I built 440 cu. in. small blocks in 1972 for my late model modified circle track car. Bob Gillean at Dearborn Crank shaft did the 4 1/8 billet crankshaft. Dave Crower ground the small base circle camshaft. I designed and machined the custom 4340 connecting rods and fabricated the 180 degree headers. 4 1/8 by 4 1/8. Many comments on Western Pa. Circle track websites. Clate Husted was my driver.
@johnbutera5805 Жыл бұрын
SPINTRON... ANOTHER innovation from the genius of Smokey Yunick, who called it the Smoketron!! 😊 He was the first to use an electric motor to spin an engine and use high speed photography to observe what was actually happening in an engine while running!! AMAZING!! 😊
@InvaderSS670 Жыл бұрын
Running a crossplane V8 to 8000rpm is a thing most people never experience. Unless you go to tractor/truck pulls lol.
@WildShotZ14 Жыл бұрын
Track days too
@davidgalea6113 Жыл бұрын
With the budget these guys have they should be getting at least 9000rpm.. 8000 is easy.
@InvaderSS670 Жыл бұрын
@@davidgalea6113 10,000RPM! Aim higher.
@Bdogg12784 Жыл бұрын
Go to a dirt track. 8000 is low.
@davidgalea6113 Жыл бұрын
@@InvaderSS670 Even higher than 10k is possible (project spinal tap) just not practical which is why I went with 9k.For some reason high rpm is never done on these shows, its where the real technical knowledge is vs bolting stuff on, high boost, high compression, high displacent has been done plenty of times and easy in comparison to reliable high rmp.
@justinreel-t8g Жыл бұрын
700hp all natty?! hell yes!!!!turbos, blowers, and superchargers are cool and all but nothing beats the sound of a naturally aspirated big cam V8 with a lopey idle and breathing fire at 8000 RPM!!!
@taylorsrus9543 Жыл бұрын
How about the sounds of the laughing when a bolt on car with a blower goes past this high dollar build?
@marcalampi5036 Жыл бұрын
At this power level it has good torque response and can spin up and it's a flexible more durable engine. Dependable for racing
@maximusvonce13819 ай бұрын
Easy to make 700hp in a race engine all motor. Almost impossible in a street engine you want to live a long time.
@t0mn8r35 Жыл бұрын
So far this has been my favourite engine build.
@tomp538 Жыл бұрын
The Com Cam was a thing of beauty!
@robertdepyssler2769 Жыл бұрын
Love watching you guys build everything from a basic 6 banger to the high power stuff. I wish I could have you guys build me a striker for my 2004 Jeep TJ. Six Banger by you guys would make my experience so much better.
@Ward413 Жыл бұрын
Watching this show as a kid back in the early 2000’s, all I cared about was V8’s and muscle cars. Watching as an adult now, it’s all their In-line 6 projects that I can’t get enough of. The slant 6, the strokers, the Ford 300. So damn cool.
@sethh8892 Жыл бұрын
Holy shit, thats the comp cams in Memphis! I know the guys that work there, seeing them on camera is so cool! Shout out!
@huntercollins5799 Жыл бұрын
Me too😂 My tool and die teacher in Jackson was a CNC programmer at Comp before his new career and got us a tour out there and introduced us to a lot of guys. I’ve seen Mr.Reed several, several times at Jackson Dragway.
@sethh8892 Жыл бұрын
@@huntercollins5799 Yup, the black dude comes up to our shop all the time to talk to our manager and service advisor at the end of the day. Super chill guy.
@Formerlywarmer Жыл бұрын
I’ve used TCI transmissions since the eighties. I’ve hit three 727 And one 904 in trucks/ cars now and cannot say enough good about their top shelf products and after purchase support! Best ppl to deal with. MOPAR2YA 😎
@craigstark2712 Жыл бұрын
I believe this is my new favorite episode from Engine Power! I grew up a huge fan of small block Chevy's with a 1973 Blazer with the 350, before owning a pair of Camaro's with the LS3. So this was like the best of both worlds for me lol.
