How to Fix Timber to Brickwork - Fencing and Gates

[@projectgaming3364]

QUICK TIP: Drill your holes before you cut the angle... that way they'll definitely be 90 degrees to the brick when fixed! Quality video as usual. 👍

[@pepperhill]

Fantastic tip. Thank you

[@MohitKaura]

Could you explain this a bit more? I am trying to do a fence gate, so this might save me time.

[@jamesfukndee]

But if uou drill before you cut the wood, it would go in at an angle, the idea is to drill after cut so it's straight to the brick

[@projectgaming3364]

​@jamesfukndee no mate it will mean it goes into the brickwork at 90* and have a proper fixing. Best to drill then cut.

[@mikeflowerdew7877]

​@@projectgaming3364 you'd be right if the cut face were facing outwards, but he's got it the other way around, cut face against the wall. So, the holes are perpendicular to the cut face, not the original sides. So, cut then drill is correct in this case.

[@muso31]

Great channel - quick tip on this one... place galvanised square washers behind the post that's fixed to the wall to keep the timber off the brick and avoid damp

[@jimporter]

Remembering that the countersink should not be based on the size of the bolt head but the size of the socket you’re going to use to fix it.

[@guysolis5843]

True dat..

[@craigprosser9554]

@@guysolis5843 it is no need to ask how I know😂

[@bowenflob8036]

Remembering that it's a counterbore not countersink as that would imply chamfering the through hole, not drilling a blind bore as he did

[@YAWN....]

Ok Dad...

[@bowenflob8036]

@@YAWN.... Pleasure

[@NAFO_Badger_Brigade]

Always clear! Greatest handyman teacher on the web! Love those fixings - seem so much better than the hammer in type which I've never been happy with!

[@ProperDIY]

Wow, thanks!

[@robjenkins9450]

Everything about this procedure is spot on and very well explained. I've just used a similar method to fix a 100mm square gate post. For those with particularly brittle bricks or London's with the large frog, I'd suggest using 10mm allthread and chemical fixing adhesive such as Kem II. Recessing the timber holes is done in the same way, allowing for a nut and washer. Remember to check your thread lengths so they don't fall short to apply the nut and washer. For those keen on a fine finish can always plug the holes once complete.

[@GaryAppledale]

This was a revelation. I was waiting for you to drill a hole large enough for a big old plastic rawlplug and you just screwed the bolt straight into the brick! I just never knew you could do that.

[@ProperDIY]

I know! looks like rawlplugs are old fashioned now!

[@james-jq8sk]

Depends on the type of brick, sometimes they just don't work...

[@stevegeek]

Exactly what I was expecting to see. I'll have to look out for some of these concrete screws when I replace my gate post.

[@AlanBrown-r7z]

This concrete screws idea will solve my current problem of an existing post has come loose from what looked like thin screws into rawlplugs into house brickwork. The whole fence is unstable at the house end and raking it apart is not in my capability or strength. I can drill through the wood post in situ though and put those heavy duty concrete screws in. Grateful for this video!

[@LeighWinspear]

Great video and good advice. 9:07, no need for pilot holes if you use a cutter design, of outdoor quality screw such as reisser. But as usual you will pay more for the convenience and time saving.......;)

[@debbiefinch7445]

WOW! Once you mentioned bevelling the post i nearly tuned off - far too complicated for me I thought - but you simplified working out the angle so well that even an idiot like myself can work it (not that i need to because my wall and fence are parallel to each other!) The only other element I found not very DIY basic was the laser thingie - not got a one of those and don't want to waste money on a piece of equipment just to attach 3 posts. Had tuned in mainly to see what you used and was pleasantly surprised to see no raw plug required. Years of doing my own DIY from laying patios, house renovations, electrics, plumbing - i have never plucked up the courage to drill into brick!! Flippin' simple following your video!!Thanks alot!! x

[@statuescher]

Another great guide with loads of relevant details. A good tip I saw on another channel is to silicon seal the top and sides of the gate posts to the wall, the bottom is left open to let any moisture run out. Also installing the post off the ground level by an inch or two helps stop it rotting. Thanks

[@Shadman1603]

Great job! Used these bolts to fix my timber to the wall yesterday when I put a gate up. Never heard of them before but they fixed really solid.

