Great video, you are the first guy I have seen that did it the right way.
@slagletoby Жыл бұрын
Sweet boat and I’m sure your grandfather is happy that you have it as he looks after from above ❤️🙏 Thank you for posting and this vid is very helpful. Stay awesome!
What a beautiful old boat, and with your know how it should stay that way.
@GenericUserUnknown11 ай бұрын
Thanks for taking the time to create and post this video. The level of detail is great.
@ProjectComplete11 ай бұрын
Glad to hear it helped!
@gregkrugman30352 жыл бұрын
Finally somebody with a video on the exact type of unit that I have to which I can see the shit that I thought was going to be needed is needed. I appreciate the video
@ProjectComplete2 жыл бұрын
Glad it helped you! That’s why I make my video. I just uploaded a video on the lower gear unit oil as well. Check that out too. It’s an important part of maintenance!
@MHFROX2 жыл бұрын
Great tips! Love the old Glastron! We had one when I was kid (60's) and you just don't see 'em around much anymore! I guess they're still building them but they have changed the iconic paint scheme a bit. Again, great tips!
@bouldernelsonbigfoot Жыл бұрын
Love the Orange and the Old Boat ,sweet.
@ronpassmore7053 Жыл бұрын
Thanks for the great instructions! Exactly what I need ...... as soon as Hillary passes through.
@raifcrosley15811 ай бұрын
That was the perfect video that's exactly what I needs to see I'm about as green as the grass when it comes to these boats LOL thank you thank you very much and looking forward to more helpful hints.
@ProjectComplete10 ай бұрын
Glad I could help!
@jenniferhatfield14682 жыл бұрын
Hwy, Thanks! I just took care of my Johnson 140. Works great. Loved the clear camera shots.
@ProjectComplete2 жыл бұрын
Thanks!
@gordonpeden62342 жыл бұрын
Nice one mate! My 85 HP Yamaha tilt trim played up today. I was gunna' check our crab traps. & at the ramp the motor wouldn't go down. The hydraulic pump is running , and eventually dropped. I thot' lack of fluid! I know it's an Evinrude/Johnson but it is exactly the same as the Japanese rip off. I appreciate your vid especially the ATF fluid.
@ProjectComplete2 жыл бұрын
Glad I could help! Thanks for the comment. Hope you got it all figured out!
@keithoszmanjr48023 жыл бұрын
nice job on this video! the info and camera work was great!
@ProjectComplete3 жыл бұрын
Glad you enjoyed it!
@carlabrone003 жыл бұрын
Helped me out big time thanks... I was stuck in the up position. Notice I WAS lol thanks again
@ProjectComplete3 жыл бұрын
Glad it helped!
@rayz79982 жыл бұрын
Thank you. Keep up the good work. You've saved me a trim change .
@victorjoseph10313 жыл бұрын
Thanks a lot ...that really helps me a big time.
@ProjectComplete3 жыл бұрын
Glad it helped!
@twr41cox2 жыл бұрын
Nice tutorial. That boat is mint!
@ProjectComplete2 жыл бұрын
Thanks!
@leshamilton66572 жыл бұрын
Awesome brother! I have the same motor so I will be watching and probably reaching out for help! :) Thanks!
@Papapickles69 Жыл бұрын
Appreciate the upload man, beautiful boat brotha.
@andygilbertson8925 Жыл бұрын
Awesome vid bro..... Your just saved me alot of money! Keep up the good work, sweet boat by the way!!!
@ProjectComplete Жыл бұрын
Thanks! Glad it helped.
@henrytaylor26382 жыл бұрын
Thanks! I'm about to tear into my 125 horsepower Force for the same problem... The shop told me they couldn't rebuild the pumps and it would be 6 or $700 for a used replacement unit...
@Sphere36019763 ай бұрын
Thank you! This was very helpful!
@bobpike67272 жыл бұрын
Hey bro. I have a mercruiser outdrive that is partially up/down. I'll do my best to apply your teaching in this video. Thanks for sharing!
@ProjectComplete2 жыл бұрын
Glad it helped! I believe most units have a manual release. So check into yours, I’d start with trim and tilt fluid and then move on to seals and rebuilding. If your hearing no motor pumping or trying to pump. That may be gone as well. Best of luck to you!
@paulkim17632 жыл бұрын
Good. Thank you.
@garycoutts68213 жыл бұрын
Awesome thanks for the video all the best from the land down under
@ProjectComplete3 жыл бұрын
Glad it helped!
@jimmyboe253 жыл бұрын
lmao the intro was gold
@graves0083 жыл бұрын
thank you wasn't sure if i needed to put the plug in after i filled it before cycling
@ProjectComplete3 жыл бұрын
Glad it helped!