@Naoj2024 Жыл бұрын
Nice build.. ! i did a 440 SBC with 11:1 c/r 18 degree NASACR heads with 2- piece Bow tie intake , 1 7/8 ‘’ stepped headers . Camshaft has around .700 lift and solid roller … dyno showed 675 hp @ 600 lbs .. all under 6800 RPM .. We went with a light weight aluminum sprint car block .. i should have went with the SP-2 heads but chose not to at the time…Everyone i talk too says the DYNO numbers are very reliable and not overstated 42:49 ..🇺🇸🏁😎
@davidgalea6113 Жыл бұрын
What nascar heads did you use? Sb2.2? Ford guy myself so not familiar.. wouldn't it be great if nascar still used normal heads/blocks/parts (the kind you can bolt on to a traditional small blocks).. nascar parts were a treasure trove of used parts but ever since 2009 nothing interchanges/ can be used with oldschool parts..the heads need a special block, no more carbs, no ford 9 inch, no 4 speed etc etc..
@heshtesh Жыл бұрын
Your build doesn't sound much different from my 10.7 to 1 399ci 1st gen 89 octane street stroker. 3.625 crank, 4.155"+ bore, 260/266@.050.......679/668...110 lsa solid roller, GM Performance 2 piece intake, Brodix 261cc. 18* C-Series milled to 17*, QFT 950 Black Diamond.......641hp@6400 and 560ft lbs.@5700.
@Naoj2024 Жыл бұрын
@@heshtesh Cool ..! I made a turtle and bolted it in the manifold plenum and picked up 5 hp…easy to do on the 2 piece intake.. good luck..!
@Naoj2024 Жыл бұрын
@@davidgalea6113 yeah the SB2.2 are better than the 18 degree i used.. i kind of agree it would be better if NASCAR used the everyday traditional race stuff … But Toyota ruined all that stuff because all their race engine stuff is just that T.R.D….! You cannot buy any X Toyota race engines and build your own engines..! The engines are sealed units..During the MID 80’s Ford cylinder heads did have a advantage that really showed up on the Big super ovals and it took a little time for dodge and Chevrolet to catch up ..Yes the 9’’ type rear end was standard in Nascar cup , but did you know a GM 12bolt type dropout uses les horse power to run than a 9’’ but rules don’t allow it..! Of course the 9’’ is gone and they now have a weak independent unit…
@Bobthebuilder.69 Жыл бұрын
Man I love these big small blocks. I used to always run 350s, 383s and I still own a couple but I really like my new 434. In my C10, with a power glide with 3.42 gears...it's an absolute handful. It runs n/a like my old 383 on a 125-150 shot. And to top it off, it's now a hydraulic roller cam and I love not having to lash valves all the time. I talked to Nolan at Isky Cams and told him what I was building, he spent a good while talking to me and he recommended the perfect cam for my combo. Just enough low end torque to be streetable and tons of midrange and top end power. I plan to wire and plumb my new nitrous express kit this winter, the engine is built for spray
@robertwest3093 Жыл бұрын
I'm glad that the SBC can finally take advantage of LS cylinder head flow. There's only so much you can do with a 23 degree valve angle.
@ABetterLifeInc Жыл бұрын
These blocks have been out for a long time. Like 10-15 years I think but they are pricey!
@rickybailey7123 Жыл бұрын
Dam 765 lift 783 lift wow that will rev to the moon son of a gun ive never ran a cam that big nice !!
@MrLandslide84 Жыл бұрын
Incredible. Gonna file this build away in my list lol.
@wmbepeo Жыл бұрын
My god, that belt is all over the place!
@scottbourret1190 Жыл бұрын
Something I'd enjoy seeing is someone recreate what could have been the olds w 43. Have been wondering if a rocket racing or mondello block with valley hemi heads may work to pull that set up off.
@Bdogg12784 Жыл бұрын
It's nice to see them take all this time making a cam but they have to get it together with the lifters. I've personaly had 3 lifter failures in 5 years.