[@jatflash]

Well mannered presentation, good instruction and no fluff. Well done.

[@ProperDIY]

Thank you

[@goblin7837]

Well said mate!

[@andyr4735]

Literally thousands of videos on KZbin and this video is recommended everyday.

[@Clicknick007]

Great video. Have done much of this over the years. I have drilled slightly smaller holes in the brickwork for concrete bolts to ensure. 10mm bolts, 10mm hole in post, 8mm holes in block/brickwork. I also drill and loosely fix bolts one at a time starting at the top, so you don't have problems if there is any movement.

[@olenaerhardt7725]

Really appreciate this film. I need to replace rotten pieces of Door Jambs on our garage door, watched several films and was about to do an easy project, but then realized that all the films I saw before were about attaching that Door Jamb to the wood, and we have brick house, with the Door Jamb attached to the brick. The project turns to be from easy to not so easy, but I can proceed after this film. Thank you!

[@ProperDIY]

No problem - I'me glad you liked it and found it useful

[@olenaerhardt7725]

@@ProperDIY I have another a question here: can I actually use the original holes and concrete screws? I will cut like 24 in from the bottom of the Door Jamb and replace it with a new piece of wood. Or I need to make an attachment in another place? In other words if you unscrew that concrete screw, can you screw it back, or it is like an ancor in some sense, and it is better not to reuse it? Thank you again.

[@ProperDIY]

@@olenaerhardt7725 Yes you can reuse them and the holes. Just ensure that when you tighten them fully they hold well - this sort of depends on how hard the brick/block is. If it's normal brick it will be fine.

[@olenaerhardt7725]

@@ProperDIY I see. Thank you very much.

[@jahedul.H]

My first time watching your videos and in the first 5 minutes I instantly subscribed. Great video mate

[@ProperDIY]

Thank you - very much appreciated

[@rickydub6950]

Same here 😁

[@paulr9572]

My top tip for using concrete screws and bolts is to have some bamboo skewers handy, so if the bolt doesn't get a good hold of the brick for whatever reason, trim one to the right length and pop it in the hole first. Works every time!

[@Lord-Panda2112]

You are really natural in front of the camera. I'm surprised you aren't on a professional show. You have good charisma are well informed and entertaining. Impressive.

[@ProperDIY]

Thank you so much 🤗I haven't been offered any show but I do have my own channel with no one telling me what to do so good enough for me!

[@Lord-Panda2112]

@@ProperDIY Fair enough!

[@MattTaylor-uj3ye]

A spade bit produces a counter bore. A countersink is typically 45 degree taper for countersink screws. Yes a good informative video.

[@stevebeal73]

I had a similar issue a few years ago, but wanted to fit a gate. I didn't bevel the fence posts though - I simply fitted the hinges to the flush fence posts in the normal way and let the hinges absorb the angle. Worked well and looked good!

[@donohoe71]

Why have I not found you earlier! Excellent video, I'm crap at DIY but you take it step by step and explain everything without it becoming boring. Really pleased I've found you. Thanks mate, keep up the good work

[@ProperDIY]

Thank you and Welcome aboard! Only been going since Jan so still very new to everyone!

[@tasercs]

1st of your videos I have watched. Not sure I have seen a more concise, well paced, well edited DIY video as yet. Also excellent camerawork and audio (including sensible use of music instead of a constant bed fighting with the presenter). I'm really looking forward to watching loads more. :)

[@viper7869]

At last somebody who knows what they are talking about! Good tips good advice!

[@ProperDIY]

Very much appreciated!

[@adamstone4905]

In regards to the post fixing 100% the fencing on the other hand is not correct bottom rail to low, using screws instead of 50mm galv nails and no gravel board support in the middle good effort nevertheless (I’m a fencer)

[@stevehall6299]

Top marks for PPE use!

[@thetruthz13]

No idea how I ended up here. I'm not even putting my own fence up. But I had to see the finished article. Looks great! And very informative. Good job. 👍

[@ProperDIY]

Glad you enjoyed it!

[@somewhereelse3813]

This guys a legend. Are you local cos my wife's crap at DIY!

