Pontiac Grand Am/ Olds Alero 3.4 liter powersteering pump replacement

[@alexgordon9998]

Man that was the most detailed video yet on KZbin for power steering pump replacment for the 3100-3400 gm engine. Thanks man for the tutorial

[@injunjoe5]

This is a great video. I used it on a 2000 Alero. I could not find a new or used p/s pump with EVO sensor. I bought a pump for $40 and rebuilt it with my reservoir and clips and sensor connected to the with high pressure inlet hole. I did not know but it does spin off the old pump. You need to take the sensor off first with a C pliers and snap ring pliers and after, put it in a large vice to hold and loosen the high pressure hose inlet. Change all the O rings in the new pump then put it all back together. This would be a good video to make. Many people ask about this procedure on the internet. Pulling and putting on the pulley is easy with the borrowed rental tools. Blow out your lines! There is a tremendous amount of sludge in them and it is not hard to do but very messy. Take precautions and don't lose the nipple which is in the low pressure inlet hose or on the reservoir nipple. Thanks for the help!

[@exxtraamusic4151]

Even today your video is helping people thank you

[@JoeTheAutoGuy]

Thanks for watching !!! Glad I could help

[@johnnydegeorge2132]

Joe.... Dude...... I set the quality to HD1080 and BOOOOM..... I was standing right over the top of the engine. :) Thanks for the extra high res. :)

[@grahamrees87]

i feel so stupid now. i couldnt find any bolts holding the pump on but now i know where they are. this video helped alot

[@JoeTheAutoGuy]

Graham Rees thats why i make the vids , glad i could help

[@thorthunder3227]

Thanks, i forgot how to put my pump back on been off for 6 years. Got it all rebuilt now after running a hundred miles to find my bolts and put them in the right spots.

[@sjagain]

Excellent video. I watched because I needed to replace my camshaft position sensor which as you know is under the PS pump...What a crappy place to put it!

[@JoeTheAutoGuy]

thanks i actually am working on a video just for that on this engine !!!! thanks for watching

[@dakotawilliams329]

woulda been nice if you would have included the sizes of the bolts. Thanks for the overview of the process.

[@JoeTheAutoGuy]

good note , some years changed sizes so hard to always have that information handy but il make more of a effort in my how to vids

[@actingbearded573]

Great video, if never done anything like this before but with your video I changed my pump with no problem at all.

[@JoeTheAutoGuy]

glad i could help you out . thanks for watching

[@topherd1011]

I did this about 3 years ago and it's starting to leak and whine again so it's time.. Just brushing up; thanks man.

[@DoctorCreepy13]

Exactly what I needed! Your video is still helping people. Thank you!!

[@JoeTheAutoGuy]

thanks for watching !!!!

[@travboat]

The ratchet strap on the tensioner pulley is such a brilliant idea. I bought a tool with a square peg a while back, but it does not have enough travel to release the tension.

[@JoeTheAutoGuy]

+Trav Hall that was my thoughts exactly

[@johncoleman201344]

you are the best you are straight to the point on getting it done an this this same motor i have im glade i found you now i know how to fix my own car thanks bro

[@JoeTheAutoGuy]

thanks for watching

[@rod65man65]

Best vid on the subject matter at hands , thanks alot.

[@digitalcynicism]

Great video thanks for this. i am helping my dad replace his PS pump right now and the only thing i am wondering is how do you get the Pulley Wheel back on the pump??

[@walterward7922]

Thanks for Showing everything from start to finish that was very helpful very informative video and a success on my own vehicle

[@rickytimms446]

Thanks a million. Really appericate the time and effort in your videos. Very imformitave and well put together !!! They're life savers for us do it yourself guys...Thanks again !!!

[@JoeTheAutoGuy]

+Ricky Timms thanks for your comment and kind words glad i could help , thanks for watching

[@fuckyou96]

Thank you fosho. Best video for this . I do have a question, did you put the old pulley on ? And if so can u use that puller tool to put it back on ?

