Thank you for making this video. I live way out in the sticks and getting a spa repair company out here is impossible. You saved me a fortune.
@andreperras Жыл бұрын
You are very knowledgable, helped me save my tub from freezing at 2am in Canadian winter lol
@kathyweigelhi-lophotovideo29842 жыл бұрын
By far, the best tutorials.
@wowchad2 жыл бұрын
All your videos are helpful, but this one is the best yet!
@douglasthompson94827 жыл бұрын
Great video...cleared up my problem. My tub required a higher amp switch. Thanks!
@champflyer4 жыл бұрын
I hate you Spa Guy! Just kidding! You're awesome. I've literally rebuilt two hot tubs because of your guidance.
@Gizmobyte7 жыл бұрын
Thanks for the information on the pressure switch. I didn't know what it was or how to get it off when swapping out the heater. Ended up turning the little plastic adjust quite a bit before I finding out the whole thing screwed off. I'll do a continuity test to adjust it or get a new one if I can't get it to work properly.
@TodColbert7 жыл бұрын
2007 Caldera Niagara - I've replaced the pressure switch at the beginning of the last two seasons due to the temperature going too high. That has fixed my problem each year., now again I have a similar issue, but slightly different. Refilled, flushed, drained, refilled and replaced filter. Spa comes up to temperature and maintains during the daytime, however, by morning, the spa is at 99 degrees and there are four solid lines on the control panel indicating high limit error. Before I replace the switch again, I thought I would ask you if you think I should take a different step. Also, I want to verify that this model should use the 25amp switch not the universal 1 amp (the 1 amp switch does not look like the one that came out originally). Thank you kindly for your advice.
@LeBen556 жыл бұрын
Thanks for your goods troubleshooting tips, I will use them as soon as spring comes around.
@Aldo-zp8wk5 жыл бұрын
Wow love how you explain everything. Good job please keep up the quality videos. Thank you sir.
@BillGeddes Жыл бұрын
This is so step-by-step and helpful... thank you! Have a Hot Spot TX that had the double yellow lines. Figured it was a bad switch so got a new one and installed it and... same. When I turn it on and turn on the circ pump, I can definitely feel/hear circulation through the heater manifold. If I short the circuit the heater does turn on, so it doesn't seem like a board issue. What do you think: bad replacement switch, or...?
@liqin34676 жыл бұрын
Hi Spa Guy. Thanks for the video. I learned a lot. Mine is an older hot tub. It works well until recently when it threw a FL code and the heater won't heat. The pump works and the current seems normal. I tried to jumper the pressure switch to by pass it. But it did not work. What other check would you suggest? Thanks!
@darkknightspirit5 жыл бұрын
Hi Spa Guy, I haven't gotten any error code but the hot tub heats when it feels like it, there is no obstruction in the filter and the pump works regular. I left the hot tub running continuously all of winter and it only got to 100 degrees once and I dont know if the issue is the pressure switch or the heat exchanger. FYI this is a Cal Spas from back like 2000's (2100 series) from what i gather... the hot tub came with the house when bought. Last summer I swapped the dually pump for the replacement pump.
@SJChannel6 жыл бұрын
This is an excellent video -- very well done. It explained everything I needed to know. I replaced my pressure switch and the hot tub is working fine again. Thanks!
@ebrobbins55235 жыл бұрын
Great video!!! I have a balboa 2000 LE system with the two M7 sensors at the side of the heater as you so clearly show. My system starts normally, but the temperature quickly reads 118 degrees (in just a minute of operation) and shuts off. Codes displayed are OHH and FHL with the filters removed. Any thoughts?.
@oconnelljk5 жыл бұрын
hey spa guy. i have a six year old jacuzzi hot tub and recently getting a FL1 code. Did some research and lead me to pressure switch. I changed the switch and still getting the FL1 code. I have changed the filter and checked for any debris - all seem good. Additionally, the FL1 code comes and goes. Sometimes the heat pump 1 works just fine - other times the FL1 comes on. One additional interesting finding - when I use a bypass alligator clip wire to connect the red and black on the switch, everything operates perfectly fine...this is what lead me to believe it was the pressure switch. What do you think Spa Guy? Thanks a lot.