[@ProperDIY]

This is easily the best comment I've had so far!!! Very good!

[@hugowilliams4999]

This video is very helpful, wonder why I didn't search before. I love the step by step explanation, great. I am a DIY er and this adds to improving my abilities. Looking forward to watching more.

[@delfokronic]

If I could go back and do it all again, this is what I'd be learning. So satisfying.

[@Belly-u2w]

I've been a fan of Dynabolts for years but those anchor bolts have just changed my mind.

[@saajanji1674]

Brilliant no long winded story telling, few ground rules and off we go. We'll done

[@ProperDIY]

Thank you!

[@zgasnola]

Really impressive job. I was just looking for tips on fixing gate posts to the wall, but really liked the fence and all the handy tips. Thank you.

[@ProperDIY]

Thanks. Just assume the fence post is a gate post!

[@mrmrjims3865]

Justin Timberlake would be proud

[@RandomnessTube.]

I watched this in full and enjoyed it I must be getting old.

[@ProperDIY]

I know the feeling!

[@NeverWokeNotASoiBoy]

By old i think you mean wise?!

[@raminybhatti5740]

😁👌

[@veganpotterthevegan]

Yup, how-to's for things we're never going to do. I don't have a single brick on my house but I'm here 🙃

[@taters-no4gj]

Going to be doing a gate and a little bit of fencing. I was worried about the screws I'd use, or if I needed to use rawplugs, etc, and whether to drill into the mortar or brick. All questions answered and all concerns set aside. Excellent vid. Many thanks 👍🏻

[@dantovey2785]

Lovely job. Those concrete screw fixings are brilliant

[@ProperDIY]

Thank you

[@Brian-om2hh]

I'd agree. I used them to fit a canopy over my back door... Worked a treat.

[@francefradet2116]

This is like a City and Guilds workshop lesson. Wow. Thanks.

[@DjGiluk]

I’ve been watching your videos the last few days to get some ideas - they are great so thank you. Keep up the good work and I love the humour 👏🏻👏🏻

[@ProperDIY]

Glad you like them! Will do

[@HIK_48]

Excellent tips. I never think of using line but to mark where the Arris rails are over featherboard, it's the only way!

[@karamathussain406]

Great advice always nice to watch these kind of videos they help you do the job only once rather than wastage. Thank you and please keep them coming.

[@ProperDIY]

Thanks, will do!

[@BUREAUTOM]

Great video. Top marks on the way you explained how to trim the post. A difficult thing to explain. You did it very well - the advice was very clear and easy to follow.

[@jixuscrixus1967]

Subscribed, good presentation, straight talking, clear instruction/advise and an easy manner.

[@ProperDIY]

Thank you.

[@ThetraindrivingGK]

Cheers for the great guide, i'd never used concrete bolts before, will definitely use again.

[@charlesarnold4963]

I found that extremely interesting and useful. Would you consider showing how to fix a post to and irregular brick wall please? By irregular I mean a brick wall that is not straight up and down.

[@GeeTheBuilder]

Just found your channel. Looks good. Personally, and we all have our different ways, I have learnt over the years to always resin when affixing to brick/concrete. Yes, concrete screws can be very strong, but resin is fit and forget. Nice to see a fellow 🇬🇧 doing stuff like this on KZbin 👍👏

[@ProperDIY]

Thanks! I agree resin is absolutely the best fixing into a wall like this. In my day job I have used construct resin like Hilti Hit' which will fix anything. The negative side is it's permanent and not cheap. The average DIY'er will not be inclined to use resin.

[@polderfamily442]

@@ProperDIY Hello Stuart. Also very impressed with the concrete anchors into the brick. Are you able to tell us the manufacturer and name of the product? Would like to see if they’re available in the US. Love the videos!

[@cbaker1249]

Absolutely brilliant, real professional, well explained, and suitably informative and inspiring enough for me to do mine! well done!

[@ProperDIY]

Thank you very much

[@chrisfirth461]

Great video thanks, I learned quite a bit from that. Could I suggest that you cut a hole at the bottom of your fences to allow hedgehogs access? Lack of hedgehog highways is one of the reasons they are in decline.