[@lwaterman3505]

Good demo. Really liked that. Nice and straightforward

[@angelolivares5290]

Thank you for putting this video just did the job myself took me about an hour to finish thank you

[@ericduran3855]

This man is about to make me some moneyyyyyy 🛠😂

[@joepreziosi9817]

truly didn't expect you to answer thank you

[@anthonyowens2714]

Good video. On the road again

[@apacheone2000]

i have a '01 grand am gt 3.4 v6, i have a pully that squeals, i'm thinking its the power steering, as when the noise goes away the engine idles fine and i feel the steering is much lighter. than it was when it squeals. would the whole steering and pulley need to be changed?

[@njoeandjen]

Cool Video I have a 2000 century with same motor are these known to go bad mine seems noisy but no leaks first i thought it was ac clutch but guessing pump not real loud but definitely there!

[@ryans413]

This is a good motor the 3400 and the 3800 yea I know the headgaskets are an issue but just maintain the dam motor you won’t have an issue.

[@sugargoldy]

Good job young man I'm going to do that job this week

[@rocket41792]

Thanks Joe, you were very helpful. Do keep up the videos brother.

[@mshlw]

Hi JoeTheAutoGuy, Thank you for sharing your expertise... we appreciate you! My 2000 Olds Alero (2.4) power steering pump itself is fine, but the reservoir that holds the power steering fluid is broken & needs to be replaced. I have the new reservoir but am unsure how to replace just the reservoir tank. Any words of wisdom? Thank you so much for your time & help! HLW

[@joeyvig123]

Joe, was wondering if you could tell me what the black box/module is right beside the coolant bottle. Bought an 02 and I don't have that part. The pigtail is just hanging there.

[@JoeTheAutoGuy]

+joeyvig123 cruise control module

[@mrgiron53052]

great video and information!

[@stevewalther9965]

good vid...bummer you have to take motor mounts off.

[@johnwalton2272]

Great video, simple and helpful. Thank You!

[@jeezydb8507]

Just changed a buddies today and the new pump didn't have the electronic plug on it and the high pressure input was on the bottom of the pump. I think someone replaced the engine before he got it. He says it's a 1999 but I think the motor is either newer or older.

[@JoeTheAutoGuy]

if the pump has the variable pressure switch you have to adapt it to the new pump unless you ordered one without it

[@bananablood2031]

Man I am losing power steering when going through puddles, do you have any idea what that can be? I know that I am missing the little guard plate for the pulley but the fluid seems to be good. Thanks, great video man, keep it up.

[@JoeTheAutoGuy]

defintetly check your belt and tensioner for proper operation

[@jeezydb8507]

The old one had that switch but what autozone showed us and gave us for 1999 grand am 3.4 didn't match at all. The high pressure input is on the bottom and now he needs a new line bcuz the bend and angle of the metal isn't right.

[@JoeTheAutoGuy]

you need to take the snap ring off the switch and transfer it to the new pump then everything will line up the switch does not come with the pump

[@jeezydb8507]

Ok what about the high pressure line input not being on top

[@JoeTheAutoGuy]

as long as its the right pump for the variable assist then everything should line up there are two different ones

[@Morjesta]

I went to a shop to get my 2002 Oldsmobile Alero Pump repaired. I was told that the put me on a refurbished pump. But now i feel that the steering is way to soft. Even on high speeds. 60+ MPH the steering is way to soft. Is this normal? I feel i can easily loose control. Thanks for the help

[@brucegregory9712]

Followed your vid, it's pretty good. However I noticed you did not mention a small metal restrictor that goes into the low pressure return line. it is clearly visible on the unit you take out as it was left in the nipple of the old pump. I did not see it in the new pump when you put it on. (You forgot it?) It was just chance I saw this part on my 3.1 Malibu as it dropped onto the top of my engine..