@shadowopsairman1583 Жыл бұрын
Springs as well...
@maximusvonce13819 ай бұрын
What lifters brand failed on you. Isky max bushed are the best
@maximusvonce13819 ай бұрын
Run the isky max bushed lifters and you shouldn't have anymore failures
@eieghn Жыл бұрын
You guys ever thought about doing friction reduction on your engines? I have the test schedule to do so. I used to be a Engine Test Engineer with one of the Big 3. Friction reduction could add 3-ish% to ANY engine's output simply by following the Test Schedule - FOR FREE! That would be nearly 22HP on this engine!
@AllenWilliams25 Жыл бұрын
thats crazy i would have not thought of this combo i would love to see more hybrid 350 small block combo for i deas on a 1994 or older tahoe to Suburban applications
@marcalampi5036 Жыл бұрын
Great engine for the Tahoe
@KE0ZCO5 ай бұрын
You guys make a great team. Keep it up.
@autonomous_collective Жыл бұрын
Question: Why aren't cams heat treat again after completion?
@Jake1973_ Жыл бұрын
The final machining doesn't heat the material enough to change the material hardness.
@taylorsrus9543 Жыл бұрын
Heat treating causes distortion, so you have to final machine afterwards.
@rickyfulks889 Жыл бұрын
Why would anyone prefer a gen 1 bottom end over the LS 6 bolt main?
@holeshot1721 Жыл бұрын
Im still scratching my head! The guys asked for something relieable that can take a beaten nd they go and build something with no track records
@taylorsrus9543 Жыл бұрын
@@holeshot1721 I think most of the builds are based on who want to pay for product placement or at least donates parts. These blocks seem pointless and who would use those rings and pistons in a build like this?
@jacobkite5497 Жыл бұрын
The blocks designed for people to be able to swap in all thie gen1 sbc stuff including mechanical fuel pump and timing set but be able to take advantage of 15° Symmetrical port ls heads
@taylorsrus9543 Жыл бұрын
@@jacobkite5497 yup great idea buy a $3500 block instead of a $50 fuel pump and a $100 set of mounts. Only if you are class rule limited.
@DroneStrike1776Ай бұрын
Class spec, duh. It's a road course race car, probably built for vintage unlimited class which probably requires blocks that was used in that generation of cars. Use your head.
@McCracken_9 Жыл бұрын
One day I want to see a big block mercruiser built
@lanegeisewite1436 Жыл бұрын
An LS Small Block Chevy bottom end is stronger than a conventional SBC. Badass build though🇺🇲🇺🇲🇺🇲💪💪💪
@marcotrujillo4279 Жыл бұрын
Man I loveeee engine power good stuff
@WildEngineering Жыл бұрын
best episode yet
@robertwest3093 Жыл бұрын
Comp owns just about every speed parts business there is. Anyone else notice that prices have basically doubled in the last 10 years? They don't need to charge those prices for their products. Selling them at half the price they are now would allow a LOT more people to afford the hobby.
@flamintasty Жыл бұрын
Goddam welfare mentality. Comp are a business, not a charity. 🙄
@donaldgminski8621 Жыл бұрын
The price on EVERYTHING had more than doubled o er the last 10years. The dollar lost it's value. Wake up.
@stevewelborn8744 Жыл бұрын
You two do a awesome job
@AndrewWisniewski-o6f4 ай бұрын
Great show
@aumetalmental8403 Жыл бұрын
What is the cylinder wall thickness at a 4.185 bore on that particular block? 🤔
@p.d.3192 Жыл бұрын
On a 4.4" bore spacing, that leaves 0.215" wall thickness (between cylinders. No idea on the thrust sides).
@aumetalmental8403 Жыл бұрын
Thanks much. I thought maybe you'd think that was a stupid question. ✌️😎
@bobqzzi Жыл бұрын
Cool build, but I have 0 idea why anyone would want an old SBC block instead of one of the many nice LS ones.
