Kirk, what would you recommend to clean slump block? It has never been painted but it is old (50 years) and needs to be cleaned to look nice again.
@StuccoPlastering3 жыл бұрын
Good morning Mark, I'd wait until a rainy day allows the rain to saturate's the bricks and grout overnight, then use your garden hose with a good nozzle to spray off any dust, dirt, or residues.😉 If you can't wait until it rains, then a strong gas-powered pressure washer. The overnight soaking is like a pot with dried or burnt spaghetti on the bottom. One can scrub for an hour to remove it or just soak the pot overnight. The next day, the bottom of the pot is a whole lot easier to clean. Our unique plastering Tip: all subscribers or anyone who stumbles on our channel with a question, type it into our Stucco/Plastering channel, and like magic, a video will appear to explain how it's done. This feature is miles ahead of any plastering forum. 🥳 www.stuccoPlastering.com
@guatehikes10113 жыл бұрын
@@StuccoPlastering Thank you for the info, Kirk. Much appreciated.
@enlightened_herenow9 жыл бұрын
This was one of the best videos I've watched on the Tube, Kirk. Everything you said was true. I washed my CMU wall with a 2000psi, 1.2 gpm electric washer, but as you said 3000psi is probably the minimum to make any noticeable change on the efflorescent build-up. I also tried TSP with the toughest brush I could fine and to my surprise, no change on the build-up, yet made the clean part of the blocks unnecessarily white, but I guess that's OK if I primer and paint the wall. Tomorrow I was going to prime it with a acrylic block fill primer using a 3/4" synthetic nap roller. Then 2 coats of elastomeric exterior waterproof paint, until I saw your other video plastering it and it looked just terrific.I'm now having second thoughts...and might just hold off 'till next weekend. Or, maybe plaster looks good because you're an expert in it, but for a new homeowner that I am I might just go with the paint option, but still wondering if I paint now and a few years down the road, decide to plaster it, can I still apply plaster on paint or should I remove the paint again? That'd be a hassle. Any advice? Thank you for sharing the knowledge.
@1stFlyingeagle6 жыл бұрын
With turbo tips. Treat them like a saw blade. I ran it across my leather boot by mistake and now have a boot with a circle etching. It damages the surface of my work boot. And always wear eye protection. You don't see it coming until it hits you and if it hits your eyeball you could louse that eye. Kirk great video as always.
@StuccoPlastering6 жыл бұрын
Howdy Robert, no doubt, thanks for the tips Live long and plaster, Teaching plastering tips with proper techniques
@StuccoPlastering10 жыл бұрын
DIY Pressure or power Washing Tips And Techniques
@StuccoPlastering10 жыл бұрын
Hello patricia summers, thanks for sharing. Kirk and family
@MrFishone77710 жыл бұрын
Hey Kirk, I've been sandblasting off and on for 20 years. Blasting a cinder block wall with Walnut Shells works really well. You have to watch out you do not blast to much and damage the mortar. You still need to pressure wash after blasting.
@StuccoPlastering10 жыл бұрын
Evening MrFishone777, What city and state are you in? Back in the day I used to refer a bunch of guys to sandblast homes and walls we were to apply color coats on, it seams for the last 15 to years it's now outlawed here where I live. I tell most folks to pressure wash well these days as many people call me expressing frustration at new color coats or skim coat coming off. Thought I would try and set the record straight. Best wishes, kirk and family
@MrFishone77710 жыл бұрын
The restrictions are from county to county. Silica is the problem. There is air quality issues too. I'm not sure if blasting with walnut shells falls under a hazard material restriction. I see the state workers blasting you just have to reclaim all the debris produced. I've been making sandblasted Natural Stone signs in Plumas County, CA for many years. I would imagine that sandblasting with silica sand in the open around any highly populated areas would be illegal. By the way Silica is just tiny Quarts crystals that you find on every sandy beach or river.
@StuccoPlastering10 жыл бұрын
Hi MrFishbone, rules on top of rules. I try and avoid getting yelled at or in trouble with any of the agencies. Cheers! kirk and family
@MrFishone77710 жыл бұрын
I sent a picture for you from your website. Big Fan of yours Kirk. I'm feeling pretty good about trying out some skip-trowel techniques.
@TheRenpeg10 жыл бұрын
MrFishone777 silica sand is tiny particles like asbestos. once it gets into your lungs your in a world of hurt. If you are wet blasting not to much to worry about but dry blasting, mining, and even bad clean up. put alot of those tiny particulates into the air. Im waiting for the lawsuits to start from the mines that mine silica and it and pile it for the oil fracking to start. people all over the area in I believe Oklahoma are developing health issues. Also the epa came out years ago with new regulations on lead and dealing with it. Oh it its a Bitch almost as bad as asbestos with all the suits,respirators and plastic. i understand why but As a business owner all the stuff I had to do to protect everything. But if The homeowner did it they didnt have to worry about dropping the lead paint on the ground or throwing it into the landfill. Ok im done..