@jazzykazz95297 жыл бұрын
Hi Spa Guy, I'm new to hot tubs and I just got a used one hooked up by an electrician 5 days ago. The pressure switch was broken so that was replaced and the tub heated up fine to 102 degrees as set. After about 24hrs the tub shut off for about 4-6 hrs with a "FL" error code… then came on again for 4-6hrs… then off again. Because the pressure switch was just replaced I adjusted the calibration wheel on the pressure switch, thinking that was the issue (I've since watched your video informing me that is a no no). Then, I took out the old filter and a couple hours later the tub came on again. Since then, I've put in a new filter and the tub has been running for a couple days without shutting down….. but now the temp won't get to 102 -- its at 91 right now. Did my tampering with the calibration on the pressure switch lead to the tub not heating? Can I make pressure switch right again? …perhaps another issue.
@SpaGuy7 жыл бұрын
Hello jazzy kazz, Do you know the history of the tub? Were the electronics replaced recently? When is te last time it worked correctly? Have you ever seen it work correctly? The reason I ask this is it could be a man made issue not a mechanical issue.. Also what brand is the tub and electronics? Spa Guy
@jazzykazz95297 жыл бұрын
Hi Spa Guy. I don't know the history of the tub. I got it from someone who moved into a house and they didn't want the tub anymore. The tub seemed to be working when I originally looked at it and on the day it got disconnected and moved -- by this I mean the jets turned on and the temp was 98. Its a 2001 Beachcomber 350 model and the rating plate on the heater/electronics casing says "Balboa Instruments" model DD-2500ES-DCAJ (there are a couple other stickers on it too). Earlier today I turned off the breaker, waited a minute, then turned it back on. The tub didn't come on but it displayed the "FL" error again. I went out for 3hrs and when I got home (10 mins ago) the tub/pump was on again with no more "FL" error and a 89 degree temp (its subzero temperatures outside here). The tub heated up fine last Saturday when it first got hooked up… that was until the first "FL" error shut it down. It seems like such an easy fix, like a minor tweak or adjustment. Any suggestions before I bite the bullet and hire a service technician? Thanks Again
@jazzykazz95297 жыл бұрын
I've since got it to a point where I can reset the tub from the breaker and the tub/pump turns on right away with no "FL" error code. Still not seeing the heater/red light come on right away. Currently the jets are on high for its 15min cycle to give a little work out.
@ItaComedian6 жыл бұрын
Hello “Spa Guy”! I watch your videos a lot online and really appreciate the level of sharing, very educational and informative. I have a question and it would be amazing if you had the time to read it over and offer guidance. I purchased a used, older hot tub. I don’t know the exact brand but it is old with one pump and minimal jets. It has a Spa Pak Gamma 240 (very analog old school, no display etc) When purchased, I was told it needed a heater element as the breaker was tripping, so I’ve replaced that. I just had the electrical connected yesterday. So, with the heater switch in the off position, I can turn the tub on. The pump comes on in the low setting just fine. I can even press the “button” (the type that activates the second speed with an air line to the spa pak) and the motor kicks into higher gear and the jets seem to work, no problems. As soon as I turn the heater control knob to “on” the breaker trips, this is my issue. Today I went and bought a new thermostat, replaced it and same thing. I also disconnected the high limit switch and tried again, same thing. I have since found one way to make it so that the breaker doesn’t trip when I turn the heat knob on - I pull the water tube that comes from the heater element tube on the pump off of the connection nipple to the pressure switch that is part of the spa pak. When I pull that tube off, water of course freely flows out of it. When I kick the pump into high gear, it comes out with more pressure. And again, with this disconnected, I can turn the heater knob on all the way. Now I have no idea if it’s actually heating anything, but the breaker no longer trips. From what I have read online, (and I think even heard from you) the pressure switch won’t normally trip a breaker unless there is a water leak into the pak, and after pulling it off, I don’t believe there is any leak. In fact, the little unit looks new given this tub may be 25 years old. Not sure if it matters but the switch is called “The Little General” switch number DD05SS Would you have any suggestions or ideas for me? Any help is greatly appreciated. PS - there was a while there where I couldn’t figure out for the life of me why my KZbin “suggestions” were filled with Elvis Presley material, but after spending more time in your channel, I realize you’re the culprit! :) Thanks, Rob
@Chris-sw9es6 жыл бұрын
I have an M7 Balboa system, and not getting heat. Flickering heat light on control top, element and sensors test fine and no codes.. flickering heat light than eventually goes steady solid but still not heating. Any advice? Tested heater and sensors, appear fine, filter is clean, something on board or board itself?
