porsche 996 alarm pin code extraction

[@talhawaseem5303]

Many thanks for sharing your experience with us, here is locksmith from dubai

[@PSICompanyPerformance]

Thanks for watching my friend. Good luck

[@AutoKeyMaker]

Good information 👍 😊

[@serafineightyfive]

thank you for this, this is easily the best video on this topic on YT :) quick question though: there are 4 "memory slots" for remotes and you showed, where the code for #1 starts. do you know at what addresses the other codes/remotes start? thank you in advance! ps: left a like and subscribed ;)

[@PSICompanyPerformance]

Thanks for watching. As soon as i get back to my shop i will give you the addresses for the remotes.. Thanks for the support to the channel.

[@arkezmeraj6912]

​@@PSICompanyPerformance Hello thanks for sharing this video, i am also interested where in the dump are other remotes located 🙏🏻

[@jacktingzon2378]

any update to where is the address of the other remote?

[@automotivediagnosticsrepai9006]

@@PSICompanyPerformanceI have question how much u charge me to edit my file so I can have obd acces if I send u file dump?

[@franklee9955]

Is that eeprom data dump file the only data you need to clone an alarm module? Ie if I re flash another module with the contents of that data, will it work in the car?

[@PSICompanyPerformance]

thanks for watching just copy the all dump from the original module to the donnor and thats it. good luck

[@guidojabreu]

I have a question, the 24 HEX code changes because it is a rolling code, how can you get that to be able to pair the remote, I did all the steps in the video and cloned my M534 perfectly, I extracted the 24 HEX from Line x0100 but what do we do with the rolling code that changes that I read are the last 5 characters of the 24 code

[@PSICompanyPerformance]

thats a very good question. i just read the code thats there and then i know thats the code the unit is expecting to receive so i program that but if it fails then you have to read it again and use the new code instead.

[@shaazy]

Thank you so much for posting this! Took me possibly an year of researching to get to understanding what I need to do get the remote to work again. I have a question, I believe my mechanic changed the transmitter inside the remote so its not the one original to car but he was unable to program. Would reading the code from eeprom get me the code to this replacement transmitter or the original one?

[@PSICompanyPerformance]

Thanks for watching The code in the eprom is from the original remotes... If you still have the original one , even if its not working, you swap the microchip with the other of the new remote and get it working with the original codes.. Good luck

[@shaazy]

@@PSICompanyPerformance By 'microchip' you mean the pill in the key fob, right? At this point, the key works to unlock manually and start the car. The fob unlock button blinks red when pressed. Let's say I read the codes via eeprom reader and use them to program the fob, is there a chance I could brick anything if the code I input is wrong?

[@erdemturan4517]

​@@shaazythe is pill is actually the transponder to start the car. There is another eeprom on remote PCB which not readable, but cointains the synch code. This one either needs to be your original transmitter or the code is known and printed by the OEM No way to retrieve the code from the remote itself.

[@cozmiccoz2195]

Hy! nice video, thank you! After done everything,do you use a normal diagnostic to learn the remote?

[@UA10i12]

Hello. If I am replacing my immobilizer, can I just replace the eeprom from my original to new module instead of going to dealer for reprogramming?

[@PSICompanyPerformance]

thanks for watching yes you can replace the eprom and be done. good luck

[@jeshv6888]

thanks a lot my friend, is any way to extract the pincode without swap the bytes ?

[@PSICompanyPerformance]

thanks for watching. sorry but no, unless you have a dedicated programmer, in that case it will read already with the correct orientation of the bytes.

[@chrisedwards3218]

How do you edit it manually so can access via obd? Completely stuck at this part.

[@eurowerx4267]

Hello Can I read the 93L366A chip and write it to the new module? Car run and keys work?

[@PSICompanyPerformance]

thanks for watching i never tried thatt but i almost sure that it wshould work just remenber to get the exact same part number to do that. good luck and lets us know if it works if you try it.

[@eurowerx4267]

@@PSICompanyPerformance yes sir, will do

[@eurowerx4267]

Vvdi prog would not write the file after saving the original. Would be the same data, wouldn’t ask for which file to write!!😢

[@PSICompanyPerformance]

@@eurowerx4267 did you desolder the eprom from the module? it better to remove it from the board and to make sure you have a good contact to the programmer, also make sure you select the right eprom 93c66a

[@SneekyFauker]

Hi friend! Amazing tutorial and the only one I can find on this. When I click on Swap Bytes L/H, nothing happens at all. Do you know what could cause this?

[@PSICompanyPerformance]

thanks for watching what software are you using?

[@simeonhadev4062]

He thank you for the video But i saw on vvdi its ask for learning passwords as well how i can find this ? Thanks

[@PSICompanyPerformance]

thanks for watching the learning pass is the pin code

[@wedolocksmithorlando]

@@PSICompanyPerformance sorry for bothering you the remote code this work just for the orginal remote or i can use this code to program new remote as well bec only remote available is used without the learn code

[@PSICompanyPerformance]

@@wedolocksmithorlando thanks for watching the code you see is for the especific remote that you are programming...that means that each remote should bring its own code...so i am guessing a used one is not your best bet unless there is a code with it

[@guidojabreu]

Hello, My IMMO M5340 was damaged by water, I bought a new M534 and cloned the EEPROM just like your video and everything worked correctly except the Remote is the only thing I couldn't get to work, do you have an email to share information about this? thank you so much

[@waldemarfechtel1644]

Thx for video!?!

[@inventor34]

😮I congratulate you my friend, thank you very much for the good information you gave. I have a 2000 Porsche boxster s vehicle, I use piwis 2, I want to reprogram the vehicle's DME and change the map. piwis asks me for the programming code, where can I learn this code? I did all the flash readings from the ECU. Is this code registered in the ecu or in the m534 unit?

[@PSICompanyPerformance]

Thanks for watching. Its in the m534 unit my friend. Good luck

[@inventor34]

@@PSICompanyPerformance thank you very much friend

[@piwistester4225]

hello mate please do you have mail ?best regards

[@PSICompanyPerformance]

Thanks for watching. Please post yours and i will contact you. Thanks