@StuccoPlastering9 жыл бұрын
Morning Enlightened herenow, thank you, yes , I have some advice, if you paint a retaining wall, more than likely you will have to paint ofter as retaining walls tend to hold back dirt and when rained on for weeks sometimes leach rain water. This occurrence is paints worst enemy. If you do decide to do this Primer it well as that is what makes the paint adhere and is stronger than the paint so two coats of paint are not necessary, instead go heavy with the primer. If you plaster this wall with a skim coat first then a apply color coat maintenance free cementitious finish, you will never have to worry about this wall agin for 100 years, sure the color may fade in time, but the finish will never come off. Place an add on craigslist seeking a plasterers or hire a licensed fella to do this simply application. In the long run you will be happy you did. Best wishes, Kirk Giordano
@paulrhodes48210 жыл бұрын
Great video! What brand of pressure washer do you buy I see it has a Honda engine but just curious on the brand of washer thank you.
@StuccoPlastering10 жыл бұрын
Hi Paul Rhodes, man, I'm not certain of the brands, as long as they have the honda engine, I like them, I usually buy the top of the line stuff as you get what you pay for. best wishes, Kirk & Jason Giordano's DIY plastering network
@paulrhodes48210 жыл бұрын
No problem I need a new one and looking for 3000psi I will check around I do want the Honda engine for sure thanks again.
@1stFlyingeagle6 жыл бұрын
Home Depot sells P/W. Mine is Dewalt 3800psi at 3.5 gpm 200 dollars more got me to 3800psi And duty cycle is 100%
@83RBurke6 жыл бұрын
I wear neoprene waders to power wash. Kurt’s company? White long sleeve collared dress shirts. Gotta look professional in this biz...! All in fun, good video, ty
@StuccoPlastering6 жыл бұрын
Good Morning Burk Dude, no one will belive I'm a doctor unless I were this white shirt. Live long and plaster Kirk and Jason’s plastering tips and techniques
@mokhan989910 жыл бұрын
Hey Kirk, I want to purchase a swimming pool trowel, but in unsure of what size to get, could you recommend me a size, il be using it for sand/cement rendering,
@mokhan989910 жыл бұрын
Don't know whether to get a 16inch x 4 1/2inch or a 18in x 5in
@StuccoPlastering10 жыл бұрын
Hi Mo Khan, good question the 16X4 is more for concrete as it does not flex as well as say the 16X5 which is for plastering , You can control the mud with your wrist better as the blade flexes a bit more with the 5 inch wide blade An 18X5 takes some practice but for concrete you should get the hang of it after a few jobs, plus it requires less strokes to get the lines out. I sometime use a 20X5 but don't recomend it to anyone as is big, bulky and most folks can't seem to get the feel for it. Best wishes, kirk and family
@mokhan989910 жыл бұрын
StuccoPlastering thanks Kirk, I cant find a 16X5 anywhere in the UK online, but will the following be ok for stucco/render www.transtools.co.uk/hand-tools/construction-tools/concrete-floats-and-trowels/marshalltown-msp815bd-blue-steel-swimming-pool-trowel-float-18in-x-5in?show_vat=0
@Junuuuld7 жыл бұрын
Hello sir Kirk ,I just pressure wash my painted walls and I will put weld Crete. I used 3500 psi. My question is it necessary the paint to be remove when I pressure wash?i pressure wash it the paint not coming out? Thank you sir.
@StuccoPlastering7 жыл бұрын
Good evening Spider man dude, when we pressure wash we do so with the idea that we are going to clean the dust, dirt, grime of the painted surface. I am in happy when all the paint remains on the home. I have hod the opposite where most comes for many reasons, such as a homeowner did not use a primer or the paint has been on with no maintenance for over 15 years. What a drag this is. Stucco is only as good as what is applied over, sounds to me like you did a fantastic job. Live long and plaster teaching repairing your number 1 investment, your home
@Robert-sf3uz6 жыл бұрын
Kirk I am unable to find any videos on removing stucco from cinder block walls. I have researched and seen a few people talk about 4200+ psi pressure washers to remove the stucco. No videos online showing the removal process. Do you run into these requests time to time? Great videos btw!! Happy holidays!
@StuccoPlastering6 жыл бұрын
Evening Robert Dude, yes, I have had my share of pressure washing peeling paint and or stucco. I'd say 3,500 PSI is more than enough pressure. From there you scrape off what is left the following day as the water would have lifted a little bit more, this you scrape off with a putty knife or trowel. The bit that stays put, you can leave it alone knowing you did the best you could, as some houses have really loose stucco in some areas and stucco that is attached so well dynamite could not remove it. FYI, this comes from many men working on one house, some are experts with quality in mind while some are hung over or simply not sure why they are there. I used to have 15 employee's at one time many years back and know this to be indeed a fact. Cheers, peace, harmony & happy holidays Sound Plastering tips from your favorite stucco geeks
@Robert-sf3uz6 жыл бұрын
@@StuccoPlastering Kirk Dude, you are a real life hero! I'll give it a shot. My stucco was put on the backyard cinder block walls back in the 90's and it's looking pretty beat up currently. The goal was to remove entirely, but from what you're saying I should not expect to get back to a wall that looks like it was never stuccoed? Again, I appreciate your guidance/assistance!
