Polaris Trailblazer 250 pre-mix conversion

My affiliate links
I listen to audiobooks all day while working. This link is a free 30 day trial to Audible.
amzn.to/41hP0ln
The ear buds I use
amzn.to/3KSSlBL
Link to the 3/8 impact I use
amzn.to/3Ii99An
Link to the 1/2 impact I use
amzn.to/3Jg3Q58
Link to the cordless ratchet I use
amzn.to/3Ii99An
Allen sockets I use
amzn.to/3lqHDYu
Link to the best carburetor jet reamer set on the market
amzn.to/3mpFmgO
Our own "Make Carburetors Great Again" T Shirts!
my-store-10172...

[@allischalmerswd]

So why not just leave the oil pump in place and just disconnect the cable?

[@JS-ov5vd]

When I look up oil block off kit for trailblazer 250 nothing comes up is there may be a part number you have that I can look it up?

[@Donblgoodrimes]

Watched your vid you did a year ago on oil mix pump on cycle engine. Replacing with a block plate. Isn't the throttle attached to that pump. If so, where do you attach it after pump is removed. I don't have it out yet but looks like it's on the oil mix pump. Can you advise me.

[@donwalters8877]

All you have to do is disconnect the inlet line and run pre mix????

[@kraftcraft2934]

That's what I did undid the cable 🚡

[@mr.uhleven]

you didn’t have to use the block off kit correct ? another question.. will my trailblazer be okay if i just do premix and leave the pump on the bike ?

[@AnthonyMartinez-bj7xi]

Yes i run it whir the pump still on it

[@rivit7615]

I would think that you'll need to plug the oil supply line going into thepump. Otherwise it will allow some extra airinto the carb through the pump inlet. Lean means heat and eventually extreme wear or seizure. ​@mr.uhleven

[@rivit7615]

I read that the oil lubricates the pump so it's likely to eventually lock without it. Imrunning premix with pump in also. Hmmm​@@AnthonyMartinez-bj7xi

[@AnthonyMartinez-bj7xi]

@@rivit7615 yea i have it covered

[@gabrielalvarez9570]

Cool so there's no need to pull the gear from inside that crankcase that drives the pump?

[@hillsidepowersportrepair8863]

Depends on the application, but usually no

[@gabrielalvarez9570]

I saw some videos where they did but personally i don't see the need to, it would just be free spinning in there 🤷🏾‍♂️ Thank You! 🙏

[@robertharrington3691]

Do you have a link to the kit you used in this video? Thanks

[@hillsidepowersportrepair8863]

www.ebay.com/itm/252977786537?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=ZsCtC8T2Rv2&sssrc=2349624&ssuid=AkYs3VdFQMy&var=&widget_ver=artemis&media=COPY

[@shawncordeiroTerraceBC]

why not let oil tank run low and dont touch a thing start pre mixing ?

[@hillsidepowersportrepair8863]

The 2 stroke oil lubricates that little pump. It had been known to lock up without oil

[@RobertSwem-g4y]

Will that same play work for a trall boss 250

[@RobertSwem-g4y]

Plate

[@hillsidepowersportrepair8863]

I believe so

[@steelcold3912]

Do you have a link for the cast jet cleaning tools? Thanks for the video.

[@hillsidepowersportrepair8863]

amzn.to/3PGVXJC Have fun!