@tuckerfetzer18293 жыл бұрын
My system is a little different but it definitely sounds like that. I didn’t know if I should leave the cap off or not because the fluid was pouring out lol.
@ProjectComplete3 жыл бұрын
I don’t know your exact system, but generally during the flush part you leave the plug off. Fluid is supposed to come out during the flush. Once the lines and cylinders are clear of most of the air, then the final part is fill the reservoir to the max fill. The whole process is very similar to bleeding brakes.
@terrymoore4786 Жыл бұрын
Well done video, thank you
@frankrodriguez4720 Жыл бұрын
Thanks for the tip. It worked for me.
@ProjectComplete Жыл бұрын
Glad it helped you out!
@wg88472 жыл бұрын
Good job brother.
@acordboy2 жыл бұрын
thank you sr! very helpful!
@franciscoadolfo58059 ай бұрын
Nicely done
@ronpassmore7053 Жыл бұрын
Do you happen to have a video on how to replace the trim motor (in case that is what I need to do)? I loved your video as I have an Evinrude VRO 140 (1985) (On a Glastron), so it looks very much like your boat engine.
@ProjectComplete Жыл бұрын
No I don’t sorry, I’ve never had to replace mine.
@Chrisgreece552 жыл бұрын
nice job ,nice explain!
@guglielmodicarlo41392 жыл бұрын
fyi if you dont have that special tool, you can use the blade from a dull chisel or screw driver and hammer the small holes in the losen direction to remove and tap it off and on, same as the old school sttuts on a car,
@gregtheboatman5212 жыл бұрын
Beautiful Glastron
@ProjectComplete2 жыл бұрын
Thanks!
@danielmckeen2465 Жыл бұрын
Nice video Bro!!!🤓 Thanks!!!!
@ProjectComplete Жыл бұрын
Thanks glad it helped!
@hikingsteven76653 ай бұрын
thanks that was helpful beutiful boat yo have
@tuberOOSKI Жыл бұрын
Well done and very informative. Thank you! What is the approximate fluid capacity?
@ProjectComplete Жыл бұрын
Sorry I don’t remember. I believe it was about 1.5 quarts I used, but it also loses fluid in the fill process.
@tuberOOSKI Жыл бұрын
@@ProjectComplete Thank you
@truestoryz Жыл бұрын
good video thanks
@rafaelsuazo83292 жыл бұрын
Great video. thanks!
@ProjectComplete2 жыл бұрын
No problem, glad it could help you!
@waleedamoun67962 жыл бұрын
nice and clear. .. but I saw another vedios tit the scrow
@pavloskourris2779 ай бұрын
great
@caetanon5756 Жыл бұрын
maravilhoso vídeo!
@raymorris21092 жыл бұрын
Good job man
@ProjectComplete2 жыл бұрын
Thanks, glad it helped!
@gregdeguzman-ff7sz Жыл бұрын
thank you i can fix my motor now save me some money yeah
@AsukaYenOSRS3 жыл бұрын
Very helpful. Question that maybe you can answer? My fill screw seems to be rusted tight. Any ideas on how to free it up? 1988 Johnson 88 SPL motor. Motor mount looks exactly like yours.
@ProjectComplete3 жыл бұрын
Try PB plaster and an impact screwdriver, but the chances are the fill screw will be damaged. Heat can sometimes work, but there should be a rubber gasket. So if you do use heat you’ll want to replace the screw and gasket.
@scottmichael3745 Жыл бұрын
@@ProjectComplete PB really is the best penetrant. And very good advice. I've been am mechanic for over 30 years and I would have given the exact same advice.
@mr2nr2 жыл бұрын
Nice tutorial but for future videos when your trying to show air noise in the system you might want to nix the music lol.
@SDADDYWSL1TR3Y Жыл бұрын
My 1979 85 hp seals are leaking I can’t find the part and I’m not sure if that’s the proper term for the part? My mechanic can’t find any online but he said if I find the parts I could do it myself , can you help identify the part for me? It’s the circle thing with the 4 holes in it , he said that’s all I need to replace
@bongo042 Жыл бұрын
It would've been nice to see how you removed the pistons.
@ProjectComplete Жыл бұрын
To remove the pistons. You use the pronged tool to remove the caps and they just slide out. There is nothing that holds them in other than the cap and o ring around the piston. Hope that helps!
@tonylock77662 ай бұрын
I'm at seal kit do they contain the seals for the center hydraulic cylinder we have one from the same year bought that exact kit and it did not contain the main cylinders seals
@ProjectComplete2 ай бұрын
I believe they include the seals for everything in the hydraulic trim and tilt unit. But I’m not 100% sure. I didn’t end up using all of the seals in the package.
@chriscraft4108 ай бұрын
What tool did you use?
@999gloryhog3 жыл бұрын
This was a very informative video, thank you. My motor won't go down unless I open the side screw. However, the two lower pistons won't go down at all. Any thoughts?