[@JoeTheAutoGuy]

Bruce Gregory it was in place just hard to see in the camera. usually dont fall out but yes watch out for it

[@tonyequihua5736]

Very helpful advice and great video bud 😊

[@joetowers6591]

Hey Joe. Do you know of any videos showing how to rebuild this pump. If not. Maybe make 1 on it because I've looked everywhere and can't find 1. I think it would do well for you.

[@JoeTheAutoGuy]

I do not but that is a great idea for a video

[@joetowers6591]

@JoeTheAutoGuy i have to say. I like how you took your time and made it very easy to follow. But like myself I like to tinker with a lot of small things like this pump. I actually want to put new seals in it. I just think there's alot of other people out there with this pump and want to learn how to put seals in. Thanks for your time.

[@watchman1174]

Awsome video!!! Exactly what I was looking for.

[@JoeTheAutoGuy]

Roger Burnham glad i could help

[@mahadeva666]

my pump went out with a loud clunk and lost fluid immediately, do pumps make that sound normally ?

[@scottsullivan5716]

I would think the high air pressure evacuation of the fluid is not such a good idea and could potentially blow out one or more of the multiple seals in the system, i would skip this step and properly bleed the system if fully replacing the power steering fluid.

[@newfieledman9164]

Hello Joe why did you change the power steering in the beginning ,i have this issue with the noise problem is it cause of the cold weather that is causing this problem today it is -35 outside with the wind chill, or is it that there is Air in my lines of the power steering i removed the fluid the was in the pump and it was black, i didn't completely remove all of the oil if i give it a completely oil removal will the noise stop on my 03 grand am 3.4 liter. thanks.

[@MrLdspm]

Hey Joe, one more question. My Power steering pump pulley is too far out and is chirping. it's about 3-4 years old. is it safe to press it on a bit further?

[@steveburdette1808]

I have a 2003 grandam 4 cyl engine and the headlights quit however i can make them work by pulling back on the dimmer could it be the headlight switch or a sensor

[@pedromagpantay1834]

thanks ,joe for your videos

[@christopher5024]

how much fluid did you drain out of the system? im working on a 2008 Pontiac G6 and the pump seems to be the same i turned the steering wheel while having the return line disconnected and got some fluid while the engine was off and i got about half a Liter of fluid

[@Dgmstudios40]

You're a good guy Joe

[@lesliehayden2726]

have a question I have a 2005 Pontiac Grand Am and the engine blew and now I have a 2003 Pontiac Grand Am engine can that engine be replaced with a 2005 engine

[@alexvargas-rios6275]

Hey joe i realy like your videos you are a cool guy god bless you.

[@eyesonthefly]

is it necessary to flush the line? my car is squealing but i still got power steering (very smooth) but i was told it is the pump that it got worn out, is that possible? i did a video on my profile could you view it and give me your best guess.

[@johnnielsen82]

Great vid, thanks for making it man!

[@JoeTheAutoGuy]

+John Nielsen welcome , thnks for watching

[@Maxitikos]

Does one really have to bleed the power steering lines? There isn't much fluid in there. Wouldn't leaving the cap off of the power sterering resevoir and running the engine for about three minutes suffice?

[@JoeTheAutoGuy]

no air can be trapped and be harmful to the pump thats why its in the procedure ...people have done it and had luck though... just you might have jittery steering and such and it can really airate the fluid breaking it down over time faster

[@martinez1701a]

those are beautyful welds

[@richardsherman1685]

thanks 4 video have U changed rack&pinion on 2000 alero seems like weekend project

[@martinez1701a]

+Richard Sherman yeah it is basicly you unbolt the cross member from the bottom of the car to get to the rack and pinion kinda a pain, one thing to do when you bring it down is make sure you reinforce those brackets that rack and pinion bolt to. I had those break on two cars so i welded plates to them.

[@Abraham-gj5wr]

excellent video. very detailed. Thanks.