@livewoutwarning75 жыл бұрын
Spa Guy! My hydropool serenity is showing HL but the water is ice cold, had a faulty pressure switch which spitting water all over. I replaced that and the spa runs when the heater is not hooked up but displays HL. When i reconnect the heater it trips the breaker immediately, but did not do that before i replaced the pressure switch! Any advice?
@koihoshi2 жыл бұрын
So I've got a weird one. I restored an old hot tub. I have a united spa T5 topside that has been stuck at 102 forever. No flo codes. Pump works, heater works, everything is great, except the buttons on the topside are screwed up. So I was reading that as long as I have a b5 board or newer, (Which I do, a B5 board), I could replace the topside with a T7S. So I did. I plugged it in, and EVERYTHING works great, EXCEPT, after 5 seconds whether the jets are on high or low I get "FLO" error. What's odd to me is if I hook the old topside back in, no errors at all. The only time I got a "FLO" error on the old topside was when I was burping the hot tub. That's all corrected. I pulled the filter, checked all the plumbing, checked the pump, everything is working exactly as it should. But I'm still getting "FLO" with the new topside. I'm wondering if maybe the pressure sensor is having issues? Maybe the "low" pump isn't moving enough to hit the switch? It's definitely odd.
@cjwolf2510Ай бұрын
My old school switch actually started to leak. could you use a newer type or is there a conversion type of switch?
@payakadventures2 жыл бұрын
O am eliminating my pressure switch and installing a flow switch on a pool heater due to elevation differences. There are a high and low pressure switch. Do you know which one I should connect the flow switch to?
@SeecondToNone15 жыл бұрын
Recently bought a house and it has an indoor hot tub. The plate on the Raypak heater is 1988 "model EL 552-2" It's a very old system but to my surprise after fiddling around with a few things it worked. All I have to do is open the valves and put water in it and the pump and air blower turned on. The heater turned on for a while and then turned off but it was heating. My pump has 2 speeds a (high) and (low.) There was a note from the previous owner that said always run on low unless you're in the hot tub then you would turn on high. When I turn the pump on high the heater always works but the heater no longer works on low. To me this seems like it's a pressure switch. I just found your video in my search for what to do. Should I order the new pressure switch from raypak? Should I take things apart to see if there's something in there maybe the pump? I've never had a hotrub but I feel like the pressure in the tub part seems good. A nice little current on low and nice hard jet on high. With pump on low heater does not sense flow.
@amberloscar93895 ай бұрын
So I have a dynasty hot tub and a Flo code popped up and no temperature. I can not find any of these two on mine. Could you please help me.
@shawnlee9213 Жыл бұрын
I have the last balboa my pump keeps turning off and on no codes what do I need to do
@joshdaniel31652 жыл бұрын
I had to replace the display on a older balboa hot tube started is up made a gummy sound now I can’t get any power to the display or the tub it’s and old board no rest button that I can’t find should I look at the fuse
@dartagnantaft59184 жыл бұрын
What would cause my pump to not turn off and over heat the tub? Which now after about a month my heater is going out. I get my parts from you but not sure what I need. I'm greatfull for any help you can give.
@kevinkelley61422 жыл бұрын
Spa Guy, I need some help. I have a Jacuzzi Hot Tub J330. I am getting a F0 code and a 357 code right when I turn it on. I am beside myself. Any suggestions? Thanks Kevin
@travisyoung94803 жыл бұрын
Question??? Ok so i have a hot tub i just got used and the light isn't coming on and its not heating up, also water is only coming out of 2 or 3 jets could that make it not heat up or make the light come on
@mmarzolo15 жыл бұрын
I have a balboa 3 amp 30408 PS.....can I replace with TecMark 1 amp? I don't see many 3 amps sold anymore. anyway I love the videos. I have learned and saved $$$
@SpaGuy5 жыл бұрын
The Amperage doesn't matter on that system it is not even close to 1amp in the circuit.. Thanks for Watching.. Spa Guy
@adamberrisford79554 жыл бұрын
I have a MSPA hot tub model dsc04 which I got for the start of lockdown and Monday july13th the pump or the bubble blower motor or heater element has broken down coz our rcd breaker for the sockets trips out when we try to turn on the bubbles
@mindstroker17 жыл бұрын
Hi Spa Guy. I am having problems with my baja spa. Flo error message. Drained and refilled. Checked filter and removed filter. Had a spa repairman come and replace the pressure switch. It came back on and he said he didn't have any idea and wouldn't come back. I checked the empeller and it is clean and turns easily. It pumps water through the system. It will run until it reaches temp then the flo error comes back on. If you restart it, it will run until it reaches temp again. It seems that I can keep bleeding the system and I can't figure out where the air is coming from. From everything I have read it points to the circuit board I would be most grateful for any suggestions. Also, when you press the pump button you can hear the heater switch click and the FLO disappears and the temp comes on...
