍👍

[@ultimatehandyman]

I'm glad the video helped ;-) Thanks for the comment

[@glendaboard1927]

Matthew Pearsall

[@AdyB2008]

Brilliant as ever! Pretty sure you're now my No1 KZbin DIY goto guy! Cheers!

[@ultimatehandyman]

Wow, thanks!

[@davidrowe8747]

Great video, just what I needed. Fitting an Ikea Tretur roller blind upwards into the top of a window cavity/window bay. It was straightforward in the toilet - plasterboard over a lintel, so I used gradually increasing drill bits, and masonry bit for the last 0.5cm or so. Then used ordinary wall plugs, which have given a firm attachment. However, the apparently similar situation in the bathroom is not the same at all. Drilling into the plasterboard, there was very quickly no resistance. Poking a bradawl into the drill hole, it's clear that there is a cavity on the other side of the plasterboard. As the roller blind involves pulling downwards, it needs to be a secure attachment - I think the snap toggle is probably best (because the holes in the bracket are quite small, and fairly closer together, so the other options would involve drilling wider holes, close together - could cause the plasterboard to fail completely).

[@davidrowe8747]

Just finished - a 4-hour job including a trip to Screwfix! It was a bit fiddly because .... well, Ikea. I've now screwed into stone lintel a few times and think it would be a good video for you to do. ;-) (I've never come across the situation above before. It was a bit of a bugger, because (a) I didn't know if there was enough space for the toggle to spring open before it hit the lintel, and (b) if the screw didn't go straight, it wouldn't go into the gap I had drilled in the lintel to allow me to screw it fully in. I think one of the 6 screws actually did hit the lintel, and I ended up having to leave about 2mm of it sticking out, but thankfully it didn't impede the roller blind clipping into the bracket. Phew! I always have a nervous moment doing even basic DIY, when I have made a dickens of a mess and think, "If this doesn't work, I have 6 lovely big holes in my newly-painted plasterboard"!

[@juliaschwartz8568]

Oh my god i was screwing something into a wall when this video auto played. the beginning made me think i hit a pipe and i panicked. seems like everyone else loves your videos 👍

[@ultimatehandyman]

Thanks for the comment 👍

[@rbishop4495]

Excellent video and to the point narration. Extremely useful for the DIY divas amongst us.

[@ultimatehandyman]

I'm glad the video helped Thanks for the comment 👍

[@BrijeshYadav-vl7bj]

This is a cool video which makes you understand various options for drywall fixing for various situations. Thanks for detailed explanation. Liked your accent and the way you speak. Cheers.

[@ultimatehandyman]

I'm glad you found the video useful ;-) Thanks for the comment

[@GreenGaslight]

Fantastic video. the most definitive video I have seen on plasterboard fixings by far and the rear view was very interesting. I keep a box of those plasterboard plugs (grey) on the van. good to see that they are actually as good as useless for the applications I would use them. I didn't get the point of those large ones at the end, they don't look as strong as either the snap toggles or spring toggles but you have to make a massive hole. Spring toggles are my go too when I need a good fixing. Snap toggles look good but are not cheap!

[@ultimatehandyman]

+EssexSpark Thanks ;-)The snap toggles are my favourite, they are far superior to other plasterboard fixings.Thanks for the comment

[@merlin5476]

Excellent info. I've just done some tests at home with 2 layers of 12.5mm plasterboard. Yesterday i fitted 6 ceiling lights for a customer, each light was around 5kilos, so i used 3 of them metal screw types per light, but you reall MUST ream them out 1st , hold em with pliers & put the screw in a couple of times. My test at home involved me using 2 ( screwed into double thickness 12.5mm board) i could pull nearly 50kilos before they popped out. Ive seen quite a few videos of tradesmen just using an impact wrench to screw in the metal ones which in my opinion will normally spin the " metal fixing" and your then left with a large hole.