@p.d.3192 Жыл бұрын
Better bay-to-bay breathing on the OG small block vs LS blocks. Splayed 4 bolt mains are plenty strong enough to handle what these guys are building it for. Plus, since the block is OG small block, there's less fab to be done to bolt it in most things that originally ran small blocks.
@Timmayytoo Жыл бұрын
@@p.d.3192 I had the same reaction as @bobqzzi and your suggestions did occur to me, but at this point there are tons of LS parts and it seems like they had to have several custom parts made to work with this hybrid block. The only thing I can think of is the oil pump on the LS is quite different than the older SBC so maybe that is the reason.
@jasonbirch1182 Жыл бұрын
Oiling issues.
@p.d.3192 Жыл бұрын
@@Timmayytoohe explains why from 1:45 - 2:10
@taylorsrus9543 Жыл бұрын
Should have used a Dart.
@carguybikeguy Жыл бұрын
I’d love to see a build using this same road racer engine ethos to a Vortec 4200 or a 261. The 261, like that 300 y’all built, would benefit from modern witchcraft. But that 4200 could sing & maybe even hunt down some of these V8 builds.
@CJColvin Жыл бұрын
They need to make a home made 6.8L DOHC 40V Triton V10 by using 4 sets of 4.6L 4V Cobra heads by cutting-em and welding-em as well as porting and polishing the modified Cobra heads, use some custom made camshafts from either Comp cams or Lunati, and a custom home made intake manifold and man you have you're self a Homemade 6.8L DOHC 40V Triton V10 making over 700 HP NA with some custom Homemade parts as well as some beefed up factory parts.
@jamesgeorge4874 Жыл бұрын
Could just boost a 3V.....
@CJColvin Жыл бұрын
@jamesgeorge4874 Yeah but it won't be as reliable as a Homemade NA 4V V10.
@jamesgeorge4874 Жыл бұрын
@@CJColvin because "homemade 4V 10's" have a stellar track record ? I know of 1......
@donaldgminski8621 Жыл бұрын
The V10's in general have a great track record. About to hit 600k, myself.
@CJColvin Жыл бұрын
@@donaldgminski8621 Awesome brother
@DBSSTEELER Жыл бұрын
440 CI, LS7 top end and you made 31 more HP than the basic 416 LS3 stroker Richard Holdner used in his Rec Port LS intake test using the stock LS3 intake manifold. I would have expected this combination to push over 700HP.
@redcatxb125Ай бұрын
it made 721 at 40:50
@zachniverson8816 Жыл бұрын
Just curious Frankie, did u weigh the rings, wrist pin, and locks with the piston and rods when you balanced it. The video just shows the piston and rods being weighed so I was curious
@leonardhirtle3645 Жыл бұрын
An amazing engine going into a beautiful car.
@metalted6128 Жыл бұрын
Why for street racing, not an aluminum block??? Less weight equals faster lap times.
@DroneStrike1776Ай бұрын
Jesus dude, it's class spec. Do you not know anything about road racing? They probably run in a class that doesn't allow a modern block in a vintage car.
@rogerbennett2025 Жыл бұрын
getting anything from Edelbrock/comp cams for a AMC 390 took 10+months
@donaldgminski8621 Жыл бұрын
Sorry. I robbed all the good parts from the junkyard.
@lesliesmith2586 Жыл бұрын
Good job on the safety. You don’t need eye protection.
@KE0ZCO5 ай бұрын
Which do I like more? Very high end tools and machinery? Or, custom built high-end engines?🤔😊
@franknukemcomegetsome2744 Жыл бұрын
Absolute perfection!!!!!👍😸
@vortecturbo Жыл бұрын
Man that's absolutely awesome that combination would have made even more power and more torque with a big CID CNC 4500 series single plane with a big 4500 series throttle body that 102 is too small for that combination
@marcalampi5036 Жыл бұрын
I think this manifold makes better torque
@billbonu1639 Жыл бұрын
Make the same motor a two stroke and I'll be impressed.