@SpaGuy7 жыл бұрын
Hello If it is running to temp and then giving an error message the pressure switch is stuck closed.. To verify this after it gets to temp and the flo error comes on unplug the pressure switch on one side and the error should go away.. or you could verify that the Pressure Switch is open with a meter when the pump is not running... Spa Guy
@michaeljohnson97142 жыл бұрын
Wow that’s good news
@joeb41173 жыл бұрын
My Jandy LXi ignites but quickly goes out, any ideas? It attempts to reignite a few times but same issue. Pool DE filter clean, plenty flow.
@mellahey5014 жыл бұрын
my costaway inflatable is not heating. No error codes. Doesn't look like any water damage on heater or circuit board (by looking at outside). Does make a harsh rumble noise when pressing the heat button then goes back to normal. Just never heats. less then 6 months old.
@ryanthompson80544 жыл бұрын
I have a calspa and I'm getting psol and psoh code. Jets and nothing are working. I jumped the switch which turned off the code so I know I need a new switch but jets still won't turn on. What else could it be ?
@BensonCrew8 ай бұрын
Does your tub need to be filled with water when you replace the pressure switch or is okay to replace the pressure switch and then fill the tub?
@SpaGuy8 ай бұрын
Unless you have slice valves you can close to keep water from leaking you have to drain the tub before replacing the valve..
@mason220ful4 жыл бұрын
I have M7. Circ pump working. All pumps had connections loosened to get air out. Sensors removed and checked for debris. Still getting HFL to FL codes
@troyalec502 жыл бұрын
I get the FL code and the only way I can reset it is to pull one wire off of the pressure switch. The pump immediately comes on (with good flow), but the heater won't come on until I reconnect the wire. Then, it works fine until it gets up to temperature, but then it shows the FL code and we have to start all over. What do you think is the problem? Thanks.
@SpaGuy2 жыл бұрын
I tell you the answer in this video..
@tobiashall8694 жыл бұрын
The control board light come on with no numbers what is the problem
@erikpeddle Жыл бұрын
Need help with 2022 catalina. !!
@alanlenzi38946 жыл бұрын
My sun dance altmar 2000 has a 2 speed motor. on low speed the motor runs and the shaft turns but very little water comes out of jets. Hi speed is fine and jets work fine what good it be?
@diyoverload16315 ай бұрын
I have an '08 HotSpring Grandee. The wire for the pressure switch goes inside a closed box at the end of the heating system flow pipe elbow where the other sensors are located. I'm afraid to open this with full tub to see what's in there. Will I find a switch replaceable by your 1A switch? Will it fit the compartment? Can I replace it with a full tub?
@SpaGuy5 ай бұрын
If you have ano fault style heater which it sounds like you do just bypass the pressure switch.. The new version of the heater no longer uses a pressure switch.. You just cut the wire and tie the two wires together on the side that plugs into the board.. Thanks, Spa Guy
@diyoverload16315 ай бұрын
Thank you for the quick reply. I was confused before but I have the older style heater with a built in pressure switch and a pressure switch cable the comes from the heater for connection to the control panel. This was working for 15 years but recently I had a flashing red and green light which would not reset indicating a bad internal pressure switch which I confirmed by bypassing. Is there any safe alternative to replacing the heater. Please advise.
@dennissilance54086 жыл бұрын
Spa Guy...FL1 code on my Spa Builders LX-15 hot tub. changed out pressure switch, no luck. Motor just clicks and then turns off almost immediately. A few minutes go by and same sequence occurs. Still reading out between water temp and FL1 code on topside. Filter removed, no obstruction in propeller. Any advice greatly appreciated. dsilance
@dennissilance54086 жыл бұрын
Update: after speaking to spa guy on phone he pointed me towards the motor and sure enough bearings were bad. Local electric repair shop was able to replace. Thanks for your help spa guy.