[@ultimatehandyman]

👍

[@AndyDaviesByTheSea]

Hi thanks for the review I was just about to order a bunch of Plasplug heavy duty plasterboard fixings from Screwfix, glad I didn't bother.As a young electrician I used to use the metal hollow wall anchors about 40years ago, they used to come with a small pressed steel spanner that had a hole/slot to let it slide under the head of the bolt and it had two ears pressed down that projected into the wall anchor, this stopped the anchor from turning, they were great and you didn't need to buy a fancy setting tool.Good review well done.Kind Regards . . . Andy

[@ultimatehandyman]

Thanks for the comment, Andy 👍

[@davebrown9496]

Thanks for that, excellent video without loads of waffle! You have an impressive range of gloves!

[@ultimatehandyman]

People were always asking me why I wore gloves, so for a laugh I worse several different pairs during a video that I made (it must be this one). Not many people picked up on that fact 😂 Thanks for the comment 👍

[@21TGH]

Brilliant, i've tried many different plugs in the past and many have failed, like you've shown here, I thought it was just my curse. Looks like I need to try the Grip-it fixings to hang the TV on the wall.

[@ultimatehandyman]

The Grip-It fixings work well. Thanks for the comment ;-)

[@Jjustbyherbal]

I've been struggled to mount my TV on a drywall since the kit that comes with the mount only includes parts for concrete wall/wall stud. Your video is so helpful! I am gonna go with the snap toggle.

[@ultimatehandyman]

I'm glad the video helped Thanks for the comment 👍

[@reddevil9554]

Very informative. I've been using the metal collapsible ones for years and didn't even know about that tool - will have to get one. I just used my sense of resistance to tell if they were collapsing nice and neatly.

[@ultimatehandyman]

👍

[@Fruit_-iv6if]

Very informative video. Good too actually see what goes happens on the other side of plasterboard. I am going too hang a 65 inch tv and have been looking around for the best fixtures too use. You have really helped me solve the problem.thanks .

[@ultimatehandyman]

This is worth a watch- kzbin.info/www/bejne/nZ3dqIxta7Rjmpo Thanks for the comment 👍

[@Fruit_-iv6if]

@@ultimatehandyman cheers watched it. Just curious what your views are on the geefix fittings for plasterboard. They look good since the mass spread out behind wall should disperse the weight better. What ya think.

[@ultimatehandyman]

They are okay, but spring toggles and snap-toggles held more weight in my test- kzbin.info/www/bejne/e3Snqqacg82rlac

[@Fruit_-iv6if]

@@ultimatehandyman perfect just the video I was looking for. I'm looking up as much info as I can. Don't want my new TV crashing down lol

[@EGE3101]

Very good. Systematic and adequate demonstration of the options. Thanks!

[@ultimatehandyman]

Glad it was helpful! Thanks for the comment 👍

[@RohanBarnard]

First time having to fix something to plasterboard. This was invaluable, thanks!

[@ultimatehandyman]

I'm glad the video helped Thanks for the comment 👍

[@n00bma5ter69]

Wall Anchors are 🔥. Couple of squeezes from the "tool" and they are firmly locked in. I've hung heavy mirrors and paintings with them and no issues

[@ultimatehandyman]

👍

[@FaithfulandTrue777]

Thank you for this, such a help when you have to be mum and dad! God bless you.

[@ultimatehandyman]

You are so welcome! Thanks for the comment

[@vicster9401]

This is an excellent video and a great demo of the various fixings available - good job ! - Thanks

[@ultimatehandyman]

Glad it was helpful! Thanks for the comment 👍

[@dynamitebucket]

Great video - gives us such a great understanding of how each fixing works, both on the visible and non-visible side. Very nicely done!

[@ultimatehandyman]

Thanks for the comment ;-)

[@adnanalshboulvarieties]

Amazing Hanged a big tv on a concrete wall and needed to hang another on a plaster board , but stopped not knowing how to go about it with the risk could result from that , but know I feel confident for the job Thanks a million

[@ultimatehandyman]

I'm glad the video helped Thanks for the comment 👍

[@Wolverine6617]

Hey there Ultimate Handyman. Thanks for the video. A lot of these I had seen but some are new to me. Very interesting as I do a bit of fixing into walls and now after watching your "road test" I am going to try some of these others. The ready driver in Australia is called a wallmate, same thing and yes it comes in aluminium and nylon. Cheers.

