Portable and Compact Telescoping Fishing Poles For Ham Radio - Goture Goldlite

  Рет қаралды 18,896

HAM RADIO DUDE

HAM RADIO DUDE

Күн бұрын

Пікірлер: 61
@loraz0
@loraz0 2 жыл бұрын
I found the "Miracle grow super steel garden stake" fits inside perfectly. They are 6 feet long, tubular steel with plastic covering. I use a 2 foot section, push 1 foot in the ground, and slide the pole on the other foot. I left it up in 40+ mph winds for a day, and it stayed up great.
@IrregularInterest
@IrregularInterest 3 жыл бұрын
I've also been waiting on a Carbon 6 for months, so this video is hugely appreciated. Will definitely check out the Goture.
@roadie6153
@roadie6153 3 жыл бұрын
Great idea. I use a tiki torch stake for backpacking. Very light aluminum with a thumb screw to tighten down any diameter pole, whether a fishing rod or Carbon 6 mast.
@HAMRADIODUDE
@HAMRADIODUDE 3 жыл бұрын
I kind of like that idea. I may get a pack of those to test them out. They look a lot less like a prison shank (in case I get pulled over or something). Thanks for the input!
@Wildhare-uo5vj
@Wildhare-uo5vj Жыл бұрын
You need to measure your poke when it's assembled. They get their measurements by adding the total length of each piece and giving you the sum. When I got my rod, it measured 18'6. They don't factor in the length lost length of each piece when a little of each piece is inside the last one. By the time I removed the top two pieces it was under 14'.
@HAMRADIODUDE
@HAMRADIODUDE Жыл бұрын
Thank you
@paulhastings3109
@paulhastings3109 3 жыл бұрын
Looking good will be checking it out 73 Dude
@HAMRADIODUDE
@HAMRADIODUDE 3 жыл бұрын
Thanks Paul! I hope you enjoy!
@Siskiyous6
@Siskiyous6 3 жыл бұрын
I missed this during hunting season, thanks for pointing it out to me DUDE! Spike nails are dirt cheap and will do what you are doing there.
@HAMRADIODUDE
@HAMRADIODUDE 3 жыл бұрын
Hey, no worries. I the k8mrd has a few videos on similar stuff. I can't wait for warmer weather so I can get to outdoor recording again
@wa7jnjradio
@wa7jnjradio 2 жыл бұрын
After leaving one of my poles on a summit, looking for a replacement...and nice to see this Amazon one as an option! 73
@alanb76
@alanb76 3 жыл бұрын
Good short video. Always good to have another option with more available components, especially in the current supply chain situation. The off white pipe looks like CPVC which is used for hot water whereas PVC is only rated for cold water. Electrical tape is good, or 3d print some adapters. I made some similar adapters for the larger telescoping poles with a trailer hitch and some all-thread layered with PVC and tape for quick stationary vehicular deployment (before I had a 3d printer). Lots of useful ideas. :) 73 de w6akb.
@HAMRADIODUDE
@HAMRADIODUDE 3 жыл бұрын
You are correct Alan! CPVC! I have this cool 3d printed "connector" or "Separator" designed. Hopefully if I get a few moments, I can go test it out, but it's super simple and prints in about 35 minutes. I'll be happy to share it when I confirm it's working. This is my favorite part of the hobby. Finding things that will work, and designing others that will make those things work better.
@potaactivator
@potaactivator Жыл бұрын
This is exactly what I need for POTA. Thank you.
@HAMRADIODUDE
@HAMRADIODUDE Жыл бұрын
My pleasure. Another good one that I've had success with lately is the South bend kwikstik. 17 ft and it appears to be better build quality with a tad more rigidity
@potaactivator
@potaactivator Жыл бұрын
@@HAMRADIODUDE I actually searched for that one a few days ago and could not find it in stock anywhere.
@HAMRADIODUDE
@HAMRADIODUDE Жыл бұрын
@@potaactivator this is an affiliate link, but this is the one I have, the only thing I would recommend is not opening it by sitting it out like a fishing pole as the sections tend to get stuck together. amzn.to/3KIPXNk
@HAMRADIODUDE
@HAMRADIODUDE Жыл бұрын