[@financeranger]

just what i needed, thanks. rented tool from auto zone and replaced my pulley while doing the pump since it was chipped. How long does it take to quiet down while bleeding air?

[@JoeTheAutoGuy]

i have a new video up for the bleeding procedure but if everything is done right it usually takes a couple of minutes 2-5 min but sometimes are stubborn and take awhile longer

[@financeranger]

noise is gone, now the rack is squirting fluid....gotta love cars with personalities!

[@MrLdspm]

Great job on the video. Only one question. How did you get the pulley back on the new pump?

[@JoeTheAutoGuy]

installer tool, sorry lost some footage on this one tried to get It done still

[@MrLdspm]

JoeTheAutoGuy thanks. I looked it up after I asked the question. ACDelco has a very good instructional video about pulley removal and installation.

[@MrKelso159]

You should try this on a 93 grand am gt. It's not as easy as this year model !

[@JoeTheAutoGuy]

MrKelso159 interesting ive never had to on the earlier models . might have to look into doing a video for one of those

[@MAGWolf]

MrKelso159 Do it on a Minivan version where engine is halfway into the cab.

[@UnKnowNxPeRsoN]

how did you install the old pulley on the new pump??

[@adreamuponawake]

I have a question, what size wood block did you use to support the engine? and where did you support it at on the engine?

[@JoeTheAutoGuy]

just a 7 inch section of 2x6 under the oil pan

[@user-zj1wn4fi5b]

Hey Joe I'm trying to find out where you got the power steering pump for the 2000 grand am video I'm having hard time finding the exact fit

[@JoeTheAutoGuy]

Some come with the variable steering effort solenoid some don’t , depends on which model you have , in my video it has the VSE valve so the pump I used was from Orielly auto Part # 734-70107P1

[@user-zj1wn4fi5b]

Thank you

[@yungog9098]

Yoo where did you get the power steering pump with variable effort? Cant find them anywhere.

[@JoeTheAutoGuy]

orielly

[@ryanpearce3528]

i have a question. what is that one red and blue plug because I'm swapping the power steering pump on my 2000 grand am and i have the red plug but there is no where to plug it in on the new pump

[@JoeTheAutoGuy]

+Ryan Pearce if you have the nv7 variable steering that has the connector you need to transfer over the solenoid

[@ryanpearce3528]

Ok thanks

[@justinmcmains4689]

Hey any idea on where to get one of those power steering pumps all of the ones I have been finding don't have a high pressure fitting

[@justinmcmains4689]

It's for a 2001 Pontiac Grand Am GT

[@JoeTheAutoGuy]

@@justinmcmains4689 www.oreillyauto.com/detail/c/masterpro-power-steering/chassis---steering/power-steering/power-steering-pump/3d51bc7abdc5/masterpro-power-steering-pump-remanufactured/mppc/73470107p1/v/a/4690/automotive-car-2001-pontiac-grand-am?pos=5

[@justinmcmains4689]

@@JoeTheAutoGuy Thanks been looking all over for it forgot about orileys

[@johnpaxton4743]

I have a 99 grand am all of sudden it starts running rough with no power and we drove it about 6 miles home after it started an the muffler or the pipe leading to the muffler under the car was cherry red . Can you give me any idea what it might be plz id so appreciate it

[@JoeTheAutoGuy]

you have a clogged catalytic converter for sure needs to be replaced and you need to figure out why it happened

[@non-descriptinfluence3112]

When your car is leaking power steering fluid, most time would it come from a faulty pump, or is the source somewhere else? thanks.

[@JoeTheAutoGuy]

it could be from anywhere , you need to locate if it the hoses, pump rack , but i see the low pressure hoses leak alot

[@non-descriptinfluence3112]

JoeTheAutoGuy Thanks for the response, Joe!