@jerryhatfield76506 жыл бұрын
I have a Balboa system and I'm about ready to replace the pressure switch. Question about the pressure switch is there any polarity with the wires does the red wire have to be on top or does the black wire have to be on top or vice a versa. Since I'm not the first owner of the spa tub the red wire is on top of the pressure switch the black is below it. Is this correct? Thank you for this very informative video
@SpaGuy6 жыл бұрын
Jerry there is no polarity on a pressure switch.. It is simply a normally open circuit that closes with water pressure and connects the two wires together.. Spa Guy
@jerryhatfield76506 жыл бұрын
Spa Guy thank you sir I just filled up my tub and running a test cycle. So far so good! Thanks for the quick reply
@paulmiller16565 жыл бұрын
Hello I am haven't issue with my new heater and board . Is there away to get help from ya
@remmosimann43736 жыл бұрын
do all hot tubs have a pressure switch? we can't find one on our older tub.
@eugenedavenport6 жыл бұрын
I keep getting HL code but the water is cold. What would I need to do to fix the problem?
@donna48402 жыл бұрын
Can someone help me with replacing the prozone V3 injector on my Master Spa Legend Series LSX 1050 FST
@RecycledAndSaved7 жыл бұрын
So our jets are working, the filters aren't plugged and there is hot water bubbling out of the base vent. Everything was great till last week. Now, no matter what we set the temp at, it ONLY heats up to 86 degrees. It has been at 86 degrees for several days. So its heating and monitoring the temp, just not taking it up high enough. ITs a Tiger River Sumatran. Thanks in advance for any suggestions.
@SpaGuy7 жыл бұрын
It is not heating... Just water movement friction through the pump and heat from the motor will cause it to heat to a certain point based on the ambient temperature.. There is on most of these tubs a No Fault 6000 heater... If yours has that heater there is a hi limit button hidden on the top of the heater black box... it is under a clear plastic cover and can be tripped... I would look there first... while is is possible you were feeling hot water from the heater jet you usually cannot feel a temperature difference from there if the system is working correctly.. I would start with the reset.. You really need a meter with an amperage clamp to see if it is really heating or not.. If it has an IQ2020 or IQ2000 some of those packs do have a heater board that goes bad on the left... Spa Guy
@lizabethtfclittletaylor57546 жыл бұрын
What up with pure spa inflat message e95 what do I do
@MyFighter20004 жыл бұрын
so when pump is running is the pressure switch open or closed? My Cal spa 2100 the contact is open with or without running pump?
@SpaGuy4 жыл бұрын
Closed..
@watchman61045 жыл бұрын
What if it is clicking on and off?
@kattyboombatty1006 жыл бұрын
Hi. We have a Dynasty spa that has an HR error code on it. The book says it needs a new spa pack. The pumps and heat are not working. Any thoughts? THANK YOU!
@SpaGuy6 жыл бұрын
Kathy, What kind of pack is it? If it is an Aeware then most likely it is a bad pack but I would not put one of those back in..
@kellymorash34 жыл бұрын
Great video. I have a Gecko spa pack that now give me 3 dots on keypad and no heat, indicating no flow. I calibrated pressure switch, did not help. I bypassed it altogether and shorted the leads from pcb and powered it up, and got it to heat, but usually after a couple hours of trying to get up to desired temp from 70 degrees, i get the 3 dots again and heating stops. Why would this happen? If the pressure switch circuit is closed, it should never trigger a flow error? Am i missing something? Thanks.
@ronives18953 жыл бұрын
I have the same problem. Did you solve it? If so, what was it ?
@kellymorash33 жыл бұрын
@@ronives1895 No, not yet. I just drained and covered it for now, and moved on to a different project inside. I’ll revisit it in spring.
@dalehansen50405 жыл бұрын
What is the FC code, F 2, F 4, F 6, F 8 mean?
@tylerbarnett16943 жыл бұрын
Well whatbshould the switch read if you need to adjust it?
@SpaGuy3 жыл бұрын
You should never adjust it.. Did you watch the video?
@georgemckinley26866 жыл бұрын
We have a Jacuzzi J335 and there is an error code: Ono. Any idea what that means? The pump barely goes on and then shuts right back off. It was delivered in 2009. We believe it was delivered brand new.THANKS
@SpaGuy6 жыл бұрын
George, That code is not familiar.. On a Jacuzzi Premium the pump does not have to operate for the tub to work and heat as there is a small circulation pump for the heating.. Usually on a J Premium you get a 3 dash code - - - or a low flow.. LF1 or LF 2 or an OH code.. Never seen a Ono.. Spa Guy
@MrLeeRossi4 жыл бұрын
I have a hot springs spa and when you push the jet switch for the pumps it goes right to high on the jets.Do you know what it could be?.