[@ultimatehandyman]

Thanks for the comment

[@ameen0digi]

From 3 years until now still very informative thanks mate

[@ultimatehandyman]

I'm glad you found the video useful Thanks for the comment 👍

[@laughingspirit]

Brilliant video. Thanks! I am doing a number of projects that require drilling into plasterboard instead of hitting a stud and was not sure how all the wall anchors differed in effectiveness. This video was very helpful!

[@ultimatehandyman]

I'm glad the video helped. Thanks for the comment

[@paintbox48]

Brilliant - informative and comprehensive, without any waffle.

[@ultimatehandyman]

Thanks for the comment 👍

[@Chewy7575]

That was excellent, thank you. I knew how they worked but seeing it from the rear of the plasterboard was great. I've a TV to put on a cavity wall with no studs near it, so was thinking about using Gripits. Definitely will be now. Thanks again.

[@ultimatehandyman]

I'm glad the video helped ;-) Thanks for the comment

[@Chewy7575]

@@ultimatehandyman I ended up using Fischer Duotec fixings. There was a section of chipboard behind the plasterboard which made it too thick for the Gripits. I found the Duotec to be excellent though.

[@DoubleOProductions]

Plastic snap toggle or spring toggle all the way...no question! They've never let me down!

[@ultimatehandyman]

Thanks for the comment 👍

[@DuFaou0]

Very handy video, Thank you. I used the plasterboard fitting which you used without the setting tool and it worked fine with an impact gun.

[@ultimatehandyman]

You are welcome Thanks for the comment

[@jeanknowles680]

I thought this video was very well made, clear, easy to understand and a great help. well done and thank you.

[@ultimatehandyman]

You are welcome Jean, Thanks for the comment.

[@yasmahmood6545]

I'm new in the game, I've seen people use the hollow wall anchor, but not like you've done. All they do is hammer it in, and put in a screw, they do not pull the screw out for the back to get a grip cheers dude.

[@ultimatehandyman]

Thanks for the comment

[@mohammadtahir8785]

This is the most comprehensive video I have ever seen on fixings, thank you. Subscribed!

[@ultimatehandyman]

You are welcome Thanks for the comment

[@nisbend]

Very useful, and always good to hear the sound of the tools and the narrator rather than generic wallpaper muzak

[@ultimatehandyman]

I’m glad you found the video useful Thanks for the comment 👍

[@milesfb]

Useful video. It definitely appears thatnthe snap toggle is the best good all rounder to take heavy loads such as a tv and its bracket.

[@ultimatehandyman]

The spring toggles performed better, when I tested them out- kzbin.info/www/bejne/e3Snqqacg82rlac Thanks for the comment

[@MadMonique]

Excellent. I love being able to see the "inside" parts. Thank you!

[@ultimatehandyman]

You are welcome Thanks for the comment

[@DawgNo1]

Thanks for the vid, I haven't tried the snap off fixings so will look out for those, I have 2 plasterboard fixings on my van, the worms and Gripit, its a shame Gripit are going down the pan so I was looking for a replacement, there claim of 113Kg is amazing, ive never hung anything that heavy but I have used them for very large tv's when there has been no stud. Just to add, I've used thousands of those metal worm screws and never ever had a problem with the supplied screws, yes they bottom out but they have never damaged the wall when tightened up, there's an exit hole at the bottom so I figured that's exactly how they intended them to be used.