@999gloryhog3 жыл бұрын
It will go up though. Is there just one motor for both up and down?
@ProjectComplete3 жыл бұрын
Usually it’s one motor for the whole system. What you mentioned above is why I replaced my seals. Start with making sure the pistons aren’t seized and then replace seals and fluid.
@999gloryhog3 жыл бұрын
@@ProjectComplete thanks. I was able to get it to go up and down by leaving the fill cap off, backing the relief screw out to lower it and lowering it. Then lraising it. I did this a few times and it would go down.
@kharesettle66022 жыл бұрын
bet thanks bra
@DGOUTDOORS012 жыл бұрын
I will gave to give this a try. I'm tired of doing it manually letting down and lifting up the motor. And also a question what do I use for lower unit to fill the gear oil?
@ProjectComplete2 жыл бұрын
Yes, that hydraulic system was actually from a another boat of the same year. Before it was just a manual trim tilt system. I had to wire everything from scratch from relays and fuses. It’s funny you mention lower gear unit. My next video is on lower gear unit maintenance. I typically use 80w-90 gear oil and change it once a year unless your noticing water getting into it.
@jasonfrenchsr Жыл бұрын
my trim sounds like the pump is working but it won’t raise or lower at all, just makes noise and it’s full of fluid . could my seals be blown in my pistons ?
@ProjectComplete Жыл бұрын
Yes, it’s possible the system is not holding pressure. It’s also possible that your pump is trying to pump, but not actually working.
@nicolebraxton6273 Жыл бұрын
If we just bought the boat and lost contact with the previous owner how would we know what fluid is in there?
@ProjectComplete Жыл бұрын
You don’t but, it’s not like an engine oil change. If it were me id try to drain as much as possible and replace. If they did it the correct way they should have used hydraulic fluid.
@omarvaldez8080Ай бұрын
Buenas noches,con una duda por qué mi trim golpetea el motor cada. Vez que lo bajo,gracias
@ProjectComplete26 күн бұрын
I dont know what you mean by "hit the engine". Can you provide more description?
@omarvaldez808026 күн бұрын
@@ProjectCompletegracias por tu respuesta,me refiero a cuando el motor está en la posición de arriba,al bajarlo con el trim hace movimientos bruscos,da muchos brincos!!!!
@jims4539 Жыл бұрын
Have similar trim/tab that all wires were cut -any way you could for quick talk? Thanks.
@ProjectComplete Жыл бұрын
Message me on Instagram. Hit the follow button first so the message comes through. instagram.com/project_completed?igshid=YmMyMTA2M2Y=
@numbedbyreality Жыл бұрын
It looks like you have an orange strap around the lower end while you have the engine up. Is that for extra safety? What do you strap it to?
@ProjectComplete Жыл бұрын
I only did that to remove the pin to the center hydraulic. It was attached to a beam on the exterior over hang of the house. It allowed me to raise and lower the motor without a second hand and get fine adjustments to reinsert the pin. If you are not replacing seals you don’t need to remove the pin or detach the hydraulic from the motor mount the standard safety catch on the motor is all you need. When you have to remove the pin, the motor has to raise past the safety catch. I just didn’t want it slamming back down on the safety catch when the pin get removed. When you are just checking and refilling fluid the motor needs to raise and lower freely.
@GmailGmail-gg8lt10 ай бұрын
i just finished refilling the unit and changing the seals. the seals seem to be holding, the pump runs, there's power to the button, but the motor wont go up or down. i can feel pressure building in the pistons, because there is resistance, but i am at a loss as to why it wont pressurize and function. any thoughts?
@ProjectComplete10 ай бұрын
Can you manually raise and lower the motor. If not the pistons may be seized and/or the rebuild/gaskets were done wrong. If you can manually raise and lower. The pistons aren’t seized and the hinge point may be. I’d try disconnecting the piston from the motor and see if they move. If the do and your motor hinge point is not seized. Your pump may be acting up and not providing enough power to get the motors weight up and down. I’d start with check oil and going from the top of this message through the rest.
@GmailGmail-gg8lt10 ай бұрын
Yes, i can raise and lower it. I'll need a had to remove the piston and raise and lower it, but i think it will move. I released some air and think i may have released too much oil in the process. The pump is making some weird noises now, but it seems odd to have been working fine before the project and now...failing. but i guess everything has to break at some point. thanks for the feddback. i'll let you know what happens once i disconnect the piston@@ProjectComplete
@ajapsandali2 жыл бұрын
Sometimes my engine goes down on its own…. Not all the time but it should always hold up. Any ideas? Could I be low on fluid?
@ProjectComplete2 жыл бұрын
If we’re talking about a slow drop or “sag”. I would guess a seal leak or low fluid. I’d start with check levels. Best of luck!