@KS-dg5zh Жыл бұрын
I would have added more timing.a typical 15°headed small block will take as much as 34°.I think they could have tapped the 800hp mark
@patmcbride9853 Жыл бұрын
Kudos to Edelbrock for moving their HQ out of Kalifornistan.
@taylorsrus9543 Жыл бұрын
Of course they moved to a place to exploit tax laws and can pay workers $7. Keep in mind tho, their engineering is still in CA because MS doesnt have that talent pool.
@raystevens687 Жыл бұрын
Nice job on the engine
@AcidTeegx Жыл бұрын
I would like to here more engines being built to at least 8k rpm again 😂😂
@willybird3377 Жыл бұрын
there's a "ton" of tons in this
@BigDipper798 ай бұрын
It’s great to see these parts being made in the good old USA. Buy American. No more chinese junk.
@JSFGuy Жыл бұрын
All right, let's check it out.
@bluecollarfox913 Жыл бұрын
That was wild to see.
@jakegorman71219 ай бұрын
Would have been nice if more detail went into explaining exactly why you went with a conventional bottom end and what the advantage were over the ls platform
@carm44035 Жыл бұрын
I have a few questions. Why use head bolts instead of studs? Did they use roller cam bearings? Will a Jesel belt drive fit under a timing cover?
@Twogreenfeet7 ай бұрын
Yes, wet timing belts exist.
@frankcastle9691 Жыл бұрын
I wonder if they use ARP bolts.
@Twogreenfeet6 ай бұрын
I'd like to see a dyno comparison VS an LS bottom end. I wonder what the windage differences are. If better windage is desired I"d probably go with a PROPERLY knife edged crank than drilling holes to balance. My guess is windage differences are probably minimal with a dry sump.
@ManiacRacing Жыл бұрын
Nobody ever mentions how close a SpinTron test rig sounds to a running engine, despite not actually burning any fuel! At high rpm, they sound like running engines
@billbonu1639 Жыл бұрын
I would have used arp studs for the heads and mains if possible.
@macthemec Жыл бұрын
Hey i wanna hear about these race tug boats!
@racer193wr Жыл бұрын
These have been around for a little while now for anyone thinking this is new, its not. Hot rod or car craft did a feature years back now on how to gwt ahold of the parts and how to build this engine. This would be my dream build if i could ever afford to do any of this stuff..
@toolman90815 ай бұрын
This wouldve been a good opportunity to build a SB2
@TheCosmicGuy0111 Жыл бұрын
Nice
@hotroder105 Жыл бұрын
So at the end of the day you spent a crazy budget to make what a good ls7 can make...
@shadowopsairman1583 Жыл бұрын
Or a 454LSX, there is the Nascar SB2 or R07 as well.
@19chev81 Жыл бұрын
But this will last longer in circle track racing running constant high rpm
@slowpoke96Z28 Жыл бұрын
@@19chev81literally what the LS7 was designed for. It was made to live close to its redline. The fact it doesn't have to spin to 8,000 rpm to make its power is just a bonus. The only thing that would make this make sense is if bore or stroke is limited to a certain thing or a certain type of block is required.
@ForneyRider Жыл бұрын
This one is heavy duty for drag racing. It makes the power and has longevity.😊
@hotroder105 Жыл бұрын
@@ForneyRider it's built for a road course car. You can easily build a reliable 700hp ls for less money. I like that it's different but the end product doesn't justify the level of parts and budget
@there_is_nothing_here Жыл бұрын
Okay hold up. I'm not an engine builder so I'm kind of confused. Is it a custom block? How would LS heads fit on an old SBC? Or do you mean an LQ9 vortec block?
@jesselee128able Жыл бұрын
Its a motown block. Its specifically custom made for the LS top end. Google world products motown 2 LS. The problem is, the blocks 3500$ lol
@marcalampi5036 Жыл бұрын
I see I thought it was the old small block I didn't realize it was a specialty block
@scotthultin7769 Жыл бұрын
Big block Chevy is the way to go 🤯
@19chev81 Жыл бұрын
Not for constant high rpm on a circle track....