@SpaGuy4 жыл бұрын
Many Hotspring tubs only have 1 speed jet pumps..
@katrinadillard72823 жыл бұрын
I am getting the flo error. Only one side of my hot tub is working. Any suggestions of what it may be?
@SpaGuy3 жыл бұрын
Pump not working..
@katrinadillard72823 жыл бұрын
@@SpaGuy is this an easy fix that I could do? I've been trying to find someone to come out and look at it for me but no one in my are works on hot tubs unless you purchased it from them. Also thanks for responding.
@Chris-ob8ok4 жыл бұрын
Teflon tape isn't a sealant, its actually a lubricant. The only thing doing the sealing on a NPT pipe are the threads.
@SpaGuy4 жыл бұрын
OK if I screw it in without the tape it leaks so like it or not it is a sealant..
@Chris-ob8ok4 жыл бұрын
@@SpaGuy that doesn't make it a sealant. If NPT threads leak that means you have not tightened them properly, something which teflon tape is made to do. It is NOT a sealant.
@TheCrimsonBlade24 жыл бұрын
@@Chris-ob8ok If it seals a leaking thread... what is it?
@Chris-ob8ok4 жыл бұрын
@@TheCrimsonBlade2 it doesn't seal, it's a lubricant. It prevents the threads from binding before making a seal. If it were a sealant it would work on non tapered threads (which it doesn't).
@ericbuzza62656 жыл бұрын
Great Video but I am stumped. We have a 2002 Vita Spa L 200 Series. Ran the diagnostics got the code HC. Everything I read said to replace the Heater. Went to the dealer and they had one. Replaced the heater and it is still not working and still showing HC. I pulled off the circuit board and there is no sign of any burning. I hate to just replace parts although I am sure the dealer likes selling obsolete/discontinued heaters for 248.00. Tub does stay at 85 degrees but that has been slightly lower then the daily temps here. Any advice is most certainly appreciated.
@SpaGuy6 жыл бұрын
Hello Eric, Usually a Hi Limit code is HL or HH not HC.. If it was a Hi Limit code the heater could not be the cause.. What would cause a HL code is the heater staying on with too little water movement or a stuck relay.. Things like that.. You were lucky to even be able to buy a heater as they are obsolete.. I did look up the code and it says HC means heater error and I think those boards has current sensing loops and for whatever reason the system is not sensing the heater drawing current.. That could be bad relays on the board or any number of other things.. Spa Guy
@ericbuzza62656 жыл бұрын
Thanks for the quick response. The dealer has 2 left. The store actually mentioned the relays and did suggest a service call... Should have listened. I hate to send it to the curb because everything is still in good shape including a new cover last fall but I guess they do say all good things must come to an end.
@tinycircle147 жыл бұрын
Thanks so much, but I have an odd problem on my Cal Spa. The high and low pressure pumps work fine without codes, but as soon as the pump turns off, I get a FL code. I jumpered the switch and it kicks back up without issue. Also, if I wait, it seems to clear on its own. So it seems like either there isnt enough pressure in the tube when the pump is off OR the switch is faulty. That seem right? What would cause low pressure code when the pumps are off? (PS. spa runs fine in all jets and filter is clear.)
@SpaGuy7 жыл бұрын
Hello, Based on your description I think the switch is stuck closed.. when your tub gets to the set temp and the pump goes off the system looks for the switch to open if it doesn't it sets a FL code.. Thanks for watching, Spa Guy
@crazieak7 жыл бұрын
I have an ancient Coleman 220 Spa (Circa 1992) and it sounds like I need a new flow switch based upon your video. Do you know if this is going to work for such an old spa? Thanks!
@VitiatedsHOWTO2 жыл бұрын
What codes were you getting I have a coleman spa 400 series maax Arizona edition & I’m getting LO code The hottub worked good before I moved it
@davidstone31197 жыл бұрын
Is the air pressure switch supposed to have two 1/4 inch flexible tubes connected to it since there are two outlets on the switch itself? On a jandy 400,000 BTU.. ?
@SpaGuy7 жыл бұрын
David that is pool style heater and I have never worked on one so I can't advise you on the pressure switch system on that heater.. Spa Guy
@kmreardon067 жыл бұрын
I used your advise and checked the way I reconnected the one M7 (2000LE system) cable and it worked. The tub fired up and was heating the water - we got to about 98 degrees and then it threw a FL code, (The pressure switch is brand new) I have a Balboa system. Any Ideas?