@xaristr2646 Жыл бұрын
Hi man, my boat yesterday the trim tilt was working, and the next day I went to do some check the only think I can hear is noise and the trip tilt is not working, the engine is not going up or down, but the noise sounds like your boat when air was in there. What you suggest to do?
@ProjectComplete Жыл бұрын
I’d start with checking/adding fluid. If that doesn’t work you may have a problem with your pump, but I’d start with the oil because it’s cheaper.
@phongphungba76574 ай бұрын
Máy Yamaha 60 bên xuống không hết là bị gì
@kburns6282 жыл бұрын
If the caps are corroded to no end what’s the best way to remove them. Holes on the caps are shallow and brittle when I use that specific tool
@ProjectComplete2 жыл бұрын
Well, I would start with a wire brush and good soaking of PB Blaster, let it sit for a while then try again with the tool. If the holes are stripped you could try drilling 3 new holes for the pins of the tool or even possibly hitting it counterclockwise with punch and hammer. Either way you will most likely destroy the old caps and seals. So prepare for that...
@makingmagicfishing5412 жыл бұрын
Check out my glastron 89 futura. Good video. I think I gotta do this to mine!
@ProjectComplete2 жыл бұрын
Thanks for the feedback!
@craigmoon7206 Жыл бұрын
Where can I buy the manual pump that you used for the Reservoir refill
@ProjectComplete Жыл бұрын
Link in the description for you.
@rodneyhatcher18582 жыл бұрын
My motor goes down slow and up really slow and will need help from me to get it up completely do know why do I have a bad trim motor
@ProjectComplete2 жыл бұрын
Could be several things. I’d start with the cheaper options first. Flush and check fluid, replace seals and check pistons. Then replace motor…
@KevinThomasAdventures2 жыл бұрын
Just refilled same tilt trim system but now when lifted all the way up the lift moter stay engaged. Have to disconnect battery to stop tilt motor from operating. What would cause this? Thanks!
@ProjectComplete2 жыл бұрын
Is it a press and hold trim button?
@KevinThomasAdventures2 жыл бұрын
@@ProjectComplete it is a thumb lever on the shifter. There is also a switch at the bow. I could attempt with bow switch to isolate shifter switch as issue.
@ProjectComplete2 жыл бұрын
Hmm, seems to be an electrical issue rather than a pump or hydraulic issue. I’d start with checking relays and fuses, then move on to the switch to make sure a connection isn’t sticking after the button is released. You could try jumping the switch to see if it stops when the jump wire is disconnected. If it does then you know it’s the switch. I also know some units have a max stop switch that shuts the pump off when it reaches maximum up or down tilt. Possibly that lever is broken or the wiring is corroded. Sorry I can’t be more help. I am by no means an electrical wizard, either way I’d start with the easiest and move to the harder eliminating one thing at a time.
@vonepurser67482 жыл бұрын
Where did you get that tool to take the caps off
@ProjectComplete2 жыл бұрын
Amazon. The link to the exact one I use is in the description for you.
@aquatic_ocean_adventures23633 жыл бұрын
So if your got power but your motor won’t go down is that cause it’s got no fluid left in it ?
@ProjectComplete3 жыл бұрын
Not necessarily. I would start with checking fluid and making sure the pistons aren't seized. Your motor might be shot.
@aquatic_ocean_adventures23633 жыл бұрын
Yep checked that and not a drop of fluid coming out I was using the boat the other week so that’s what I was thinking needs fluid ?
@scottackeret69163 жыл бұрын
where did you buy your tool and O ring kit ?
@ProjectComplete3 жыл бұрын
Link to the exact one I used is in the description.
@NEWME4UNMEBOTH992 жыл бұрын
Why does a motor seem "jumpy" as it is trimmed up & down?
@ProjectComplete2 жыл бұрын
Are you referring to mine or yours? If we were talking about mine. It could be a couple of different things. The portion of the engine moving up and down was edited in fast forward. Which can make things look a like jumpy. Also the trim hydraulics move faster than the tilt hydraulics. So you’ll see it’s slow to move and then much faster once the tilt hydraulic kicks in. The trim hydraulics move slowly for fine tune while boating and the tilt hydraulic moves fast to raise the motor. Kind of like a second gear on a car. But really in person it wasn’t jumpy.
@killahbee542 жыл бұрын
Will this wrench fit on a 90hp tilt and trim?
@ProjectComplete2 жыл бұрын
I am not sure. It does come with 2 different pin sizes, but I’m not sure about the pin distances. It does fit on several different types models. So I would not be surprised if it does work for your model.
@alnowacki7422 Жыл бұрын
Ji I
@Thecoachco2 жыл бұрын
Why does everyone do demonstrations on outboards from the dark ages