@taylorsrus9543 Жыл бұрын
@@19chev81 They do it in boats all the time, way more than this probably does.
@mikalegault9012 Жыл бұрын
Eventually, I would like to see them build a flatplane V8 like the mustang 350R
@ardennielsen3761 Жыл бұрын
circle track car only needs 350hp to 400hp to idle at the average track speed. but i can bet that engine needs a radiator the size of two K20 engines.
@NewYorkPizza444 Жыл бұрын
TCI ...... 👍 !
@chrisferguson1911 Жыл бұрын
That Camaro looked great. Was there something unseen that was the reason to buy that for race instead of some junker with no title?
@19chev81 Жыл бұрын
That camara had alot of issues. There was front end damage, fenders were buckled. It wasn't as nice as it looked on camera
@chrisferguson1911 Жыл бұрын
@@19chev81 Thank you.👍
@reltub200019 ай бұрын
FR3. YOU USED FR3 in a torque 454 several years ago. I have always wondered about additives. Unfortunatly, the FR3 was added before the first dyno test. This did not allow anyone to find out if the additive worked. Could you please get a few dyno runs on an engine to establish a base, the add the FR3 and test again. This will either prove or disprove if the FR3 works as advertised. Thank you
@supertruckertom Жыл бұрын
There were plenty of old beat up Camaros to hack up into a race car.
@jakegorman71219 ай бұрын
Having the 6-bolt mains in the ls I'm surprised that the conventional is the way you went
@SloppyMechanics Жыл бұрын
that thing has some legs up top
@The_Performance_Laboratory Жыл бұрын
Why such a large ring gap for an NA engine?
@rotaryray4 ай бұрын
That engine is restricted by the intake manifold and still makes respectable power. If they put a CID 5.0 LS7 intake manifold on that engine it would probably make 740-765 HP
@mistabone3899 Жыл бұрын
@14:42 precision torque wrench, looks just like mine except left handed. Click click.
@Ultegra10SPD11 ай бұрын
I-Beams on an extreme road race engine? -U10
@Sir.VicsMasher Жыл бұрын
🎉 Yay high compression! With the abundance and popularity of e85 especially in late model boosted applications, I think most of your engine builds should finish by swapping in a solid roller camshaft and high compression pistons. High dollar, high performance TV show engine builds on pump gas = 😴
@scotthultin7769 Жыл бұрын
146 👍's up thank you for sharing 😅
@LSmaniac253 Жыл бұрын
Love these guys
@michaelmaher4328 Жыл бұрын
can i run this engine with a carb gulping e85 ?
@bmstylee Жыл бұрын
Yes but why use an obsolete technology
@kkoch666 Жыл бұрын
Carburetors are far from obsolete there tin lips..
@bmstylee Жыл бұрын
@@kkoch666 keep telling yourself that and it still won't make it true. You also probably think single circuit manual drum brakes and 6 volt electronics are just as good as what we use now. Technology advances and carbs, like CRT TVs and flip phones are well and truly obsolete even if a small segment of the populous uses them because new technology scares them.
@taylorsrus9543 Жыл бұрын
@@bmstylee To be fair, a carb will make more power, every time.
@Twogreenfeet7 ай бұрын
@@taylorsrus9543 Direct injection makes more power than carb or efi of any kind.
@Franciscolozano38 Жыл бұрын
You rebuild engines for custumers?
@michiganporter Жыл бұрын
Pats pocket on his shirt is bout to burst lol!
@pascalhumphrey Жыл бұрын
I would like see them try building like a F1 engine. 2.5L, 13000 RPM
@bmstylee Жыл бұрын
Yeah that would be out of their area of expertise. F1 engines are insane to put it lightly.
@pascalhumphrey Жыл бұрын
I think they have the smarts to do it, especially Pat. @@bmstylee
@bmstylee Жыл бұрын
@@pascalhumphrey tell me you know nothing about what is involved in an F1 engine build without saying you know nothing about it. Building a pushrod V8 that revs to 8k max is not even remotely close to a modern F1 engine that idles at 4k. The old 3.0L V10s idle higher than most of the dyno pulls they make and run to 20,000 RPM. So yes he might be able to build one but don't expect it to last very long. Pat's a very good engine builder but not in that area.