[@AJ-qn6gd]

Vital tip 👍🏻, we have hedgehog holes in front back and side fences and we regularly have hedgehogs in the garden sometimes they even hibernate in our hedgehog houses 😀🇬🇧

[@chrisfirth461]

@@AJ-qn6gd Excellent, thank you for that, they need all the help they can get.

[@ProperDIY]

Good point - a job for me tomorrow.

[@AJ-qn6gd]

@@ProperDIY,Top man 👍🏻🇬🇧

[@SBNewMe]

Brilliant. Some great tips there. Is anyone else screaming 'gate! - make an access gate!!'....no, just me?

[@jeta1f35]

Cracking video, all bases covered, plain speaking, very well edited, spot on !

[@ProperDIY]

Much appreciated

[@iriswigle]

Great suggestions...loved the string to line up the screws. Loved the intro wherein you shaved off some of the 4 by 4. I would not have lowered the bottom 2 by 4 to ground level or below due to rain and in Canada snow. Animals will just dig under. Wind will eventually move the fence possibly as I left mine open in between a little....sort of...a 80 year old neighbour from Ukraine wandered over and took over. He could not speak English so the screws did not line up...and there were some things that he did that I would not...but my Lancaster mother taught me to respect age...hmmm? I loved the drawings. I guess when I make the gate, I will not trim off the 4x4 but will move the opposite side on the 90 degree angle and hope it works as I try to do an l shape to a metal fence...right? Well, as long as it holds to the grandchild is old enough to walk into the front...a good 2 years. But, thanks for sharing...quite professional. Oh,....thanks for the idea of countersinking the bolt. I am a super and the men that, long ago, did a fence and gate...did NOT sink the screws which seem to have caused a gap in the apt where I am living so the gate is tight due to the screws

[@slodown3670]

Excellent!

[@chrisdowning7543]

Hi Stewart, thanks for your kind reply. All done now, you were totally right about the intense bitting in the wall!! It fixes extremely well indeed. Much much better that old fashioned rawl plugs! Thank you!

[@ProperDIY]

Excellent! I'm so glad it went well.

[@G58]

The mechanical advantage of a screw thread driven by a 12” ratchet over a 6ft length of 4” pine is huge, especially with high tensile bolts. It would be easy to obtain a 2” deflection over a 6ft length. I’ve tried to use the stuff for forming jigs, and it’s useless. Only oak, ash or 6” pine was good enough. Nice work. I like your attention to detail on the join to the main fence.

[@ProperDIY]

Quite right!

[@floatingpeaks4584]

I use a pritt stick to fix timber to brick work, saved me a fortune over the years.

[@judithwoods1576]

I'm doing a similar job and I found your video very helpful. Thanks

[@swisstony6069]

Really enjoyed the vid. Professionally done with no faffing around, well done. I’ll be checking your other vids.

[@ProperDIY]

Thank you Swiss Tony! Lots more to come.

[@tonyefc8423]

Very like myself. Some 'belt and braces' stuff, but that's good. As a joiner who's had to retire through illness, i find your videos informative and interesting.

[@ProperDIY]

Well thank you very much.

[@liberifatali666]

Ahh this is excellent! Exactly what I been looking for. Complete DIY noob here, had a pop at hanging a gate off the concreate post after (eventually) ripping out the ol' rotten one... After about 6 hours and a lot of swearing as my spindly little bolts kept snapping I came to learn the error of my ways. this video should do me justice, I feel much more comfortable tackling this., I'll let you know how it went:P Again, thanks a lot

[@MarkJT1000]

This is why a professional job sometimes costs more than you'd expect. It takes a lot more time and effort to do the job properly. I used rawl plugs and large 10mm screws when I fixed my post to the wall. It seems secure enough.

[@ProperDIY]

Correct

[@damirsavka836]

You can even use counter sunk anchor screws, for a flush finish

[@BarneyTrent]

Always tended to use the shield anchor bolts but they look a tad outdated. Will be giving these concrete screws a try now they look ace. Good job 👌🏼

[@ProperDIY]

Me too and they now seem a bit old fashioned!

[@jeffthomas9517]

Good advice Jim, 👍I've done similar but used Dyna bolts to attach the timber to the brickwork, but your method is neater. Cheers Jeff.