[@briannaviaux8842]

Hi there i am wondering if anyone knows if there is a video on how to remove a transmission on an 02 pontac grand am i am trying to do this myself thanks in advance

[@theroyalgamerz5864]

Joe i need you in my llife sir...seriously..lol

[@newfieledman9164]

how could i tell if the Alternator is giving a problem i've noticed that when i use my hazard lights i see the lights on my Dome light and Cluster and Radio are slightly Dimming.does that mean that my Alternator is bad. I had the Battery Checked it is ok.or is all the lights and hazard warning hooked into the same Circuit. thanks

[@JoeTheAutoGuy]

Newfie Led Man most likley the lights dimming is just a draw on the system (normal) its alright or a little dimming, if your alternator is not producing above 13.6 volts it could be failing but its always smart to check connections

[@newfieledman9164]

Ok thanks Joe I also know I am concerned about my power steering pump when its cold out it makes a loud noise and when the car warms up the noise goes away took her to my buddies garage today and we flush the power steering system the noise was gone away but we were parked outside for about 35 minutes and the noise was back a little Joe could too cold temperature cause this noise problem today it is minus 35 outside. Or is the power steering pump worn out .

[@JoeTheAutoGuy]

Natural wear of the pump will cause the pump to whine in cold if the noise goes away it's fine , I wouldn't worry about it when it's that cold the fluid greatly thickens and can cause the noise .

[@newfieledman9164]

Ok thanks Joe I will let you know we are going out later on it is a little warmer today sun is shining

[@wwmw51]

Wow! you didn't show how to install the pulley onto the new pump did you have to have it pressed on or what?

[@JoeTheAutoGuy]

i apologize i will make a video on that soon

[@rustywindsor8195]

"joe the auto guy" I got a question about a noise that's coming from the idler/tensioner pulley area

[@JoeTheAutoGuy]

+Rusty Windsor whats the question you have?

[@rustywindsor8195]

There is a noise maybe a bearing on one of the pulleys I think it's the tensioner pulley. It makes a clinking noise constantly. Do yu have Facebook I could send you a video tomorrow to show what it sounds like same cate 3.4 grand am 04

[@rustywindsor8195]

Same car**

[@JoeTheAutoGuy]

+Rusty Windsor Facebook page is joetheautoguy

[@Dubblesteel]

is there anyway to replace just the pulley, the one I'm working on has come loose.

[@JoeTheAutoGuy]

you can replace the pulley but if it came loose it could be the shaft runout or the pulley has expanded

[@Vater1]

Thank you

[@richardmueller9565]

ya didn't show how to put pulley on without damaging seals on pump!

[@MAGWolf]

Great video.

[@JoeTheAutoGuy]

+MAG “MAGWolf” Drago thnks!!!!

[@claytonatkinson865]

My engine is too close to the wheel well to fit a ratchet or breaker bar into the tensioner

[@ryans413]

Clayton Atkinson Do you have the 3400 or the 3800 the 3.4 motor you can get a small ratchet on the tensioner and move it just fine. On the 3800 little more difficult you gotta move some parts out of the way. I’d recommend getting a tensioner tool that’s more easy to use then a ratchet

[@stevedaniel2734]

Great video...

[@franka-pn7wi]

thanks how figure out of power steering pump smile ...

[@Unknowngaming141]

Very helpful

[@Bassplyr11]

What if I don't have that special pulley pulling tool

[@JoeTheAutoGuy]

if you dont have one you will need to get one , many stores have them available for rent or harbor freight tools or northern have them at cheaper prices 50 or less

[@djstatyk1540]

Is this the same engine in an oldsmobile alero?

[@JoeTheAutoGuy]

yes it is !!

[@Dubblesteel]

What's ur estimated time to replace P/S pump? Thx

[@JoeTheAutoGuy]

takes about 2 hours foughly if you havent done one before double that id say

[@ChadBlondiau]

thanks guy!!