@Tony4friends310 жыл бұрын
Hello Kirk, I have a 1955 house that has been exterior painted over at least 10 times...The paint is NOT peeling..I want to re-stucco the house...Which is the best way to get the paint off? Water pressure using gas 3,000 psi rented at Home Depot? Sand Blasting? Then a bonding agent..What are the steps for this if you have time to share.. Thanks, David
@StuccoPlastering10 жыл бұрын
Hi Tony A, in my area, a person can no longer sandblast for at least the last 15 to 20 years. I would pressure wash well, then apply the bonding agent directly to the home. Best wishes, Kirk & Jason Giordano’s DIY plastering and stucco channel
@Tony4friends310 жыл бұрын
Kirk & Jason Giordanos DIY plastering and stucco instructional videos and forum
@Tony4friends310 жыл бұрын
Kirk & Jason Giordanos DIY plastering and stucco instructional videos and forum Following up on your answer about re-stuccoing my 1955 house..I have pressure wash my entire house by using a rented home depot 3200 psi machine...Next is the bonding agent...However, question: I bought Weld Crete and you said to dilute it to 50/50 on the painted surfaces, is that right, because due to spidering affect in you don't...(yes I have watched over 15 of your videos,lolol)..With that said, I have replaced all windows and have a scratch coat, brown coat or whatever you guys call it that is ready for the color coat...The question is: at those spots which is just cement do I cover it with weld crete 100% several times to make that texture the same as the painted pressure washed house? Thanks for everything, the videos are great and really help DIY people like me...Thanks man
@StuccoPlastering10 жыл бұрын
Good morning Tony, a slight misunderstanding may have occurred, I say to dilute Larson's bonding agent (weld crete) when applying a color coat over a painted surface then apply directly to the home. However when applying a scratch, brown and color finish over a painted surface, You want to apply the weld crete at full strength, enough to really hold almost a solid inch of stucco. If you apply it full strength then apply a (only) a color finish, this 1/8 of an inch of finish will hairline like a dropped egg. Doubtful any harm is done, call my home phone and leave me your best call back number, so I can get a better idea of what you're doing. 510 521-9546 Cheers and have a Happy New Years, Kirk Giordano’s DIY plastering tips
@Tony4friends310 жыл бұрын
Kirk & Jason Giordanos DIY plastering and stucco instructional videos and forum Mr. Giordano, thanks for the great offer to call you and discuss this, what a offer...However, I would rather email you with a picture of the house so you can get the true idea as I don't know how to explain it as best as I should. Is it possible to get your email or I'll send you mine: tony4friends3@gmail.com...thank you so much and thanks for the individual care and concern you have already shown to make my house improvements... Tony
@geedubb200510 жыл бұрын
not only does it take the hide off, it's pretty damn painful when it does it. Kinda like getting a road rash at 400 mph/
@StuccoPlastering10 жыл бұрын
Hey Gee Dubb, hate to say it but I touched the spray myself once too, Ouch, won't being doing that again, but I did do a boot afterwards one day when I was really bored and had been pressure washing for hours just for the hell of it, lets just say I won't be doing that goofy shit anymore either. Live and learn. cheers. kirk and family
@Tipperary7578 жыл бұрын
Thanks for the video! How long do you think for a thorough dry on basement walls and floor so paint will adhere? Guesstimate or things to look for to determine dryness (in addition to touch)? I know cinder block is more porous than cement and wicks water deeper like a sponge. thanks.
@StuccoPlastering8 жыл бұрын
Morning tipperary links, good question, Depends or ventilation and the weather, open all window if it's hot the dryer condition will dry out in a week or so. If there no warm air flow use fans to dry out. Best wishes, Kirk giordano Plastering
@TheRenpeg10 жыл бұрын
love turbo tip aka grenades.
@StuccoPlastering10 жыл бұрын
Hey dusty, Grenades sounds like a good name for these tips as they do look like that. Cheers! Kirk and family
@Joebunkyss18 жыл бұрын
a bit of 10:1 hcl acid in a squirt bottle first works wonders.....not on stone....but bricks and blox are fine.....i figure theres a reson you dont.
@StuccoPlastering8 жыл бұрын
Hi Scott, good tip, cheers, kirk giordano
@shantelfullerton98658 жыл бұрын
Go to inplix page if you'd like to know how to build it. Great solutions for everyone I think
@StuccoPlastering8 жыл бұрын
Morning Mate, thank you cheers, Kirk and Jason’s rendering videos