Does this panel have the capacity of self monitor, or be monitored by the customer via App or cell phone?
@speedlva4 жыл бұрын
Too much extra information. You could talk about the problems with the smaller panel at the end of your video. It makes your video(s) hard to follow.
@peterkulka4703 жыл бұрын
Can I program Vista20iP using Compass 2.0 and direct TCP/IP connection to network connector mounted on side of Vista20iP panel? I was reading a lot about iton the web, but not to much information about how to do. One of Honeywell bulletins it say to install "Compass Connect Control Server" and "Compass Connect Data Server". I downloaded and installed both servers from my (mywebtech) account on to my laptop and configured IP addresses accordingly. I also matched same IP address in Compass 2 settings for communication via TCP/IP. When I checked box "Enable TCP/IP" and select ECP under "Connection Mode", I get only one option "AlarmNet-ip" but "Private-LAN' is gray out. Under this configuration I'm not able to get connection with panel. I'm getting message: "Connection failed to control server due to either Wrong Server IP Address or Server is not running" My both Control Server and Data Server are running, IP address on both servers, my laptop and Compass 2 are the same. When I select under Connection Mode "Direct Wire", I'm getting message "This Panel currently doesn't have Direct Wire TCP Connection Mode capability" My Vista-20iP firmware is 4-26 Please advise.
@joshuagriffin28073 жыл бұрын
the communicator must be programmed to an A360 account. the private lan is for 7847IE that have the 7810PC receiver set up. There is an option to use a hayse modem to direct connect over the phone connections
@plastica77323 жыл бұрын
there is no web interface that could be accessing by web browser direct to the local iP of the Vista-21iP?
@joshuagriffin28073 жыл бұрын
There is a total connect 2.0 service that is a paid service. would require an account number with an alarm company.
@glassmancarter4 жыл бұрын
Can I monitor it with my cell phone through the internet? I have my 20p programmed to dial my cell phone.
@dylanalarm_grid10384 жыл бұрын
You'll need to get an ip communicator such as the 7847i as well as needing to get the system registered to the Alarmnet servers. If this is something your interested in check out our monitoring plans: www.alarmgrid.com/monitoring
@najjamitat95174 жыл бұрын
Which is the best Alpha-numeric keypad to use to configure the Vista 21IP for initial setup? Can this be done with a touch screen such as Tuxedo?
@najjamitat95174 жыл бұрын
@Bryce Alarm Thanks for the information.
@zipstuff3 жыл бұрын
I get all the way to the end but it says "done" after hitting review "N" #, it doesn't update the root file
@freddaniels82593 жыл бұрын
This has to be connected with a dealer to have access to the servers. If you are going through a dealer you may want to have them check it out for you.
@somalsharma31752 жыл бұрын
do i need the 6160rf to program this unit or will a 6160 working fine ?
@dylanalarm_grid10382 жыл бұрын
Either keypad would be a good option to program the VISTA-21IP. If you're wanting to add wireless sensors to the system, and do not already have an existing RF receiver, then that is when you'd go with the 6160RF keypad.
@somalsharma31752 жыл бұрын
@@dylanalarm_grid1038 thank you so much for that
@yeungwilliam20913 жыл бұрын
Can I use the IP alarm monitoring service in other country ? Or how the 21iP connect to local CMS ?
@joshuagriffin28073 жыл бұрын
we have self-accounts around the world we cant monitor them with our monitoring station. you can use the TC2 account. to get the TC2 app sometimes the region would need to set to the United States to get the tc2 app
@yeungwilliam20913 жыл бұрын
@@joshuagriffin2807 what kind of communication protocol when use IP alarm ? I need to check the local CMS to see they can accept.
@ColdComrade3 жыл бұрын
I press 1 for program and my keypad goes blank
@AlarmGrid3 жыл бұрын
This indicates there's a problem with the panel not being able to pass data traffic with the communicator. If you're attempting to use the internal Vista-21iP IP/Cell communicator, then make sure the jumper is set to ON for the internal communicator. If you need to move the Jumper, NEVER DO IT WITH THE SYSTEM POWERED ON. If you're trying to use an external communicator, then be sure the jumper is set to OFF. If the jumper is set to ON, and you're trying to use the Internal Communicator, then there is an issue, and it could be a bad panel/communicator combo. The jumper I'm referring to can be seen in this FAQ: www.alarmgrid.com/faq/does-my-vista-21ip-support-4g-cellular-communication-link-to-vis
@anmg20243 жыл бұрын
so i guess there is no way i can install something on my server in cloud and monitor it from there ...or have that to send an alarm to my cell phone ..otherwise a nice video
@dylanalarm_grid10383 жыл бұрын
You can have the alarm send your phone alerts if the panel is setup with Total Connect 2. If you are interested in learning more about this application, feel free to send an email to support@alarmgrid.com.