I like your method for the initial alignment of the gear pairs. However, when setting the mechanical gear constraint, another method is to select the pitch circle diameters of both gears. Solidworks will calculate the gear ratio based on the sizes of the 2 pitch circles. If you later change the ratio of the gears, then the gear constraint will automatically update. This method of setting the gear constraint is also very useful when using timing belt pulleys.
@YangCaoUBC9 жыл бұрын
Thanks for the input.
@tageldesta99238 жыл бұрын
I like your method for the initial alignment of the gear pairs.
@DerPrediger6 жыл бұрын
Thanks mate, it was a frustrating way until i found this video. I owe you one. ♥
@user-wi6hg3zo7z2 жыл бұрын
professor yang, really appreciate you.
@denisl27609 жыл бұрын
I like to use physical dynamics to check if the gears turn properly, seems a little more satisfying than using mechanical mates.
@TKO1779 жыл бұрын
This was incredibly helpful for my project. Thank you very much!
@richardcavanagh6 жыл бұрын
Another great video, thank you.
@kaanceylan10317 жыл бұрын
that was smooth
@rachakondavarun519 Жыл бұрын
super video it is very helpful
9 жыл бұрын
Totally perfect. Thank you !
@richardlsmith905711 ай бұрын
Hi there, do you know why solidworks spur gears only allow certain diametial pitch values, is it due too gear wear, or gearing issues?
@balbi9566 Жыл бұрын
thanks a lot
@LOL09102710 жыл бұрын
You speak good English mate, proud of you as a Chinese!!
@user-ou1yc1pk2h2 жыл бұрын
nice lesson, thank you
@bikesh459 жыл бұрын
I have a problem, when I increase the number of teeth my dedendum circle diameter gets bigger than the base circle diameter but this should be the other way round...Can you help me please? Thanks in advance
@siddharthgupta58389 жыл бұрын
where can i find your earlier tutorials? thanks
@naimaimanroslan68429 жыл бұрын
Hello Mr.Yang Cao..can you show me how to do BEVEL GEAR assembly? Thanks
@sumitmandlik53678 жыл бұрын
Why dont you use gears from toolbox components?
@tomkhodorkovsky14777 жыл бұрын
Great video, thanks! Question: how come a gear can't have fewer than 13 teeth? I've googled my ass off about this and came up with nothing.
@YangCaoUBC7 жыл бұрын
If the gear ratio is 1:1, with pressure angle of 20 degree, the smallest number of teeth on a spur pinion is 13.
@rakeshpillai217310 жыл бұрын
Hi, Wonderful tutorial. Could you clarify why the front planes have to be made coincident when you have already made the front surface of the gear and pinion coincident?
@stanleyka20644 жыл бұрын
Hi, I have a problem with this. Both of my gears are having the same diametral pitch but when I am arranging the gears, it seems the teeth would interfere with each other. Can anyone enlighten me on this?
@KleinLim8 жыл бұрын
Why can't I select the centerline?
@rishabsud75354 жыл бұрын
As we have applied 5 rpm to the driver, please tell where can we find the rpm of driven gear through software?
@God0fTime4 жыл бұрын
idk through the software but the output rpm is the input rpm multiplied by the Train Value
@brotherschannel98108 жыл бұрын
thank u
@johnhoyle63904 жыл бұрын
mate PD circles to tangent
@georgekazma20227 жыл бұрын
At 10:38 you hit green checkmark but you only had one line selected. That's why the two lines were not actually conicident when you tried moving the gear. I really hate it when someone claim to be an expert in SolidWorks and post videos for the public. Yet they make silly mistakes that waste the person's watching time !