[@JoeTheAutoGuy]

thanks for watching

[@trellgilbert6587]

What size wrench do i use to take the pressure side off

[@JoeTheAutoGuy]

Trell Gilbert varies but 15mm,16mm,or 18mm

[@hawknationwyatt4856]

Thanks 💯

[@Elchullaquiteno1]

hello does the new pump come with the connector ???

[@JoeTheAutoGuy]

doesn't seem to any more part ,needs to be transferred over

[@ej5240]

how do you replace the idler arm on 3.4 alero

[@JoeTheAutoGuy]

idler arm? do you mean the automatic tensioner?

[@mr.motormaster9881]

i thought you were gonna put a v6 super charged engine in a1991 G am

[@JoeTheAutoGuy]

Luis Rodriguez i beleive you have me confused with someone else

[@topherd1011]

Save yourselves the trouble and just buy a completed pump and pulley for like 30$.. Worth saving the hassle.

[@Elchullaquiteno1]

where did u buy the pump I can't find none with the connector

[@JoeTheAutoGuy]

sorry they dont seem to sell the one with the solenoid anymore you have to take it off yours and transfer it to the new pump i believe it the pump with the nv7 variable assist option

[@Elchullaquiteno1]

JoeTheAutoGuy is that what u did ??

[@vanilladiiip]

really good vid man! are u in canada ?

[@JoeTheAutoGuy]

united states why you ask? thanks for watching

[@vanilladiiip]

i wanted tackle the intake manifold on my malibu. i love the setup you have. this shop yours? my dream to have setup like that!! what past work experiences have you had that made you the mechanic you are? i work on reefers at a thermoking dealer ship but find my self way more interested in cars. im not afraid to do the big jobs. wish there was just more pay in automotive so much competitors. unless u build your own clientele....Anyways great work i would trust you to work on my cars any day! thats hard!

[@joewilson1522]

Anybody have issues with the new pump???? Ie. 2 of mine didn’t come with a sensor/connection needed to fit

[@JoeTheAutoGuy]

Require you to transfer it over now a days , there are some available with the sensor from Orielly auto parts

[@joewilson1522]

@@JoeTheAutoGuy thank you so much man I appreciate it

[@joewilson1522]

@@JoeTheAutoGuy is there any easy way to swap the sensor from one pump to another because mines pretty sure it wants to stay

[@joewilson1522]

Figured it out you need a 29-30mm socket to disconnect the fitting/sensor no need to remove any snap rings or anything

[@JoeTheAutoGuy]

@@joewilson1522 awesome it’s been awhile since i have done these

[@wadzaire]

Where Can I Buy/Order This Exact Pump ?

[@JoeTheAutoGuy]

bought mine from napa auto parts

[@xTHUNDERMAN73x]

Thanks for not showing how to reinstall the pulley.

[@JoeTheAutoGuy]

i state in this video that i had footage lost unfortunately , been meaning to do a video on this for awhile thanks for reminding me

[@jasonkeith965]

How do you transfer the connectors from the old pump to the new one?

[@everettbarrett9321]

How long did it take you to do this?

[@JoeTheAutoGuy]

about 2 hours to do the job

[@joetowers6591]

He didnt show how to put the pulley back on. If it dont come with 1.

[@JoeTheAutoGuy]

i did not i will have to do a video of installing the pulley thanks

[@joetowers6591]

@@JoeTheAutoGuy I don't want you to think I was downing your video or anything. It was freekn awesome and it was all i needed. So thank you for the information. 👍

[@jeezydb8507]

What year was this grand am.

[@JoeTheAutoGuy]

1999

[@Steadierpark]

Did I just see an electrical arc with batteries connected 🧐

[@JoeTheAutoGuy]

No?

[@Steadierpark]

@@JoeTheAutoGuy ok! There was blue flash or something. Sorry! Thanks for the video. My neighbor just had a leak on their alero ps pump from the sound of it. What did you use to support the engine underneath?

[@JoeTheAutoGuy]

@@Steadierpark took the front engine mount offf on this model its required or the engine will drop