If I can get my garage finished cleaned before I leave Tuesday, I'll try to make a quick video comparing about several different crappie poles
@lyledal
@lyledal 3 жыл бұрын
Very useful vid! Terrifying amount of whipping it out though! 🤣
@HAMRADIODUDE
@HAMRADIODUDE 3 жыл бұрын
Oh yeah, I need to watch my choice of words. :)
@brentjohnson6654
@brentjohnson6654 3 жыл бұрын
Very nice. I am looking for a portable pole for maybe POTA and this gives me some ideas. You are very clear to me and I will keep watching this channel for more content. 73 de KI5HXM
@HAMRADIODUDE
@HAMRADIODUDE 3 жыл бұрын
I really appreciate that. I do my best to make things easy for everyone to understand. Let me know if you come up with any other cool ideas or find a pole you enjoy. So far, I have brought this out a few times and it's done a real good job. One thing I did: I used the smaller off yellow tubing and placed some heat shrink around it, then taped it. I did this after I let the epoxy fill up inside the tube. It looks a lot cleaner and seems to grip the inside of the pole a little better. Thanks again!
@truck57us
@truck57us 3 жыл бұрын
Nice video. I have been using this pole for a 2m/70cm roll up slim jim (ladder line) antenna and RG8X coax for over a year. Super easy to carry and deploy as shown.
@HAMRADIODUDE
@HAMRADIODUDE 3 жыл бұрын
I think that I may get a slim jim (or build) ladder line antenna for just that. Thanks for the input. Glad it is working well for you!
@submarineradioman5535
@submarineradioman5535 3 жыл бұрын
Nicely done!
@HAMRADIODUDE
@HAMRADIODUDE 3 жыл бұрын
I appreciate it, thank you!
@submarineradioman5535
@submarineradioman5535 3 жыл бұрын
@@HAMRADIODUDE a lot more convenient than the bronzed steel 33’ telescoping whip I used to drag up through the conning tower to the bridge at sea!!!
@stevenemert837
@stevenemert837 3 жыл бұрын
Is that a Knight Kit Star Roamer in the background? I'm jealous.
@HAMRADIODUDE
@HAMRADIODUDE 3 жыл бұрын
I got it at a church rummage sale for a buck or two :) Thanks!
@don_n5skt
@don_n5skt 3 жыл бұрын
Those poles work great for building a Moxon like Chuck has. ;) Did you try using end caps on the 1/2 pipe? I have many Carbon Fiber masts and if you run a wire buy it or coax down it, no issue. I have used ladder line next to it at 3" out from the pole with no issue.
@HAMRADIODUDE
@HAMRADIODUDE 3 жыл бұрын
Hmm, I did not try the end cap, but that is worth a shot! Thanks Don! As for the moxon, I love what he did. We had the Moxon up and operational within 10 minutes, I would say. Nice poles to have around.
@themasterhammer
@themasterhammer 3 жыл бұрын
That off colored pipe is called CPVC.
@HAMRADIODUDE
@HAMRADIODUDE 3 жыл бұрын
Thank you!
@jbaker389
@jbaker389 2 жыл бұрын
Any reason you couldn't attach the pole to a tripod with something like a "CAMVATE Super Clamp Articulated Mini Ball Head with 1/4"-20 Thread Hole" and stake/weigh the tripod down to get things just a little higher since your not using the end lengths?
@503Nick
@503Nick 3 жыл бұрын
I literally got my SOTAbeams 6M carbon last week and ordered it less than 2 weeks before that
@HAMRADIODUDE
@HAMRADIODUDE 3 жыл бұрын
Where from
@HAMRADIODUDE
@HAMRADIODUDE 3 жыл бұрын
DX engineering is showing out until December
@johnb6084
@johnb6084 Жыл бұрын
It looks like that rod might fit in a spiral fishing rod holder, Walmart sells the Ozark Trail rod holders for less than 3 bucks. What's the diameter of that rod at the base? I measured the inside diameter of the rodholder with calipers and they are about 31mm.
@HAMRADIODUDE
@HAMRADIODUDE Жыл бұрын
Off hand I don't know the diameter, but it does fit in the orange fishing pole holders from Walmart
@johnb6084
@johnb6084 Жыл бұрын
@@HAMRADIODUDE Thanks for the response. That's what I have, the orange sturdy rod holders. It looks like I might have to buy the rod and give it a shot.
@HAMRADIODUDE
@HAMRADIODUDE Жыл бұрын
If you have a few days/week, I'm working on an update video / comparison
@johnb6084
