Power Wizard Cooldown Duration

How to change cool down time in power wizard panel.

[@amjadfayyaz5510]

Very good Asad SB good informative videos always❤

[@mianjaved6064]

asad bhi boht khub good work thanks

[@alwaystruereality3753]

Thanks Sir!

[@kewalsingh9934]

Good information sir ji 🌹🌹🌹

[@muhammadshoaibkhan4750]

Thanks

[@kewalsingh9934]

Thanks🌹🌹🌹🌹🌹 a lot

[@kashifsaeed7917]

Assalamu alaikum sir is ki ampear ki setting chahie

[@ibrahim_surucu]

I have a CAT generator with Power Wizard Controller and it starts to run after 3 minutes from mains fault. Do you know how to reduce auto start time for 15 seconds ? Thanks

[@AsadElectrical]

Hi, This time can adjust from ATS/AMF controller timer.

[@الیکٹریکلورک]

pls send me ur contct

[@pardhudarling3619]

@@AsadElectrical we can do through the controller

[@AsadElectrical]

you need to adjust start aid time from power wizard. Please check my playlist about power wizard programming videos

[@Hussain-id4wr]

Assalam o alaikum I have some problem emcp 3.1 module please share your contact...

[@MSDMSD-oj9ob]

Sir how to Change frequency 60HZ to 50HZ manual at Power Wizard 1.0

[@AsadElectrical]

You can adjust only during running condition from Volt/ hz adjustment

[@sgmaazamazama6211]

Sir panel pe green light kaam nahi ka rahi kya panel problem hy

[@AsadElectrical]

Light fuse hogyi hogi

[@franciscobalane1621]

Mi nombre es Francisco Andre de Mozambique. tengo un generador FGW com el Controlador Power Wizard 1.0 ...... Quando pressiono el boton de stop el generador se para imediatamente. yo quiero se pare con el cool down modo. Te pido para que me explique como hacerlo.

[@AsadElectrical]

Hi, you have to increase cool-down duration. Please watch complete video so can do it easily

[@AsadElectrical]

Olá, você precisa aumentar a duração do esfriamento. Assista ao vídeo completo para fazer isso facilmente

[@banamalimahata1861]

Sir engine saf caring , not rinig how to problem

[@AsadElectrical]

kzbin.info/www/bejne/m2KUe3-cja6pb7M

[@Azhari-z7x]

AtS koi video banya di

[@Azhari-z7x]

Dse 334 AtS video banya bahut important ha

[@mkhalil6364]

Salam Asad Brthr, I have some powerwizard and generators parchased they are different KVA and models but dont know which powerwizard is for which machine as they are all removed from the related boxes. So how can we configure them for each machine ? is thier computer programe required? Or can be set by its own panel? Regards thanks for your help in advance

[@AsadElectrical]

Wsalam. You can program limited parameters from panel but for complete programming you need to connect software or need to contact dealer company (Allied or SM jafer)

[@mkhalil6364]

@@AsadElectrical thanks a lot for the reply. to be mentioned that all of them are used means they are programed once. My means that can we use a wizared which before was for 65kva now for 33kva with some modification? If yes, could be set it from panel? Or before was for CAT now for Perkins?

[@AsadElectrical]

@@mkhalil6364 It can be use with some modifications via software

[@AsadElectrical]

@@mkhalil6364 It can be use with some modifications via software

[@AsadElectrical]

@@mkhalil6364 you can use power wizard in perkins

[@pardhudarling3619]

Will it stop in automode also same time

[@AsadElectrical]

yes sure

[@pardhudarling3619]

@@AsadElectrical boss how can I check the coolant temperature sensor in power wizard 2.0

[@pardhudarling3619]

In that from connector side B and I is there between that 1.1 ohms resistance is coming and other bank sensor also same value is coming

[@pardhudarling3619]

Fgwilson 1650kva generator I'm facing the problem coolant temperature sensor short high and temperature is not showing

[@Hussain-id4wr]

Assalam o alaikum sir please share your contact I have some problem epcm3.1 module....

[@SAHIDULISLAM-lz6ik]

Sir, I have a Problem, when i press the start bottom the engine don't started and display show me this sentence. SAW: 3927413-00 v 2.2.3 Prod. What can i do please sir tell me?

[@AsadElectrical]

Try to find alarm mode.

[@Hussain-id4wr]

Assalam o alaikum I have some problem emcp 3.1 module please share your contact...

[@Hussain-id4wr]

Assalam o alaikum I have some problem emcp 3.1 module please share your contact...