power board connection wairing 16 amp#electricalshorts
Пікірлер: 71
@mdmuneerkhan5858 Жыл бұрын
Wire Galat use Kiye ho Neutral ke liye Black Use karo Aur Fase ke liye Red you Understand
@user-yx8yk3vu3uАй бұрын
Bhai not a 16 mpier its correct 15 mpier and use two clour wires..
@shantharajshanthraj3364 Жыл бұрын
Indicater is directed here
@bilalahmedmustafa2286 Жыл бұрын
Loose terminal connection...he doesnot fix it
@pankajsaurashtriya37895 ай бұрын
Resistance kitne ohm ka lagaya hai
@beautifulworld1491Ай бұрын
100 kilo ohms half watt
@shashipalgavitvlog44376 ай бұрын
Red 🚨 on hi rehti hai😂😂
@anandhavanandhav4877Ай бұрын
Tq bro❤
@jaijaibhardwaj9663 Жыл бұрын
Thankyou sir
@Pradeep..29093 ай бұрын
Thanks Bhai
@RK-pi1kr2 ай бұрын
Grounding left the chat
@javedkapoor5330 Жыл бұрын
Thank you
@komal7929 Жыл бұрын
Bhai4 5pin do 2pin ki vayring karo
@ravietc Жыл бұрын
Ok bhai apko jawab juld mil jayega thankyou
@candyvlogs15 Жыл бұрын
Wrong connection in indicator it will blow just when switch on
@surajit2570 Жыл бұрын
😂😂bebakoof 😂😂dhyan se dekh lo
@Joker-sm7ji5 ай бұрын
Abey indicator direct hai phase neutral pe
@arjunsachan461211 ай бұрын
ragistance kitne om ka hain
@madancreativeideas2095 Жыл бұрын
Power connection right side
@Jitendra42225 ай бұрын
Good
@SaurabhTotalVlogs123 Жыл бұрын
Thanks bro
@Vikeshbhore8 ай бұрын
Bsdk galat condition hai
@mazharbaig304611 ай бұрын
It's right connection😅😅😅😅
@user-ks2fe8cw9j4 ай бұрын
❤❤
@haider20459 ай бұрын
indicator ka conection aisa rakho swith on krne pe jale
@Joker-sm7ji5 ай бұрын
Zaroori nhi hai...ek hi baat hai
@Lachkeoelectric6018 Жыл бұрын
good dear
@afoodkitchen749410 ай бұрын
Led wire wrong canection.😅
@balajibaromoja2758 Жыл бұрын
BY nice Led
@loverofthelostnarc Жыл бұрын
The LED has no rectifying diode. In short the LED will dim or blow off.
@Joker-sm7ji5 ай бұрын
Then how to connect
@loverofthelostnarc5 ай бұрын
A rectifier diode (1N4007) should be connected in series with the LED along with the dropping resistance, only then your LED will last for a long time, because an LED is a DC component with a PN junction and so it needs a rectified AC which is rectified by the 1N4007 plus your voltage dropping resistor. For example : Line voltage minus ( led voltage plus diode voltage) 230 - (1.8 + 0.7) = 227.5 227.5 ÷ 0.02 = 11.375 ohms 0.02 ( 20 ma ) is the current needed to drive the LED 11.375 ohms is irregular value of the resistor. The standard value is 12 kilo ohms. So 227.5 ÷ 12 k ohms gives 0.0189583333 Amps which when converted is 18.95 mA, that gives us the safe value to drive the LED for a long time until voltage fluctuations damages the LED. I think this is enough working theory and procedures for you. Love from Mumbai ❤
@Joker-sm7ji5 ай бұрын
@@loverofthelostnarc are you electrical engineering
@loverofthelostnarc5 ай бұрын
@@Joker-sm7ji I have done radio engineering in 1982. So every little current and voltage drop should be respected. You should should not leave any room for plus/minus in calculations. Resistor are already marked with percentages of the values. For example standard resistor of 220 ohms with percentage of +/- 5% is 231 ohms or 209 ohms. Check this out with a True RMS Multimeter.
@Joker-sm7ji5 ай бұрын
@@loverofthelostnarc so isn't it same to connect the led directly or on switch
@user-xu7pf2ij7h Жыл бұрын
❤❤❤
@user-on4dt4jj1v10 ай бұрын
Mera blast ho Gya 😭😭
@Dilshadkhan_mn5 ай бұрын
Are yaar mene lagaya to thodi der chala fir band hogya ya kya hua tubelight chal rahi hai bord kaam nhi kar raha ek me current aarha hai ek me nhi mene tester se chek kya tha ❤
@ravietc5 ай бұрын
Ghar ki waiting chack karen nutal nahi aa raha hai thankyou
@skkaja5139 Жыл бұрын
👍
@user-uz4lx5ju4o5 ай бұрын
ಬ್ರೋ ತೆಕ್ಸ್ ❤❤❤
@jatavraj6403 Жыл бұрын
Hiiii
@user-vr6zg1wu9n9 ай бұрын
interlaw
@simplemanindian6885 Жыл бұрын
How many ohm resistor?
@razzvideocreation2865 Жыл бұрын
100k
@electricworkskill Жыл бұрын
KY Kar raha he
@balajielectricals3907 Жыл бұрын
ब्लू और लाल दोनों फेज के तार है। आपने गलत दिखाया है