@kmreardon067 жыл бұрын
So I watched this video and tried your lil trick.... I disconnect one wire from the pressure switch and the FL error disappeared.... so Do I need to purchase a new pressure switch connection wire, and if so do you sell them? I have the 1 amp Tec(something or other) pressure switch.
@Reudze Жыл бұрын
My water heat only when I activate the jet manually. But I have no error code. any idea?
@SpaGuy Жыл бұрын
Sounds like you have no low speed on the heating pump.. You have to diagnose why..
@blodgettcreamery12906 жыл бұрын
I have a solana that has a ==== error Pressure switch senses flow through heater even though the jet pump is off? Is this just a replace pressure switch?
@SpaGuy6 жыл бұрын
Jeff, It is possible.. If you measure across the switch and it has continuity with the pump off the switch is bad or out of adjustment.. Spa Guy
@leengagnon37977 жыл бұрын
What to do if the heater won't stop heating? Code OH on Dynasty spa. It reeds 110 degrees. What do I need to check. Thx!
@SpaGuy7 жыл бұрын
Normally the heater itself cannot heat past the set temp, if it goes past the set temp it is something else like a newly installed pump with the speeds backwards or if it has Balboa controls which Dynasty normally doesn't the filter cycles could be set too high.. The other thing would be is the water temp actually 110? If you had a stuck heater relay it would overheat the water in the tube to 110 but not the entire tub of water.. Had you done any repairs just before this started? Spa Guy
@deputys454 жыл бұрын
Great job your awesome 😎
@gseppi7 жыл бұрын
My S-class has the no heat, CR12 Led on. Fuses are fine, flow switch checks out, no power to heater. When I remove and reinstall one wire to pressure switch, right most relay closes but still no 240 to heater. Any suggestions? Getting 17 volts between relay connector and ground and each heater connection to ground. Thanks!
@SpaGuy7 жыл бұрын
Hello, I would suspect a cold solder joint on the bottom tandem relay above the right leg of the heater element on the board... There are three relays related to the heater the left side is a single relay and the right is a tandem set where both have to close for heat.. the top right one closes for the Hi limit and the bottom right closes when it calls for heat.. It is usually the bottom one.. So you can power down remove the screws from the board and pull the board out and look behind it and in the case of an S-Class you can do this without unhooking any wires including he incoming power wires.. This particular board is bad about the bottom relay getting a cold older joint and catching on fire and burning a hole in the board... Therefore if you see soot in the box and it is dark around the right heater tab area it is too late.. Spa Guy
@gseppi7 жыл бұрын
OK I will check. Right now the center relay doesn't close when it calls for heat which is connected to the right relay via jumper wire. Only the right relay closes. Thanks
@SpaGuy7 жыл бұрын
Ok, so you described all of the heater relays closing and even having voltage at them and now you are saying they do not... If you are saying the the small LED on the lower right side of the board is lit and there are 3 dots flashing on the topside that is a High Limit code,,, That is why it is not heating.. You either have a bad board, Hi-Limit or something actually causing a high limit which usually would not happen fast after power up.. Usually if the system is not engaging the right lower heater relay there is a code...
@chrislimbrick81966 жыл бұрын
Spa Guy I have the same problem my board is fine only heats up if I turn the jets on
@chantelleking32157 жыл бұрын
I have a beachcomber energy saver digital 2000 . I'm getting an error code 1- I can't find any code that has 1- any ideas. Thanks in advance
@kirkgregory8182 Жыл бұрын
can the m7 be replaced
@SpaGuy Жыл бұрын
Yes but that has nothing to do with a pressure switch..
@kerricarlin85047 жыл бұрын
So confused!! I have an older hot tub that was never used, a Laser Plus Whirlpool Spa, and it is not heating properly. I have it set on 95 and stays at a steady temperature of 91. When I bump it up to 104 to get in it, it will not heat up until it goes through its cycle then it will heat up. I have turned it off at the main switch and when I turn it back on I hear the pump try to come on but then stop but it will come on if I turn the jets on but will not heat up until it goes through its cycle. There is no error code that comes on, the filters are clean and nothing is stuck in there and it has the right amount of water in it. Made a phone call to someone and they thought it might be my pressure switch. Do you have any idea what it might be before I make this purchase??