[@jtbkilmartin9110]

Awesome advice. Thanks a million. Ive done some fencing before but there are a load of good tips from you. Nice one.

[@ProperDIY]

Thank you

[@PBz420]

Thanks for the great insight and step by step guidance on the fencing!

[@ProperDIY]

Thank you

[@KpxUrz5745]

I work like you do, proper planning at each step. The problem comes if I try to hire someone. Cannot find contractors capable of this kind of exacting workmanship.

[@ProperDIY]

Exactly. Even with their so called 'professional training' no one seems to care as much about the detail as yourself!

[@Chequr_Prostate]

Lol. Contractor and exacting workmanship! They area rare species indeed. If you can find one to do even a half decent job you’ve won the lottery. Your only hope is to do it yourself!

[@apocreg11]

I don’t even have this in the job list but still enjoy knowing how to!

[@wax0val]

great vid. did not need music but that aside I learnt a lot. Really helpful, packed with tips. Thanks

[@ProperDIY]

Glad you enjoyed it!

[@susanhillier5635]

Having watched you build the garden planter, you took this to another level. First class job, it makes a difference having all the tools but you certainly know what you are doing..........keep it up 👍

[@ProperDIY]

Thank you

[@glynprice3815]

As an apprentice wood machinist. One my jobs was cut the arris rail ends to a bit of point. And make matching holes in the post.

[@ProperDIY]

Nice one!

[@garulusglandarius6126]

Love your work Stuart, I’ve watched every video and your attention to detail how AND why is so useful. My only complaint, more videos please I’m getting withdrawal symptoms 😂👍

[@Ilimar1]

Great video, but I wondered the entire time If a fence that would open wouldn’t have been a better item to put on that side of the house. Now you have to walk all around the building to get to the other side.

[@selffarming7008]

Great video, well explained, like the solution to the angle on garage wall. Another top job fella 👍

[@jon.bennett]

Great video. Easy to understand and kept it simple.

[@ProperDIY]

Thanks

[@Bthaman69]

Omg thank you. I literally have the same project with the same geometry. You're #1

[@markbarlow4918]

8:24 onwards for a couple of seconds.... shut your eyes and just listen!!! 😂🤣😂🤣 Brilliant video, really informative and well put together!

[@ProperDIY]

Glad you enjoyed it!

[@Chequr_Prostate]

Great video, my only concern would be the bridging of the damp course.

[@2icelollys1goat]

Thank you. Really well produced video tuition. And I liked your humour🙂

[@ProperDIY]

Glad you enjoyed it!

[@kezcracknell]

Brilliant video, Bravo. Makes it look easy but also gives me the confidence to do it myself. Thank you.

[@ProperDIY]

Thank you

[@krstolaganin2495]

@@ProperDIY mk

[@krstolaganin2495]

@@ProperDIY k

[@vladimirimp]

I really enjoyed this video, now subscribing. I like your presentation style - very informative.

[@ProperDIY]

Thank you.

[@markmiller6402]

Great video, very professional mate.I too was shocked at how much those concrete screws gripped.

[@ProperDIY]

Thanks

[@kevinwaters60]

Don't know how I found my self here but it was very educational. Now to do a vid on that snapped fence post in the back ground 😉

[@ProperDIY]

I will do

[@craigbuckley4832]

Very impressed by how it's turned out,. Very good video 👍 well done

[@gonzo3915]

I use these floor bolts for all my wood to Stone fixings, great things.

[@robplazzman6049]

Impressed by those bolts gripping hold !

[@ProperDIY]

Me too. If the brick is strong the fix is solid

[@raydebbiemcdonald3208]

Nice job. Love the detail of scribing then end board. A proper job! 😊

[@ProperDIY]

Glad you liked it!

[@TheWebtuts]

Spot on direction, like those bolts going to give them a go for double side gates posts. 👌

[@jamesst16]

Nice video, used these fixings to hang a gate post on my brick wall. Top tip = spray the hole through the wood and the brick with some wd40 before putting the fixing in. Saves that nasty squealing and makes them easier to do up.

[@chris_hertford]

You can put nylon spacer between post and brick stops damp traveling.