@marcalampi5036 Жыл бұрын
F1 engines have very tight tolerances and have to be heated with oil before even starting the engine. Not practical at all
@bmstylee Жыл бұрын
@@marcalampi5036 tight tolerance is an understatement. Until they get it warmed it's basically seized.
@stephenmoulton9284 Жыл бұрын
what is up with the old mopar v6's , the ones in the LH and forward in time, the good the bad and the ones that can be hopped up > reliably? > The last big 6 used in minivans and jeeps ? As things like cost / mile count any way to hop them up and keep them affordable to run ? WE have all heard the story's , 8 mpg at 30 or 130 . yea not at $4.00/gallon
@NewYorkPizza444 Жыл бұрын
I need you guys to show me , How to use those torque wrenches correctly Gg 😅 ....
@shinymud7 Жыл бұрын
Frankie looks great he grew a beard, now he don’t look so baby face weird.
@maximusvonce13819 ай бұрын
I hope he's running Isky Max bushed lifters and Isky Gold stripe dual valvesprings...lol
@richardturk7162 Жыл бұрын
Amazed how there is a lack of manifold gaskets.
@xavierhamilton155010 ай бұрын
All this in Mississippi… olive branch Is like 30 to 40 minutes from me
@murphyr31 Жыл бұрын
I’ve never done an engine build before. Can anyone tell me how much they think this particular engine build would cost? I’m assuming that if you were building a 700 hp engine that was going to see more day to day driving you’d probably use a bit of a different parts list so I’m not asking for exact numbers.
@maximusvonce13819 ай бұрын
$25k race engine only
@clintonsmith9931 Жыл бұрын
And exactly which part was made in the GM factory? Why do people say it is a Chevy or such when it only looks like a small block Chevy. Guess the local wrecking yards ran out of sbc 350s to put big money in.
@randyj9965 Жыл бұрын
My stock aluminium block 415 with gm performance parts cnc heads and a cid 4500 intake makes more than that.
@19chev81 Жыл бұрын
But it wouldnt last as long on a circle track at a constant high rpm
@randyj9965 Жыл бұрын
@@19chev81 maybe not, but that would be block related. I have just as good bottom end stuff as they do, callies crank and rods, but not near as good of heads as they do. That's why I make power at 7k not 7700, and I make more torque from less cubic inches.
@n.b.p.davenport706611 ай бұрын
Build a drag and drive car !!!!
@samueljackson247811 ай бұрын
Do a Ford Parklane 410 Marauder
@jamesalexander7540 Жыл бұрын
Pat is starting to influence Frankie.
@leonwayne7657 Жыл бұрын
He will need a Pat propriotry pocket pen support harness under that shirt soon as well. 😂
@AndyPat239 Жыл бұрын
the summit racing pen protector 5000 !
@leonwayne7657 Жыл бұрын
@AndyPat239 I love watching the builds here on the channel and enjoy seeing some of the younger generations absorbing the information with awe. All they/we need is the finances to keep the dream alive that you guys live and breathe on the channel. 🙌
@keithhastings4092 Жыл бұрын
16:40 when the unasked for commercials end and they actually start to build the friggin engine…
@harveylong5878 Жыл бұрын
PN is nothing but glorified infomericals, product placements. when the corporate overlords err I mean sponsors pony up for a build, they expect their product shoved down audiences throat at every chance
@dancampbell4400 Жыл бұрын
No sponsors, no show. Gotta take the bad with the good man
@bryang9158 Жыл бұрын
Bad ass but it's at least 75 ft lbs down on tq
@slowpoke96Z28 Жыл бұрын
1:58 its hard to take anyone serious that speaks of LS engines as if they are not small block GM motors also.
@grantstricklin5 ай бұрын
400+cfm on heads it shouldve made 800+ easily.. maybe bigger cam not sure but was expecting more.