@SpaGuy7 жыл бұрын
Based on your description I don't even have a guess.. I need to know what brand of electrics you have.. Also you need to leave the tub at 104 if that is where you use it.. It costs more to keep bringing it up to temp than leaving it at temp.. Thanks, Spa Guy
@laurablair95007 жыл бұрын
Spa Guy h
@MrMike12345767 жыл бұрын
MY BREACKER IS TRIPING WHEN THE WATER GETS HOT WHAT DO U THINK THANKS
@Avery9894 жыл бұрын
MIKE CRABTREE WHY ARE YOU YELLING
@hperez62664 жыл бұрын
Can I get more info on your super duper friend. I need more detail and what's included. Thank you
@SpaGuy4 жыл бұрын
Click on the join button details are there.. I have a bunch of new stuff coming up that will only appear there..
@anthonyscala65593 жыл бұрын
I want to switch seven days ago I still haven’t received it my hot tubs full of algae
My pressure switch # is SPS 0267750 i would like to know wich one is compatible with my watkins 2008 thanks
@mrandtx7 жыл бұрын
Any hints on getting the pressure switch loose? I have a d-tec (your sku HTP47-439-1295) switch and it doesn't want to let go (when turning counter-clockwise)... I'm afraid I'm going to break it off and not have enough to grab onto to remove the rest!
@SpaGuy7 жыл бұрын
You turn in left and lift up some.. On a D-tec the bottom edge of the switch is hex shape for a wrench.. If it does break off usually you can put a flat screw driver in the center and turn it out but if it won't turn out with the switch I suspect the threads are stripped.. In that case you can grad the switch with pliers and twist it out.. Lastly if the switch does break of you can take a plumbing torch and heat the plastic and it will burn out.. Spa Guy
@mrandtx7 жыл бұрын
Thanks for the reply! Yep, I was using an open-ended wrench. Could feel the plastic twist (without it nipple/threads moving). I'll use more pressure and just deal with whatever happens. I was also thinking of trying to use freeze spray on it to get it to shrink slightly.
@yvettesaballa97127 жыл бұрын
any hints to what error code "18" means on an old blue ridge spa?
@SpaGuy7 жыл бұрын
Yvette that code I have not seen a Pressure Switch code is usually a P51 on a Blue Ridge..You 18 may be an upside down 51.. In this case a 5 means the circ pump has been turned on but the pressure switch didn't close.. It could be a Pressure Switch, Circ Pump or filter stopped up.. Spa Guy
@yvettesaballa97127 жыл бұрын
thank you so very much for your quick reply - i pulled out the filters, removed a lil debris and pine needles, put em back in - powered down 3 times - it still says 18 - ive never seen this code before - the econ button or temp buttons wont work but jets work..... strange - thanks again
@landkind50302 жыл бұрын
My pump ist kicking on .. flo message... what's up
@SpaGuy2 жыл бұрын
Diagnose why the pump is not running..
@andrewnormore70938 жыл бұрын
So my pump is surging. Onnnnnnn Off. Ooooooonnnn. Off. Error Code FLO and the pump stops. Would this be caused from bad pressure sensor? I adjusted it ALL the way to the bottom, still FLO. I shorted the leads, FLC came up. Looks like I found it eh?
@SpaGuy8 жыл бұрын
Hello Andrew, No a pressure switch will not cause your pump to surge.. Pump surging comes from many different things.. here are a few things.. Filter stopped up, Low water level, Internal motor issue, Something caught in the impeller, some kind of restriction on the suction side of the pump, if it is a 115V plug n play hot tub running it on a drop cord could cause it... The pressure switch again has nothing to do with the pump running or not... Thanks, Spa Guy
@andrewnormore70938 жыл бұрын
Thanks for the fast reply. I'll take the pump apart today and see what's in there. I'm using a 15 amp cord running from my GFCI cord. You think I need a bigger cable running to the tub?
@SpaGuy8 жыл бұрын
Yes if you are running this on a drop cord that is probably the cause.. Has it ever run correctly on this cord?
@andrewnormore70938 жыл бұрын
This is the first time it's NOT running on 220. I bought it for $200 bucks. I just finished checking the impeller, 100% clean. I just recorded a video, if you can identify what's going on, I'll gladly buy a replacement from your store :) Unless it's the wiring :/
@SpaGuy8 жыл бұрын
Is the pump a 115v pump? The clues are the tub ran before you moved it.. It ran on 230V.. If you converted it back to 115v it has to have a 115v pump in it.. The length of the drop cord make a huge difference... If you have the tub on a 15a 100' cord it will not run on high speed or it will ramp up and surge.. post the video and send me a link here.. Spa Guy