@johnb6084 Жыл бұрын
@@HAMRADIODUDE Perfect, thanks
@ronrico2620
@ronrico2620 Жыл бұрын
The link for this pole has multiple colors for different prices. Is there any difference in the strength or are they all same? This radio hobby isn't cheap and I'd like to save when I can
@mikebohemia1947
@mikebohemia1947 2 жыл бұрын
Thanks, really useful. 73.
@hikingfish3
@hikingfish3 2 жыл бұрын
I was just looking at these fishing poles on amazon. Great video! Would these work with a slim jim (N9TAX) antenna or would they cause interference?
@HAMRADIODUDE
@HAMRADIODUDE 2 жыл бұрын
That's a great question. The potential is there as it is Carbon Fiber. i guess I could make one, but it would be a few weeks.
@hikingfish3
@hikingfish3 2 жыл бұрын
@@HAMRADIODUDE I'd love to see that video if you can do it! Kudos for the channel
@davlanders2
@davlanders2 Жыл бұрын
You can get a signal through but there is some interference.
@burkhardgerken4205
@burkhardgerken4205 2 жыл бұрын
What's the name of the camera bag?
@HAMRADIODUDE
@HAMRADIODUDE 2 жыл бұрын
Good day! It is a bag for my bicycle: pedegoelectricbikes.com/product/pedego-trunk-bag/. Have a good one!
@seanfoley7097
@seanfoley7097 7 ай бұрын
I'm on the third floor apartment when the landlord won't let me throw a wire to a tree so I got one of these with the idea of putting my 66 ft of wire through the end of it and stick it out the window so it's away from the house and hanging straight down with the wire coming in down the pole into my radio and when I'm done playing radio I'll just pull it back in
@barrykelly2722
@barrykelly2722 Жыл бұрын
So many innuendos possible but I will refrain. Lol
@kylefreemason
@kylefreemason Жыл бұрын
Do you still recommend this ?
@HAMRADIODUDE
@HAMRADIODUDE Жыл бұрын
I like this one. Have a good one kzbin.info/www/bejne/iaGaeYiEaMpgd80
@nerdlywehunt
@nerdlywehunt 2 жыл бұрын
Just fyi, kickbacks are illegal in the eyes of the IRS but affiliate links or online review compensation is legit.........
@HAMRADIODUDE
@HAMRADIODUDE 2 жыл бұрын
I'm not sure I understand what you're trying to tell me here..nor if it has anything to do with more or rather how how the system works? Thanks
@jasonpeterson3214
@jasonpeterson3214 3 жыл бұрын
Dude, I was scanning the tube on antennas and this one popped up kzbin.info/www/bejne/rYfYaWtvZ915oZI I watched it ant was on pins and needles through most of it. Your video also popped up so here I am. I watch and give thumbs up but as a rule don't comment. Now I will finish watching your video. lol
@Screamingtut
@Screamingtut 3 жыл бұрын
second
@HAMRADIODUDE
@HAMRADIODUDE 3 жыл бұрын
Thanks for watching. Wishing you the beset, Kristyanna
@enginedave
@enginedave 8 ай бұрын
Harbor fright
Spiderbeam 12M Telescopic Mast Review
17:56
Ham Radio Portable
Рет қаралды 28 М.
How To Use a 17 Foot Telescopic Whip for Ham Radio
7:29
COASTAL WAVES & WIRES
Рет қаралды 56 М.
My scorpion was taken away from me 😢
00:55
TyphoonFast 5
Рет қаралды 2,7 МЛН
Mom Hack for Cooking Solo with a Little One! 🍳👶
00:15
5-Minute Crafts HOUSE
Рет қаралды 23 МЛН
We Attempted The Impossible 😱
00:54
Topper Guild
Рет қаралды 56 МЛН
Goture Capella Tenkara Rods
16:14
Burning River Bushcraft
Рет қаралды 3,7 М.
3 Masts Everyone Needs for Ham Radio
6:10
KM4ACK
Рет қаралды 45 М.
Which Pole do you need for Ham Radio?
14:50
MM0OPX Field Radio
Рет қаралды 20 М.
How to Properly Extend and Close Your Telescopic Fishing Rod
9:10
High Altitude Brands - Fish More, Fish Easier
Рет қаралды 29 М.
I Bought Amazon's BEST RATED Telescopic Rods!
13:33
FISHERYIN
Рет қаралды 166 М.
#005 - Telescopic Carbon fiber rod - Goture Breeze 5.4 m - Fishing  Test
6:13
Xie Xie - You are welcome!
Рет қаралды 12 М.
You WANT this portable HF MAST in your kit | K7SW Ham Radio
11:11
K7SW ham radio
Рет қаралды 33 М.
Review: Goture Collapsible Carbon Fiber Rod
7:38
Jungle Explorer
Рет қаралды 28 М.
My scorpion was taken away from me 😢
00:55
TyphoonFast 5
Рет қаралды 2,7 МЛН