[@ultimatehandyman]

The snap toggles are superb and are my favorite plasterboard fixing, they now sell them in Screwfix under the Timco brand - fave.co/31B0MsC This video shows how much weight certain fixings can hold before the plasterboard fails- kzbin.info/www/bejne/e3Snqqacg82rlac I've not used the metal worm screws for years, but the ones I used did not have an exit hole for the screw. Thanks for the comment 👍

[@mikewellwood1412]

@@ultimatehandyman Thanks for confirming that the Timco ones are in fact snap toggles (as that's not what Screwfix seem to call them). Anyway, just bought some as they certainly looked like snap toggles. The only slightly scary thing is the relatively large hole that you have to drill.

[@wickedleeloopy2115]

never had luck with nylon plugs. Im sticking to the reaady driver/ wallmates .works every time for most aplications including hanging paintings & fixing thermostats for heaters.👍 good video as most people have no idea how these things work

[@ultimatehandyman]

Thanks for the comment Lee ;-)

[@danicquinn]

Your videos are SO HELPFUL! Thank you. I have just moved to my first home and this has really helped with navigating new projects.

[@ultimatehandyman]

I’m glad the video helped Thanks for the comment 👍

[@DINESHCO]

Very Clear and nice. Please add a video with best Rawl plugs for common jobs (e.g Ikea book case to wall fix, Mirrors etc)

[@ultimatehandyman]

They are all pretty much the same, regardless of the make. This might help - kzbin.info/www/bejne/jGXah6yvm8eKpck&t Thanks for the comment 👍

[@innocentoctave]

Excellent overview: well done. I've seen similar remarks about the Plasplugs heavy duty plasterboard hollow wall anchors elsewhere, though some people use them without problems. The manufacturer does supply screws with some packs: they appear to be simple number 8s, so this isn't a problem with using the wrong screw.

[@ultimatehandyman]

Thanks for the comment

[@alanbox6169]

Brilliant Video and explained EXACTLY which ONE of the FIXINGS that I had available were the correct ones for the Load in Question as I used some Nylon One's originally that were OK on some of the WALLS but started to give way ONCE a LOADING was added and so I replaced with the SPRING TOGGLE and this has WORKED VERY EFFECTIVELY! The whole of My House is PLASTER BOARDED over STONE WALLS and so it is great to know the DIFFERENT VARIETIES to be USED for different SUBJECTS! I think that the ONE that I take out of the VIDEO as being the BEST is the SNAP TOGGLE which appear to be the Most Expensive as well but if you are looking at HEAVYISH LOADS then I think that fits the Bill EVERY TIME! alan box

[@ultimatehandyman]

Thanks for the comment ;-)

[@sergeydukman5832]

To me the hollow wall anchors are by far the best fixing available for plasterboard walls.

[@ultimatehandyman]

I tested them out here, along with other types- kzbin.info/www/bejne/e3Snqqacg82rlac

[@tim_tim_tim]

Fantastic video - really wish I'd watched this a few days ago before attempting to hang some curtains with plasplugs - at least I now know that they are garbage and to not take it personally :)

[@ultimatehandyman]

Glad it was helpful! Thanks for the comment 👍

[@jasminderventa]

Great video! Thank you man, you saved me trouble, these Snaptoggles are amazing for plasterboard.

[@ultimatehandyman]

Glad I could help 👍

[@TheNailSpecialist]

Very good video and great to see the difference versions some I’ve never seen before

[@ultimatehandyman]

Thanks 👍

[@briansansone]

I tried them about 10 times too. You have to use the perfect diameter screw, fine thread, and be really nice to it. They look useful. I have never got them to work well. The nylon "ready drive", as the author calls them, splitting type work extremely well. They split open when you drive a screw through it. No worries about bottoming out. They claim 75 pounds. probably 75 straight shear. Brian-Custom Window Treatment business

[@ultimatehandyman]

Thanks for the comment 👍

[@r12daf]

What a great video. Im going to be hanging my TV to a cavity wall soon and was doing some research on the best fixings for the TV bracket. I do often use M4 38mm heavy duty plasterboard anchors but as its a heavy tv i need something more sturdy. I think ill be looking into the grip it fixing. Great Video. Thanks

[@ultimatehandyman]

+Daniel Ford You are welcome.Thanks for the comment ;-)