[@darren78anderson]

This guy is the father figure I wish I'd had 👌

[@ProperDIY]

That makes me feel old however I'll take that as a compliment.

[@garybowles8340]

Really enjoyed watching this one! Very good way of showing how to make a template for the angle to cut. 👏👏👏

[@ProperDIY]

Thank you

[@peterleid5060]

Thanks for this. Good to see the job done properly. I fear that left to my own devices, I'd have missed a couple of steps out. I'm hoping my subscription to your channel will keep me on the straight & narrow. You need to re-think the background music... methinks. ⭐️⭐️⭐️⭐️⭐️ 🇬🇧

[@ProperDIY]

Thank you!

[@tee2899]

Get rid of the muzzak altogether we stopped the vid because of it

[@feroxvenom5082]

Brilliant job 👌🏻only criticism is the gimmick music I think you don't need that in you're video's ..... Subbed look forward to seeing what you do next .

[@ProperDIY]

Thank you

[@BURP39R]

Painful that generic yt music. Your content is fine without it.

[@johnauld0]

Excellent video exactly what I’ve been searching for….new subscriber 👍

[@ProperDIY]

Welcome aboard!

[@Gank-SquadUK]

Thank you for providing such excellent material

[@edwardwilson4974]

Really good stuff, and quite inspiring seeing such good work. Thank you!

[@ProperDIY]

Glad you enjoyed it!

[@Peter-Casey]

I’m just a diy dad who’s now taking a 15 year old pressure treated deck apart It’s biggest failure part was the ( post direct to wall in this vid ) My question as a diyer : would it have been any benefit to put a plastic packer between the post & brickwork to allow airflow through Any advice appreciated & thanks 🙏 again for your time making another excellent vid

[@joneades2493]

Great to see you using your safety gear!

[@ProperDIY]

Always have to else I'll get told off by the Safety Manager!

[@dogbreath6974]

Another great video Stuart. Not sure if you have one but, you could do with a drill press, it would make it easier for drilling 90 degree holes.

[@harwoods11]

Great video... Gotta love KZbin 👌 I especially liked the end panel detailing... Very professional indeed. Plan your jobs, get your tools charged up and get the correct fittings (but check KZbin first)

[@ProperDIY]

Thank you

[@MrJono1999]

Great video, superb explanations. I did not even know these bolts existed, this will be very helpful in the future. It's just a shame I miss half of what you say as I keep having to turn the volume down between talkie bits. The video's are great the music is just annoying.

[@ProperDIY]

Glad you liked it

[@staninjapan07]

Nicely done, Mr. DIY, or may I call you Proper? Looking for videos on fixing metal parts to concrete, I was offered this, which, while not being what I was looking for, was still a "fencetastic" video. Thanks from Japan. Liked. Subscribed.

[@ProperDIY]

Glad to help all those based in Japan. I bet they don't have a 'Proper DIY' equivalent in Japan!

[@staninjapan07]

@@ProperDIY Well now, there is no "yes or no" response to that. While DIY (as I, as an English guy would see it) is much less commonly done here than it is in the UK, basically as people have far too little time as they have to work a lot, the people who do do it take it very seriously. The Japanese are fastidious and careful learners and they believe in doing EVERYTHING as the experts tell them to do it. So there are home centres in every town (not quite as "DIY" as Smith's Do It All used to be when I lived in the UK), but they have a fair selection of tools etc. So to answer whether they have an equivalent of Proper DIY... I would say there are many. I happen to maintain my own motorbikes (I had some time at a Toyota dealer in the early 1990s) and Japanese language bike maintenance videos are very common indeed on KZbin. Have a good day, I will be enjoying some more of your videos when I have another free 20 minutes.

[@stevenbarratt7409]

Fantastic. your work is immaculate. thanks for sharing.

[@electrickal1]

We call those screws "Thunder bolts" here in Ireland. They really are a leap in the right direction.

[@nateb7394]

Looks great! Say you want to move that fence in the future (for whatever reason), could you fill in the holes you made in the brick with something? Some sort of outdoor-rated brick filler?

[@fiddef6414]

Watched this very clear explanation and subscribed right away for future stuff.

[@ProperDIY]

Thank you