PowerWizard Start Motor Fault not configured correctly

[@devarrajchinna6510]

Excellent work 👍

[@warishotak1794]

Thank you for the video, it is very helpful

[@nnejiwuiheisrael8510]

We have this power wizard, pls where can it be fixed in Nigeria?

[@joenama9854]

Very helpful to us new beginners, thank you so much and please tell us more

[@domujah2124]

I have a situation whereby the keypad on the power wizard 1.1 panel does not respond while the generator is running. Is there a possible way outnof this problem

[@GD-media211]

After a thunder stick my screen does not saw power what might be the issue

[@tofsupervisor5591]

when I want to stop Perkins GEP88-3 the stop button does not respond, so I forced to stop it by ESD button. Your advice please.

[@FGWilsonGenerators]

Hi! We’re sorry to hear about your issue. You can find very useful information and tips on our operator manual. Have a look at it here: bit.ly/37X74ri. - Emilio

[@andres18gonzalez]

Tengo un evento que me asegura el motor que se identifica como PARD VARS RETROCESO necesito identificar a qué falla se refiere muchas gracias estaré pendiente a la información que me brinden

[@Khaled-fh8up]

Thanks alot I'v one qwestion pls about this controll..

[@gerrylwiza2851]

Kindly assist here I have perkins generator indicating stater incorrect Configured gen not starting at all how to fix

[@ani4real]

Please sir what is the cause of this red flashing LED to come up? because my generator shout down 15 minute after starting and after reset it still come up again?

[@saqibameer77]

I have also same problem

[@mohammadaurangzeb3518]

Got to event log and read the alarm description

[@kingsleyekanem2371]

How do I stop delay start on 1.0 powerwizard panel?

[@a_balanced_perspective]

Which wire number connect to battery charge on Power wizard 2.0?

[@Khaled-fh8up]

Can I factory reset Control Power Wizard 2.1 and how?

[@mdsohelrana190]

Hello sir what can I do if the automatic is going to stop after 30 seconds

[@dipupandit4156]

Your DG hava cuterpilar again again write to display.dg blocked for start.why.pleas reply sir j

[@መቅደላማዕበሉ]

Whow to change oil in cat generator [1275kw]

[@Khaled-fh8up]

I have one generator only make krankining not continue work..?FGW1106C Powerwizard2.1

[@sialuk85]

I am getting error " Gen control not in Auto warning " SPN 4007 FMI 31 . Have tried clearing and it cannot. How do i reaolve this issue ? Help . Control panel is PowerWizard 1.1+

[@mohammadaurangzeb3518]

If generator not in auto it's warning only not shutdown you can start the engine normally

[@mohammadalissa8255]

Hello sir Kindly how I can get the drawing for the genset which is manufactured by fg wilson

[@FGWilsonGenerators]

Hello Mohammad! Take a look at our website www.fgwilson.com. We have some brochures and manuals that could help you (no drawing). If you own a FG Wilson genset and you need further assistance, please contact your local distributor: fydwilson.secgeo.com/

[@abdelazizmakhlas3874]

Hello sir please can you tell me analog input #3 short high wt is men

[@saqibameer77]

Still starter configure is present What I have to do ?

[@FGWilsonGenerators]

Hi Saqib! We’re sorry to hear about your issue. You can find very useful information and tips on our operator manual. Have a look at it here: bit.ly/34P206F - Adrian

[@deivyparra1837]

Que bn...tengo una planta con un fallo..gen control not in auto generator..codigo de falla occ 99 Cat..como puedo restablecer parámetros..gracias

[@mohammadalissa8255]

Dear sir how we can get the flash file for the controller if I want to use the computer

[@FGWilsonGenerators]

Hi Mohammad! Please contact your local dealer for further assistance. You can find a location near you by visiting: bit.ly/2T29HT7 .

[@eyobtadesse1612]

Thanks your video helped me a lot from Ethiopia

[@memoaslan5990]

How to run the auto generator in cem7 screen

[@batalaleswimmingpoolsbatal8826]

Hi. Good morning Sir. Thank you for your informations. I have one problem in my 75KVA genset, when started the RPM shows 955 then genset shutdown and indicate this message: UNDRRSPEED SHUTDOWN. Please help me to solve this problem. Thank you very much.

[@sameershah4378]

Can you please tell me how to connect generator fault alarm

[@FGWilsonGenerators]

Hello Sameer! Please have a look at the operator manual here: www.fgwilson.com/en_GB/support/OperatorManuals.html If you cannot find what you need, please contact your local dealer. You can find the nearest FG Wilson dealer here: fydwilson.secgeo.com/

[@FGWilsonGenerators]

Your Cat dealer can help Sameer! To find a dealer near you visit bit.ly/30vnYJY - Pablo

[@ChetanJadav1990]

Hi boss I'm getting genset control not in present error How to reset this thing

[@FGWilsonGenerators]

Your Cat dealer can help Chetan! To find a dealer near you visit bit.ly/30uFnTh - Pablo

[@aymenaziz4424]

thank alot bro

[@soglophilippetoudji9256]

Comment peut on vous contacter je un génie électrique je peux payer un groupe électrogène de 130 KVA

[@richatgo9177]

How to enable remote star

[@FGWilsonGenerators]

Hi Richat! Please have a look at our operator manual here: www.fgwilson.com/en_GB/support/OperatorManuals.html

[@FGWilsonGenerators]

Your Cat dealer can help! To find a dealer near you visit bit.ly/30vFwWc - Pablo

[@josephkabore6325]

Bonjour,comment allez vs?j'aimerais vous suivre sur youtube,mais j comprend pas l'englais.si vous pouvez faire vos videos et ecrire en bas de l'ecran en francais pour nous autre.merci et bonne suite

[@ezzeddineslimene3104]

Hi,i need the password leve 2 to entre to relai output , please give me a methode to delete password 1 and 2

[@saqibameer77]

I do the same but still red Alarm is coming

[@evermejia7453]

Lo arreglaste??

[@maxisecuritycc0119]

Njce one

[@alkarim4152]

Connection diagrams

[@DavidTorres-go4wu]

Mi caja es Wilson 1163 F119

[@umerqta]

Hi

[@pradeepsahu2562]

Hindi video

[@miwan2447]

Pakai bahasa indonesia

[@tofsupervisor5591]

when I want to stop Perkins GEP88-3 the stop button does not respond, so I forced to stop it by ESD button. Your advice please.

[@mohammadaurangzeb3518]

Either need to replace the powerwizard with new or keep continues E STOP